Range / Cooktop / Oven Burner & Related Parts

This burner head is the gas-fired surface component that supports and directs the burner flame for cooking. It restores proper flame pattern for safer, more even heating on compatible gas ranges. What it does:

• Directs and shapes the gas flame so heat is applied evenly to cookware
• Helps maintain stable ignition and consistent burner operation
• Can reduce uneven cooking, weak flames, or burner flame distortion
• Works with the burner cap and base to form the complete surface burner assembly

• Turn off the gas supply and unplug the appliance before servicing
• Remove burner grate and cap, then lift the old burner head straight up to remove
• Seat the new burner head fully on the burner base and replace the cap and grate
• After reinstalling, check ignition and flame; if you detect gas odor or leaking, stop.

This black burner skirt fits around a 5K simmer burner ring to restore proper appearance and support the cooktop surface. Replaces cracked or damaged skirts to keep the burner area sealed and looking finished. What it does:

• Provides the decorative and protective trim around a 5K (5000 BTU) simmer burner
• Helps keep spills and debris from entering the burner cavity
• Restores even contact and alignment for the burner assembly
• Commonly replaced when the skirt is cracked, warped, or missing

• One black burner skirt (5K)

• Turn off and disconnect power and gas supply and allow all surfaces to cool before servicing
• Remove burner caps and grates per your model's service instructions to access the skirt
• Handle carefully to avoid bending or cracking; hand tools usually sufficient

This conversion kit contains the parts needed to change a compatible gas appliance from one fuel configuration to another, helping restore safe, efficient operation after a fuel-type change. What it does:

• Provides the specific orifices and fittings required for converting a compatible gas range/oven or appliance between fuel types
• Helps correct burner performance issues caused by mismatched fuel setup
• Enables appliance to meet proper fuel pressure and flow when converted as directed
• Intended for use only when appliance requires a manufacturer-specified fuel conversion

• Turn off gas supply and power before starting; verify no leaks after installation
• Use only the parts and adjustment procedures specified for your appliance model

This burner cap is the replacement top piece for a gas cooktop surface burner, restoring even heat distribution and protecting the burner head from spills and debris. It helps the burner produce a steady, efficient flame. What it does:

• Centers and shields the burner head while directing flames for even cooking
• Helps maintain proper flame shape; can reduce uneven or lifting flames
• Prevents food and liquid from contacting the burner base and ignition area
• Useful when the original cap is cracked, chipped, warped, or badly corroded

• One replacement burner cap

• Allow the cooktop to cool completely and shut off gas/electric power before replacing
• Lift off the old cap and set the new cap onto the burner base so it seats flat and centered
• No special tools required for most installations; test the burner at low flame and adjust seating if needed
• If flames are irregular after installing, double-check cap alignment and cleanliness of the burner head and ports

This burner tip directs gas flow to the burner for reliable ignition and steady flame patterns. It replaces a damaged or clogged tip to restore even heating and consistent burner performance. What it does:

• Guides the gas to the burner ports so the burner can ignite and burn evenly
• Helps maintain a consistent flame for proper cooking temperatures
• Can resolve symptoms like weak, uneven, or noisy flames when the tip is damaged or clogged
• Works with the burner assembly as the gas outlet component

• Inspect and clean the surrounding burner area before installation; ensure the appliance is fully disconnected from gas and power
• Hand-thread the tip to avoid cross-threading; tighten per manufacturer torque recommendations if available
• Use only on compatible burners as specified by the appliance manufacturer

This burner cap fits over a gas range surface burner to help direct the flame for even cooking and protect the burner head from spills and debris. Replacing a damaged cap restores proper flame shape and improves cooktop performance. What it does:

• Centers and shapes the gas flame for consistent heating across cookware.
• Protects the burner head from food, grease, and moisture that can impair ignition.
• Can resolve uneven or distorted flame appearance and reduce burner noise caused by damaged caps.
• Works with the corresponding burner base and cap seating system for safe burner operation.

• Turn off the range and ensure all components are cool before handling.
• Remove the old cap, clean the burner head of debris, then set the replacement cap into proper position—no tools usually required.
• Follow the appliance manufacturer's service instructions and safety warnings when servicing gas components.

This burner cap is the replacement top piece for a surface gas burner, restoring proper flame shape and heat distribution for reliable cooking. It helps protect the burner head and keeps the flame centered for consistent performance. What it does

• Centers and shapes the burner flame for even heating across cookware
• Protects the burner head from spills and debris that can block ports
• Helps prevent yellow or irregular flames caused by a damaged or misaligned cap
• Common symptom: uneven or weak flame, burner flame that drifts or won't stay lit

• Turn off the range and ensure all surfaces are cool before servicing
• Lift off the old cap from the burner head; no tools are typically required
• Set the new cap flat and centered on the burner head so it sits flush
• If problems persist after replacement, inspect the burner head and ports for blockage