Range / Cooktop / Oven Gasket & Seal

This oven door gasket creates a heat-tight seal between the oven door and frame to help retain heat and improve cooking consistency. Replacing a worn gasket reduces heat loss and limits smoke or steam escaping during use. What it does:

• Seals the oven door to help maintain internal temperatures and consistent cooking results.
• Reduces heat and steam leakage that can cause longer cook times or uneven baking.
• Typical signs you need it: visible gaps, flattened or torn seal, or heat/steam escaping from the door.
• Matches OEM fitting style for a direct replace of the damaged or degraded seal.

• Disconnect power to the oven and allow it to cool completely before starting.
• Access the gasket per the manufacturer's guidance—some doors may need to be opened or removed for easier access.
• Remove the old gasket from the channel, then press the new gasket evenly into the channel so it seats fully around the door perimeter.
• Reuse original retainers or hardware; if adhesive or clips are required, follow the oven maker's instructions.

This burner seal is a replacement gasket that fits around a cooktop burner to help keep the burner area sealed and easier to clean. It helps maintain a proper seal between the burner base and the cooktop surface. What it does:

• Seals the gap between the burner and cooktop to limit food, grease and liquid from entering the burner cavity
• Helps keep the burner seated and reduces wobble or misalignment
• Supports cleaner cooktop surfaces and simplifies wipe-downs
• Can help maintain consistent ignition area by keeping debris away from the burner base

• Turn off power to the appliance and ensure the cooktop is completely cool before starting.
• Remove burner grate and lift off the burner cap and burner head as needed to access the seal.
• Clean the seating area of any grease or debris, then press the new seal evenly into place before reassembling.

This replacement door gasket seals the refrigerator door to help maintain proper temperature and prevent moisture buildup. A worn or torn seal can cause cooling issues and higher energy use. What it does:

• Creates an air-tight seal around the refrigerator door to help maintain internal temperature
• Reduces frost and moisture buildup by preventing warm, humid air from entering
• Helps improve efficiency and consistent cooling when the original gasket is damaged
• Commonly used when the existing seal is torn, stretched, compressed, or leaving gaps

• Inspect cabinet and gasket channel for debris before installing; clean surface for a proper seal
• Align gasket evenly and press into the channel; some models may require gentle stretching or heating per OEM guidance
• Do not use sharp tools that could nick the gasket; replace if the flange or trim is damaged

Replacement gasket that restores a tight seal to the appliance door and helps prevent water or air leaks. Replaces worn, cracked, or compressed seals so the door closes properly and reduces moisture or heat loss. What it does:

• Seals the door opening to stop leaks of water, steam, or heated air.
• Helps maintain proper temperature and efficiency by preventing air exchange.
• Reduces condensation, odors, and cycling caused by a poor seal.
• Common signs you need this part: visible gaps or damage, leaks around the door, excess moisture, or poor heating/cooling performance.

• Disconnect power and water (if applicable) and allow the appliance to cool before starting.
• Clean and dry the mating surface to ensure a proper fit; remove old adhesive or debris.
• Align the gasket into the door channel or groove and press evenly; avoid stretching the material.
• If the door or mounting hardware is bent or damaged, repair those parts before installing the gasket.

This seal for the front frame creates a tight barrier between the oven door and frame to help retain heat and reduce smoke or odor escape. It restores a proper door seal to improve cooking performance and safety. What it does:

• Replaces worn, torn, or deformed front-frame gasket that allows heat or smoke to leak from the oven cavity
• Helps maintain consistent oven temperatures for more even cooking and baking
• Reduces heat transfer to surrounding cabinetry and surface areas
• Stops drafts, burning odors, or visible gaps around the door edge

• One seal for the front frame

• Disconnect power and let the appliance fully cool before attempting service
• Inspect orientation and seating before final installation; some models require door removal for access
• Use proper tools and gloves to avoid cuts; ensure seal is fully seated and continuous around the frame

Replacement refrigerator door gasket that restores a tight seal to help maintain proper cooling and reduce frost and moisture buildup. Fits the door channel to stop warm-air leaks and improve overall temperature stability. What it does:

• Seals the refrigerator door perimeter to keep cold air in and warm air out.
• Helps reduce frost and ice buildup inside the compartment.
• Can reduce condensation and uneven cooling caused by a worn or damaged seal.
• Common symptoms of a failing gasket: warm spots, excess frost, visible gaps around the door, or higher-than-normal energy use.

• Unplug the appliance and remove food from the door area before beginning work.
• Clean and dry the gasket channel and door surface; align the gasket and press it fully into the channel for an even seal.
• If the gasket is stiff, gently warming it can make installation easier—avoid excessive heat.
• Confirm this part number matches your appliance model before installing.

This solid lower door gasket seals the bottom edge of the dishwasher door to help keep water inside the tub and reduce leaks during cycles. It restores the door's seal for reliable performance and quieter operation. What it does:

• Forms a watertight seal along the dishwasher's lower door edge to prevent leaks
• Helps maintain proper wash performance by keeping water inside the tub
• Reduces door rattling and noise caused by a worn or missing seal
• Compatible with units that use a one-piece solid lower door gasket design

• One solid lower door gasket

• Inspect door and mounting channel for debris or damage; clean before installing the new gasket
• Press the gasket into the door channel evenly, ensuring a flush seal along the entire edge
• Avoid using sharp tools that could nick or tear the gasket during installation
• Disconnect power to the appliance before performing any service to reduce shock risk

This burner seal is a replacement gasket that fits around a surface burner to help keep food and liquids out of the cooktop cavity and make cleanup easier. Simple wear replacement for torn or collapsed seals. What it does:

• Forms a protective gasket between the surface burner and cooktop to limit spills and debris entering the cavity
• Helps keep the burner cap seated correctly and reduces grime buildup around the burner area
• Makes routine cleaning faster by preventing trapped food and liquid
• Common signs you need this part: visible gap or torn seal around the burner, frequent debris buildup, or a burner cap that sits uneven

• Turn off the cooktop and gas supply and allow all parts to fully cool before starting.
• Remove the burner cap and lift out the old seal; align and press the new seal into place around the burner opening.
• Reinstall the burner cap, restore power/gas, and test burner operation for correct seating and appearance.

This door gasket seals the refrigerator door to help keep cold air in and warm, humid air out—reducing frost build-up and helping the appliance run more efficiently. Fits where a full perimeter door seal is required. What it does:

• Creates an airtight seal around the refrigerator door to maintain consistent internal temperatures.
• Helps prevent warm air infiltration, moisture, and frost accumulation inside the compartment.
• Reduces energy waste caused by a failing or damaged door seal.
• Common symptoms of a bad seal: condensation at the door, frost on shelves, fluctuating temperatures, or higher energy use.

• Disconnect power to the appliance before attempting any service.
• Remove the old gasket carefully; replacement typically seats into the door channel around the full perimeter.
• Inspect and, if needed, adjust door alignment and hinge condition to ensure a proper seal.

The Seal is an OEM part for Frigidaire ranges. It creates an airtight seal between the oven and cooktop surfaces to contain heat and contain spills. Located around the edges of the oven cavity and cooktop surfaces, the pliable and flexible seal conforms precisely to fit the contours and gaps. 

Symptoms of a bad Range Seal include:

• Excess heat escaping from oven cavity around edges  
• Discolored or melted seal from continuous heat exposure
• Gaps allowing spills to leak underneath surfaces
• Increased energy costs from heat loss

This replacement is also compatible with some Electrolux, Gibson, Kelvinator, and Kenmore models.

A general-purpose appliance adhesive used to bond and seal interior and exterior components. Restores secure attachment of trim, insulation, and small panels so parts stay in place and function properly. What it does

• Bonds loose trim, gaskets, and small plastic or metal panels to prevent shifting and rattles
• Seals minor seams and gaps to improve fit and finish
• Helps reattach insulation or padding that has come unglued
• Reduces noise from vibrating parts by securing components

• Clean and dry surfaces thoroughly before applying for the best bond
• Use in a well-ventilated area and avoid skin or eye contact; follow product safety directions
• Apply sparingly and allow full cure time per manufacturer instructions before reassembling

A flexible pan seal that helps keep the refrigerator's drain pan and base area sealed to reduce leaks and contain condensation. Replaces a worn or damaged gasket to help prevent water pooling and odors. What it does:

• Seals the drain/condensate pan to the cabinet base to limit water leaks and vapor escape
• Directs condensate toward the drain so water drains properly instead of pooling
• Helps reduce musty odors from standing water in the pan area
• Commonly replaced when you see water under the appliance, pooling inside the cabinet, or visible gasket damage

• Disconnect power to the appliance before beginning any repair
• Remove the appropriate access panels or kickplate to reach the pan area per your model's service instructions
• Clean the pan and mating surfaces thoroughly before installing the new seal for a proper fit
• Press the seal into place; do not force or use solvents/adhesives unless specified by the OEM

This foam tape seals and cushions the oven door assembly to reduce vibration and help keep the door glass and inner components stable. It restores proper spacing and helps reduce rattling or light air leaks around the door. What it does:

• Provides a soft, compressible seal between the door and frame to reduce noise and movement
• Cushions and protects glass and trim from contact and vibration
• Helps limit minor air leakage that can allow heat or odors to escape
• Commonly used when door trim or glass is loose, rattling, or shows visible gaps

• One adhesive-backed foam tape strip

• Clean and dry mating surfaces before applying to ensure good adhesive contact
• Measure and trim to fit; press firmly along the full length for proper adhesion
• Replace only with the same style of tape—do not use electrical or non-heat-rated foam in high-temperature areas
• Disconnect power/cool the appliance before working on the door assembly to avoid burns or injury

This small pan seal replaces a worn or damaged sump/pan gasket to help stop leaks and keep water inside the appliance's drain area. It restores a proper seal so the appliance can drain without pooling or seepage. What it does:

• Seals the small pan/sump area to prevent water from leaking onto the floor
• Helps maintain proper drainage and reduces pooling under the appliance
• Restores a tight gasket where cracks, compressions, or wear allow seepage
• Commonly used when you see water under the unit, drips after cycles, or visible gasket damage

• Disconnect power and water supply before servicing the appliance
• Remove access panels and clean the mating surfaces before installing the new seal
• Press the seal into place evenly; ensure it sits flush in the pan/sump channel
• Inspect surrounding parts for damage and replace any brittle or warped components

This small burner gasket seals the cooktop burner to help keep spills and debris out of the burner cavity for more reliable ignition and easier cleaning. It replaces a worn or brittle gasket to restore the burner's fit and seal. What it does:

• Creates a tight seal between the cooktop and the small surface burner to help prevent food, liquid, and debris from entering the burner area
• Helps maintain consistent burner alignment for reliable ignition and even heating
• Reduces the need for frequent deep cleaning by blocking spill penetration
• Commonly replaced when the gasket is cracked, flattened, burned, or missing

• One small burner gasket

• Disconnect power to the appliance before servicing; for gas ranges, turn off the gas supply when applicable
• Remove burner components and replace gasket, ensuring it seats evenly around the burner opening
• Do not force or stretch the gasket; inspect surrounding components for damage and clean surfaces before installing

This switch seal is a replacement gasket that helps keep moisture and debris away from the appliance's door/control switch, protecting the switch assembly and helping restore reliable door detection and operation. What it does:

• Seals the area around the door/control switch to block water, lint, and grime.
• Helps prevent intermittent trips or failures caused by moisture or foreign material contacting the switch.
• Promotes consistent switch actuation and can extend the service life of the switch assembly.
• Useful when the existing seal is cracked, torn, flattened, or missing.

• Disconnect power before servicing to avoid electrical shock.
• Access typically requires removing the door trim or control panel—follow your model's service instructions.
• Inspect the switch and surrounding area for damage or corrosion and clean before installing the new seal.