Range / Cooktop / Oven Leg Or Foot

Adjustable front leveling leg threads into the base corner of your range to raise or lower the unit. Replace if broken, cracked, or missing to level your range.

This factory screw secures panels, brackets, and other components in your cooking appliance. Replace a missing, stripped, or corroded fastener to restore a tight, rattle-free fit and keep parts properly aligned during use.

• Fastens components to maintain proper alignment and stability
• Helps prevent vibration, rattling, and loose parts during operation
• Replace if threads are stripped, the head is damaged, or the screw is missing
• Commonly used to mount internal or exterior parts in ranges and wall ovens

• Disconnect power and allow the appliance to cool; shut off gas supply if applicable
• Use the correct driver bit to avoid stripping the screw head
• Install in the original location and do not overtighten
• If the receiving threads are damaged, repair or replace the mating part before installation

Leveling leg installs on the bottom corner of your range to provide stability and height adjustment. Replace if broken, stripped, or damaged during moving.

Screw that adjusts and secures the leveling leg to your range base or bracket. Replace if stripped, bent, or missing to restore stable footing and level your appliance.

This replacement roller fits the front or rear position of a slide mechanism, restoring smooth, even movement and reducing noise when a wheel is worn or broken. It helps racks or drawers glide properly and stay aligned. What it does:

• Provides low-friction rolling support for the slide track
• Helps slide-out assemblies move freely without binding or scraping
• Worn or damaged rollers can cause sticking, squeaking, or uneven travel
• Restores proper alignment and smooth operation when replaced

• 1 roller assembly

• Disconnect power and allow the appliance to cool before servicing
• Remove the slide-out assembly; note roller orientation and hardware
• Transfer/reuse existing screws, clips, or retainers as required
• Do not lubricate unless the manufacturer specifies a lubricant

Metal leveling leg screw threads into your range base to adjust height and stabilize the unit. Replace missing, bent, or stripped screws for level footing.

Adjustable leveling legs that stabilize your range on uneven floors. Replace broken, worn, or missing legs to eliminate wobbling and ensure your range sits level.

Replace missing, worn, or cracked rubber grate feet on your gas range or cooktop. These heat-resistant pads cushion burner grates and protect surfaces.

Replacement foot assembly for gas cooktop or range grates. Installs on the underside to cushion contact and stabilize the grate. Replace when worn, missing, or broken.

Includes one foot pad. Four are required for each grate. Order as needed. For kit of 8 grate feet with adhesive, order 5304475129.

Adjustable leveling foot that stabilizes and levels your appliance on uneven floors to stop rocking and improve overall stability. Simple replacement for a worn or damaged foot to restore a solid, level setup. What it does:

• Threads into the appliance base to support weight and set the appliance height
• Lets you level the appliance to stop rocking or tilting on uneven floors
• Helps reduce vibration and shifting during operation
• Common symptom fix: appliance wobbles, is unlevel, or rocks when pushed

• Disconnect power and pull appliance away from the wall before working underneath
• Support the appliance so it cannot tip; adjust the foot by turning until the unit is level
• Recheck level front-to-back and side-to-side; tighten any retaining hardware if present
• If rusted or stuck, use penetrating lubricant and proper tools; avoid forcing parts in a way that could damage the cabinet

This replacement leveling screw secures and adjusts an appliance's leg so the unit sits level and stable on the floor. Restores proper tilt for even door operation and stable performance. What it does:

• Replaces a worn or damaged leveling screw used to raise or lower an appliance leg
• Helps stop rocking, reduce vibration, and keep doors aligned
• Common fix when an appliance tilts forward/back or is uneven on the floor
• Works with the corresponding leveling leg/assembly to set final height

• Support the appliance before adjusting or removing leveling hardware to prevent tipping
• Use appropriate hand tools; tighten securely but avoid over-torquing
• No electrical disconnection is typically required, but unplug if working near electrical components
• If the leveling leg assembly is damaged, replace the entire leg/assembly per manufacturer instructions

Rubber foot cushions and stabilizes burner grates on your cooktop. Replace worn, missing, or cracked feet to keep grates level and protect the surface.

Threads into range base to support and level the appliance on uneven floors. Replace if foot is worn, cracked, broken, or missing to restore stability.

Leveling leg kit for ranges and wall ovens. Includes adjustable feet to stabilize and level your appliance. Replace cracked, bent, or missing legs.

Leveling foot for gas ranges. Installs at the base to adjust height and stability. Replace if broken, cracked, or missing to level your range properly.