Range / Cooktop / Oven Trim

Color: Bisque. For black order 8184858. For white order 8184859. Kit includes two side pieces and one bottom piece. NOTE: This part has been redesigned by the manufacturer. The lower screws are no longer used and the side trim now locks into the lower trim with the dimples on the lower end of the side trim.

The side trim is a finishing piece that covers the appliance's right edge. Replacing a damaged or missing trim restores the factory look and helps keep adjacent panels aligned for proper fit.

• Finishes and protects the right-side edge of the unit for a clean appearance
• Helps align and secure adjoining panels or console components
• Reduces unsightly gaps that can collect debris
• Common symptoms: cracked, chipped, warped, loose, or missing trim; rattling or poor panel alignment

• Disconnect power to the appliance before service; allow hot surfaces to cool
• Wear cut-resistant gloves—edges and surrounding panels can be sharp
• Note right-hand orientation; transfer any clips/brackets from the old trim if present
• Align tabs and fasteners carefully; tighten hardware just snug to avoid distortion

This door trim kit replaces the perimeter trim on the appliance door to restore a clean, factory finish. It covers and protects the door edges when the original trim is cracked, warped, or missing.

• Frames the door perimeter for a finished, uniform appearance
• Helps cover raw edges to prevent snags and rattling
• Replaces cracked, warped, or missing trim pieces
• Common signs include loose or missing trim, cosmetic damage, and gaps along the door edge

• Disconnect power (and gas, if applicable) and allow the appliance to cool before service
• Support the door; remove it if your service information recommends
• Carefully remove old trim; handle glass and sharp edges with cut-resistant gloves
• Align and secure the new trim; avoid overtightening fasteners and verify smooth door operation

This bottom trim assembly replaces the lower front trim on a 30" range or oven, restoring a finished stainless appearance and protecting the lower cabinet area. It fits where the original lower trim has dented, scratched, or separated. What it does

• Covers and protects the lower front of the appliance cabinet and kick area
• Restores the oven/range's finished stainless look after cosmetic damage
• Prevents dirt and debris from collecting beneath the appliance front
• Helps maintain proper airflow by keeping the lower opening closed

• One bottom trim assembly (30" stainless)

• Designed for front/lower mounting; follow the appliance service manual for exact fastener locations
• Use proper tools and avoid overtightening to prevent stripping or warping the trim
• Disconnect power to the appliance before working near electrical components

The Control Board is an OEM part for GE ovens. As the central control unit, the control board monitors and regulates critical cooking functions such as temperature settings, timers and safety features.

Causes of a bad control board can be normal wear and tear over time, exposure to heat and moisture leading to corrosion of electronic components, or accidental damage.

Symptoms of a bad control board include:

• Unresponsive control panel or dim/missing display
• Inability to select bake or broil temperatures
• Failure to preheat or maintain proper temperatures
• Safety sensors not functioning correctly

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This oven vent directs hot air out of the oven cavity and helps maintain proper internal temperature and airflow. It replaces a damaged or warped vent to restore venting performance and oven appearance. What it does:

• Channels heat and steam out of the oven cavity to support even cooking
• Helps prevent heat buildup behind the oven and adjacent cabinetry
• Replaces cracked, bent or discolored vent trim that can affect airflow or appearance
• Compatible with factory vent locations — installs where the original vent was mounted

• Designed for rear/top vent mounting; verify orientation matches your appliance before installing
• Disconnect power to the appliance before beginning any service to avoid shock or injury
• Handle edges carefully; use appropriate tools to remove mounting screws and clips
• If vent damage is extensive or other components are affected, inspect surrounding parts and wiring

This front trim frame restores the finished edge and appearance of the appliance door or control opening, providing a clean, factory-look replacement that covers gaps and worn trim on compatible units. What it does:

• Replaces damaged, scratched or missing front trim to improve the appliance's appearance.
• Covers gaps where original trim has warped, peeled, or broken.
• Helps maintain a consistent seal line and edge protection around the door or control opening.
• Matches the original black finish to blend with the surrounding cabinet or door surface.

• One black front trim frame.

• High-level replacement; remove power and open door or panel before starting.
• Handle trim carefully to avoid scratching the finish during installation.
• Retain and reuse any original clips or screws when possible; replace only if supplied or specified.

Right hand side. For the left side order 814374.

This bottom trim is a replacement lower front finishing piece that restores the appliance's appearance and helps keep the kickplate area protected from dirt and damage. Fits where the original lower trim is cracked, chipped, or missing. What it does

• Covers the refrigerator/oven lower front to restore a finished look and hide internal components
• Protects the kickplate area from scuffs, dirt, and light impacts
• Replaces cracked, broken, warped, or faded trim that affects appearance
• Matches white finish for seamless visual restoration

• Disconnect power to the appliance before beginning work
• Typically installs with existing screws or clips after removing the toe/kick grille
• Handle the part carefully to avoid scratching the finish during installation