Range / Cooktop / Oven Valve

This water inlet valve controls water flow to the refrigerator's dispenser and ice maker so you get reliable ice and chilled water. Replaces a failed valve to restore proper water supply and prevent interruptions. What it does:

• Opens and closes to route household water to the dispenser and ice maker when activated
• Helps ensure proper filling of the ice maker and water dispensing
• Can cause no water from the dispenser or ice maker if failed or clogged
• May leak or drip when seals or diaphragms wear out

• Disconnect power and shut off the water supply before starting work
• Replace only with the exact part number; inlet/outlet fittings match your unit
• Inspect supply lines and electrical connectors for damage; tighten or replace as needed

This replacement gas valve regulates gas flow to the appliance's burner assembly so the unit can ignite and reach proper heat. Use this exact-fit valve to restore reliable ignition and consistent heating performance. What it does:

• Controls and meters gas flow to the burner assembly for safe ignition and stable flame
• Replaces a failed or leaking valve to stop intermittent or no-heat operation
• Addresses symptoms such as burners not lighting, weak or inconsistent flame, or the appliance failing to heat
• Works as the original-style valve designed for the specified 210 / 15,000 configuration

• Turn off gas supply and electrical power before starting work; follow local codes
• After installation, check all connections and test for gas leaks with a proper leak detector or soapy-water test
• Do not attempt to disassemble or repair the valve; replace if defective

This top burner gas valve controls gas flow to a single cooktop burner, restoring proper flame control and allowing safe ignition and adjustment. It's designed as a direct replacement part for compatible gas ranges. What it does:

• Regulates gas to one top/burner for steady flame control
• Helps resolve symptoms like burner failing to light, weak or inconsistent flame, or inability to adjust flame level
• Works with the burner orifice and valve stem assembly to modulate gas flow
• Intended for use only on compatible range models and configurations

• Turn off gas supply and disconnect power before servicing
• Use proper fittings and torque; inspect connections and test for leaks with a gas leak solution after installation

This water inlet valve controls water flow into the refrigerator for the dispenser and ice maker, restoring proper water delivery and ice production when the valve is functioning. It replaces a failed or leaking valve to stop water loss and restore operation. What it does

• Directs and regulates incoming household water to the ice maker and dispenser.
• Stops water flow when the refrigerator is off or valves are closed to prevent leaks.
• Commonly linked to symptoms such as no water to the dispenser, slow water flow, or no ice production.
• Can cause leaking or pooling under the refrigerator when the valve body or fittings fail.

• One new water inlet valve assembly.

• Disconnect power and shut off the water supply before beginning any repair.
• Expect to access the valve behind the lower access panel or at the rear of the refrigerator.
• Tighten supply line fittings securely and check for leaks after reinstalling and turning the water back on.

This thermal cutoff is a temperature-sensing safety thermostat that helps prevent overheating by interrupting power when excessive heat is detected. Use it to restore proper safety protection in affected appliance heater or control circuits. What it does:

• Monitors temperature and opens the circuit if heat rises above the designed threshold
• Helps prevent overheating-related damage or fire risk in heating systems
• Stops power to heating elements when a fault causes unsafe temperatures
• Commonly used with ovens, dryers, and other heater-equipped appliances as a fail-safe

• One thermal cutoff

• Power must be disconnected before inspection or replacement to avoid shock or injury
• Handle the part carefully and observe wire connection orientation; replace with same type only
• If other components show heat damage, inspect the whole heating circuit and controls

A replacement safety valve kit that restores a safety shutoff component to appliances, helping stop flow when a fault is detected so the unit can operate safely. Fits compatible Frigidaire appliances that use this OEM kit. What it does

• Replaces the appliance's safety valve assembly to restore proper shutoff function
• Prevents continued fuel or water flow when a fault or unsafe condition occurs
• Commonly used when the appliance fails to start, fails to heat, or shows safety-related shutdowns
• Helps resolve intermittent operation or safety trip symptoms tied to a failed valve

• One safety valve kit (single complete replacement kit)

• Disconnect power and gas/water supply before starting any repair
• Follow the appliance's service manual or wiring diagram for correct routing and connections
• Use proper tools and safety gear;
• Test for leaks and proper operation after installation and before returning the appliance to service

This mini burner valve controls gas flow to an individual cooktop/range burner, restoring proper ignition and flame control for affected burners. Designed as a direct-replacement service part for compatible gas ranges. What it does:

• Regulates gas flow to a single burner so the burner can light and hold a steady flame
• Commonly replaces valves that leak, stick, or fail to modulate flame size
• Used when a burner won't ignite, has uneven flame, or cannot be adjusted properly
• Works with the cooktop's ignition and safety systems to deliver controlled fuel to the burner

• One burner valve (mini)

• Turn off the gas supply and unplug the appliance before starting any work
• Use appropriate tools and replace any gaskets or fittings as needed; do not overtighten
• If you smell gas, stop work immediately, ventilate the area.