Range / Cooktop / Oven Valve

Solenoid valve controls the appliance's water inlet using an electrically actuated plunger to open and close flow. Replacing a failing valve helps restore proper filling and can stop leaks, overfilling, or no-fill conditions. What it does

• Electrically opens and closes the inlet to allow water into the appliance during fill cycles.
• Shuts off water flow when the valve is de-energized to prevent overfilling.
• Common symptom fixes: no water fill, continuous filling, visible leaks at the inlet, or related fill/flood error codes.
• Interfaces with the appliance inlet hose and the electrical connector for timed/controlled fill cycles.

• One solenoid valve.

• Disconnect power and shut off the water supply before starting any repair.
• Handle electrical connectors carefully; ensure correct orientation and a secure connection.
• Inspect and replace any worn seals, gaskets, or hoses to prevent leaks after installation.

This surface burner valve regulates gas flow to a cooktop/range burner. Used in the left front or right rear position, it restores smooth knob control so the burner lights and the flame adjusts properly from simmer to high. What it does:

• Meters and shuts off gas to a single top burner
• Position-specific: intended for the left front or right rear location on the manifold
• Helps resolve issues like a hard-to-turn knob, inconsistent flame height, or a burner that won't adjust as expected
• Can correct no-gas flow to that burner when the original valve is blocked or failed

• 1 gas surface burner valve (LF/RR orientation)

• Shut off gas supply and disconnect power before servicing
• Lift the cooktop/top panel to access the manifold; note hose/tube routing and valve orientation
• Transfer any orifice holder/fittings from the old valve as required; avoid overtightening compression connections
• Use an approved gas-thread sealant if specified and leak-test all joints with a soap-and-water solution before use

This bake solenoid controls gas flow to the main oven's bake burner. When energized by the control, it opens the safety valve so the igniter can light the flame and the oven can heat and maintain your set temperature. What it does:

• Opens and closes gas flow to the bake burner during a call for heat
• Works with the igniter/flame-sensing system to light the bake flame
• Helps maintain set temperature by cycling gas flow during bake
• Typical symptoms of a failing solenoid: bake burner won't ignite, igniter glows with no flame, or the burner lights then shuts off

• One bake solenoid for the main oven

• Disconnect power and shut off the gas supply before servicing
• Access the oven valve/solenoid assembly per your unit's service manual
• Transfer electrical connectors one at a time; ensure proper orientation and secure fit
• After reassembly, restore gas and check all connections for leaks with a soap-and-water solution

This gas surface burner valve controls the right-rear burner on your cooktop or range, regulating gas flow as you turn the knob. Replacing a worn valve restores consistent ignition and precise flame control at that position.

• Regulates gas flow to the right-rear surface burner for on/off and flame level control
• Common symptoms include no ignition, uneven or weak flame, or poor flame adjustment at that burner
• Stiff, loose, or wobbly knob action at the RR position can indicate internal valve wear
• If a gas odor is detected, shut off gas and have the unit serviced before use

• Disconnect power and shut off the gas supply before servicing
• Remove the knob and front panel to access the manifold; note valve orientation and connections
• Support the manifold with a second wrench while loosening/tightening fittings to avoid damage
• After installation, perform a soap-solution leak test on all connections and verify proper ignition and flame

This water inlet valve controls the flow of water to the refrigerator's dispenser and icemaker, ensuring reliable water delivery for drinking and ice production. Replace a failing valve to restore normal water flow and prevent leaks. What it does:

• Opens and closes to supply water to the dispenser and icemaker when needed
• Stops water flow to help prevent continuous filling or flooding
• Commonly used when dispenser water is weak, icemaker won't fill, or there is leaking near the valve
• Matches OEM function and fit for compatible Frigidaire refrigerators

• One water inlet valve

• Shut off water and power to the appliance before starting any repair
• Handle water lines and electrical connectors carefully; replace worn gaskets or seals as needed

This top burner valve controls gas flow to a single cooktop burner so you can adjust heat and restore proper burner operation. It replaces a worn or failed valve to help burners light and hold a steady flame. What it does:

• Regulates gas flow from the manifold to one surface burner for precise heat control.
• Replaces valves that are stuck, hard to turn, or fail to deliver consistent flame.
• Helps resolve symptoms like a burner that won't light, weak or uneven flame, or loss of ignition control.
• Works as a direct replacement when the original valve is damaged or leaking.

• One top burner gas valve.

• Turn off gas supply and electrical power to the appliance before starting work.
• Only install on compatible gas ranges; follow OEM instructions and local codes.
• Use proper fittings and sealants rated for gas; check all connections for leaks after installation.

This top burner valve controls gas flow to a single cooktop burner, letting the burner light and the flame adjust for cooking. Replacing a faulty valve restores normal gas flow and flame control. What it does

• Regulates gas flow to the cooktop's surface burner so flame size responds to the knob setting
• Commonly needed when a burner won't light or the flame won't stay lit
• Can correct uneven or weak flame output at one burner
• Works with the burner assembly and control knob to provide user control

• One top burner valve

• Shut off the gas supply and power to the appliance before beginning any work
• Gas valve replacement may require removing the cooktop or burner assembly and using basic hand tools
• After installation, check all connections for leaks with a proper leak-detection method

This burner valve controls gas flow to a single surface burner, restoring proper heat output and reliable ignition when the valve is functioning. It's the direct replacement part that lets a burner reach its correct flame level. What it does:

• Regulates gas flow to one cooktop burner so the flame responds to knob position
• Enables steady ignition and consistent heat for normal cooking
• Common symptoms it addresses: burner won't light, flame is weak or won't stay lit, or burner only works on certain knob settings
• Designed to match OEM fit and function for straightforward replacement

• Turn off gas supply and electrical power before starting any work
• Use appropriate hand tools; avoid forcing fittings or connections
• After installation, check all gas connections for leaks with a soap solution or approved leak detector

This gas valve controls fuel flow to the range/oven burner, restoring reliable ignition and heat control. Precision operation helps maintain even cooking and safe burner performance when the valve is faulty. What it does:

• Regulates gas flow to the burner assembly so the oven/range heats correctly
• Works with the appliance's safety and ignition systems to enable reliable lighting
• Commonly replaced for symptoms like no heat, intermittent ignition, or gas smell during operation
• Designed as a direct-fit valve for compatible Whirlpool-built ranges using Copreci 16k valves

• Turn off gas supply and disconnect power before attempting service
• Follow the appliance service manual for proper valve removal and gas line reconnection
• Check all fittings for leaks after installation and before returning the appliance to service

This water inlet valve controls water flow to the refrigerator's dispenser and ice maker so you get reliable ice and chilled water. Replaces a failed valve to restore proper water supply and prevent interruptions. What it does:

• Opens and closes to route household water to the dispenser and ice maker when activated
• Helps ensure proper filling of the ice maker and water dispensing
• Can cause no water from the dispenser or ice maker if failed or clogged
• May leak or drip when seals or diaphragms wear out

• Disconnect power and shut off the water supply before starting work
• Replace only with the exact part number; inlet/outlet fittings match your unit
• Inspect supply lines and electrical connectors for damage; tighten or replace as needed

This replacement gas valve regulates gas flow to the appliance's burner assembly so the unit can ignite and reach proper heat. Use this exact-fit valve to restore reliable ignition and consistent heating performance. What it does:

• Controls and meters gas flow to the burner assembly for safe ignition and stable flame
• Replaces a failed or leaking valve to stop intermittent or no-heat operation
• Addresses symptoms such as burners not lighting, weak or inconsistent flame, or the appliance failing to heat
• Works as the original-style valve designed for the specified 210 / 15,000 configuration

• Turn off gas supply and electrical power before starting work; follow local codes
• After installation, check all connections and test for gas leaks with a proper leak detector or soapy-water test
• Do not attempt to disassemble or repair the valve; replace if defective