Range / Cooktop / Oven Wire, Harness, Power Cord

Replacement burner wire harness that restores the ignition wiring connection for a gas range surface burner, helping re-establish consistent sparking and reliable burner ignition for safe cooking operation. What it does:

• Provides the electrical connections between the burner igniter/spark electrode and the range's ignition module/control.
• Replaces damaged, cut, or frayed wiring that can cause no-spark, intermittent ignition, or continuous clicking at the burner.
• Routes and secures ignition wires to keep connections stable and reduce heat/rub-related failures.
• Helps the ignition system deliver consistent sparks so burners light reliably.

• Disconnect electrical power and shut off the gas supply before beginning any service.
• Compare the new harness to the original; transfer and reconnect terminals one-to-one and secure any routing clips or fasteners.
• Route wires away from hot surfaces and sharp edges; avoid stretching or pinching the harness.

A replacement wire harness assembly that restores reliable electrical connections between control components. Replacing a damaged harness can stop intermittent operation and restore power or signals to affected systems so controls and features work properly. What it does:

• Routes power and signal between the control and appliance components to enable normal operation.
• Replaces frayed, broken, or burned wiring that can cause intermittent function or loss of power to parts.
• Helps resolve unresponsive controls, features that stop working, or faults caused by open/shorted wiring.
• Eliminates related error codes or unexpected shutdowns when the harness is the root cause.

• Disconnect power (unplug or shut off breaker) before inspecting or replacing the harness.
• Document connector locations and routing with photos before removal; match routing and connector orientation on reassembly.
• Make sure connectors are fully seated and wires are secured away from moving parts and heat sources.

High-voltage harness routes power between high-voltage components in a microwave oven, restoring safe electrical connections and preventing intermittent operation or arcing when replacing a damaged or burned wiring assembly. What it does:

• Connects the microwave's high-voltage components to maintain proper power flow.
• Failing or damaged harnesses can cause no-heat, intermittent heating, arcing, burning smell, or blown fuses.
• Replaces frayed, melted, or corroded high-voltage wiring that risks shorting or unsafe operation.
• Designed to restore original electrical routing and secure connector fit for reliable operation.

• Disconnect power and unplug the appliance before servicing. Ensure the high-voltage capacitor is properly discharged—do not attempt service without this step.
• Inspect connectors, insulation, and routing; replace damaged clips or retainers and secure wiring away from sharp edges and moving parts.
• Follow the wiring diagram for correct connections.
• Never operate the appliance with covers or safety panels removed.

This harness burner box is the electrical ignition harness assembly that routes power and signals to the range/stove burner valves and igniters, restoring reliable spark and control at the burner module. What it does

• Routes ignition and valve control wiring between the cooktop control module and individual burner valves/igniters.
• Enables spark ignition and proper valve response so burners light when controls call for flame.
• Commonly replaces worn or damaged harnesses that cause intermittent ignition, no-spark, or unresponsive valves.
• Keeps wiring organized and secured inside the burner box to prevent chafing or shorts.

• One harness burner box assembly as shown.

• Disconnect electrical power and shut off gas supply before starting work.
• Handle connectors carefully; match wire connectors and routing to the original harness during replacement.
• Inspect surrounding terminals and components for heat or corrosion damage and replace if needed.

This genuine-style replacement power cord restores electrical connection to compatible appliances, letting the unit receive mains power safely. Use it to replace frayed, damaged, or missing cords and stop intermittent or no-power issues. What it does:

• Carries mains power from the wall outlet to the appliance
• Replaces damaged or worn cord that causes intermittent power or no power
• Eliminates exposed wires, melting, or visible cord damage that can be a safety hazard
• Restores secure strain relief and connector fit when original cord is failing

• Disconnect the appliance from power before starting any work
• Follow the appliance service manual for access and wiring; correct terminal connections
• Tighten strain relief and secure wiring to prevent pinching or chafing

This replacement power cord restores the appliance's main AC connection so it can receive power safely. Use this cord when the original cable is frayed, cut, melted, or otherwise damaged to prevent intermittent power or electrical hazards. What it does:

• Replaces the appliance's factory power cable to restore reliable electrical connection.
• Transmits mains power from the outlet to the appliance's internal wiring and controls.
• Addresses symptoms such as no power, intermittent power loss, visible cord damage, or burn/melt marks at the cord or plug.
• Helps prevent electrical arcing or shorting caused by damaged insulation or exposed conductors.

• Disconnect the appliance from power at the breaker or unplug before starting any work.
• Verify the cord matches the appliance's connector and routing; do not modify cord ends or splices.
• Secure all strain reliefs and terminal connections per the appliance's service instructions.

This harness burner box is the wiring assembly that routes power and ignition signals to a gas range's burner box, restoring reliable electrical connections for safe burner ignition and consistent operation. What it does:

• Routes power and ignition signals between the control valve, igniters and burner box components
• Provides factory-style connector interfaces to maintain correct electrical paths
• Helps resolve intermittent or no-ignition issues caused by damaged or loose wiring
• Reduces risk of arcing or shorting from frayed or burned harness wiring

• Always disconnect electrical power and shut off the gas supply before servicing
• Handle connectors gently and seat each connector fully to avoid loose connections
• Inspect surrounding insulation and connectors for heat or burn damage and replace if needed

This harness burner box is the wired ignition assembly that routes spark and power to a cooktop's burner valves and igniters, restoring reliable ignition and consistent burner operation. What it does

• Delivers spark and electrical connection to surface burner igniters and gas valve controls.
• Replaces damaged or frayed wiring that can prevent burners from sparking or lighting.
• Restores proper routing and secure connections to reduce intermittent ignition failures.
• Intended for use with compatible gas range cooktops that use a burner-box ignition harness.

• Designed for experienced DIYers; disconnect power and shut off gas before starting.
• Inspect mating connectors, igniters and valves while installing; replace any visibly damaged components.

A replacement power cord kit that restores the electrical connection for a freestanding range or wall oven, letting the appliance receive mains power safely and reliably. What it does:

• Provides the main AC connection between your appliance and household power
• Replaces damaged, frayed, or burned cords that cause loss of power or intermittent operation
• Helps prevent arcing or poor contact from worn wiring or terminals
• Used when plug, cord insulation, or strain-relief components are defective

• Disconnect appliance from power at the breaker before beginning work
• Inspect terminal block and wire connections; tighten to manufacturer torque if specified
• Route cord and secure strain relief per appliance cabinet opening to avoid pinching

This single-conductor replacement wire restores an electrical connection between components in compatible Whirlpool appliances. It's a straightforward part used when a damaged or broken wire prevents normal operation. What it does

• Carries electrical current between terminals or components to enable operation.
• Replaces frayed, broken, or heat-damaged wiring that can cause intermittent or no power to a component.
• Common symptom: affected circuit or component won't power on or works sporadically.
• Helps re-establish a reliable connection when the original wire is corroded or has a broken conductor.

• Disconnect power (unplug appliance or shut off circuit breaker) before starting any repair.
• Use proper wire connectors/crimping techniques and ensure secure, insulated connections.
• Verify correct routing and strain relief to avoid contact with moving parts or heating elements.

This wiring harness assembly routes power and signals between the appliance's controls and components to restore reliable electrical connections. Replaces a damaged or worn harness to help fix intermittent power, non-responsive controls, or component failures. What it does

• Carries power and control signals between the control board, motors, switches, sensors, and other components.
• Restores proper electrical connections when wires are cut, burnt, or internally broken.
• Can stop intermittent operation, flickering lights, or components that don't receive power.
• Prevents arcing and short circuits caused by frayed or exposed wiring when replaced promptly.

• One wiring harness assembly as shown

• Disconnect power to the appliance before starting any repair to avoid shock or injury.
• Handle connectors gently; match connector shapes and keyed tabs to ensure correct seating.
• Route and secure the harness to original clips and channels to prevent chafing and interference with moving parts.

This replacement power cord restores electrical connection to your appliance so it powers on safely and reliably. Designed as a direct-fit electrical cord to replace damaged, cut, or worn factory cords. What it does

• Provides the primary AC power connection from the wall outlet to the appliance.
• Replaces frayed, cracked, or damaged cords that can cause intermittent power or safety hazards.
• Helps resolve no-power or intermittent-power symptoms when the cord is the root cause.
• Restores a secure connection at the appliance and outlet when properly installed.

• Disconnect power at the breaker or unplug the appliance before starting any work.
• Route the cord through the appliance's strain relief and secure all wiring connections per the appliance's wiring diagram.
• Use insulated tools and avoid pinching or sharp bends in the cord; replace strain reliefs if damaged.

This ground wire provides a safe chassis connection to restore proper grounding and reduce shock and electrical-fault risk. It replaces a frayed, corroded or missing ground lead to help keep the appliance electrically safe. What it does

• Connects the appliance chassis to the grounding system to prevent stray voltage on metal surfaces
• Restores a secure ground path if the original wire is broken, loose, or corroded
• Helps stop intermittent power faults or nuisance tripping caused by a compromised ground
• Addresses symptoms like visible wire damage, loose ground connection points, or grounding-related electrical issues

• One ground wire

• Always disconnect power (unplug or shut off the circuit breaker) before starting work
• Attach the ring/terminal ends to the designated chassis ground screw and the equipment ground point
• Route the wire away from moving parts, heating elements, and sharp edges; secure with existing clips or fasteners
• If terminal hardware is missing or damaged, replace with equivalent OEM-style fasteners and torque to specification

This genuine wire harness routes electrical signals and power between components to restore proper operation and connectivity. It replaces damaged or frayed wiring to help eliminate intermittent power, control failures, or non-responsive functions. What it does:

• Carries power and control signals between appliance components to enable normal operation
• Replaces worn, burned, or broken wires and connectors that cause intermittent or no power
• Helps resolve issues like unresponsive controls, motors not running, or lights that won't turn on
• Preserves factory routing and connector fit for a secure, reliable connection

• One complete wire harness as shown

• Disconnect power at the breaker or unplug the appliance before inspecting or replacing the harness
• Compare connectors and wire colors to the old harness to ensure correct fit before installing
• Secure wires along original routing and fasten any clips or ties to prevent rubbing or pinching

This wire harness assembly routes power and signals between major components to restore electrical connection and reliable operation. It replaces a damaged or frayed harness to help eliminate intermittent power, no-starts, or lost control functions. What it does:

• Connects power and control circuits between the main control and other components
• Restores reliable electrical continuity when wiring is damaged, burned, or corroded
• Helps resolve symptoms such as intermittent operation, appliances that won't start, or components that receive no power
• Prevents shorting or arcing caused by exposed or broken wires when properly installed

• Disconnect the appliance from power (unplug or turn off the circuit breaker) before beginning work
• Handle connectors gently; match keyed connectors when reassembling to avoid miswiring
• Inspect mating terminals and housings for damage; replace if terminals are burned or corroded

This wire harness is the OEM-style electrical assembly that routes power and signals between a dryer's control components for reliable operation. It replaces damaged or burnt wiring to restore proper electrical connections and functionality. What it does:

• Carries power and control signals between the appliance's control board, motor, heater, and other components
• Restores lost or intermittent electrical connections caused by frayed, pinched, or burned wires
• Helps eliminate faults or error codes tied to open or shorted wiring paths
• Matches the OEM routing and connector types for a direct-fit replacement when compatible

• Disconnect power before starting — verify the appliance is fully de-energized.
• Take photos or label connectors before removal to ensure correct reassembly.
• Inspect mating connectors and terminals; replace any that are damaged or corroded.