We use cookies and similar tools for site analytics and advertising. By using our site, you agree to this. See our Privacy Policy for details. Do Not Sell or Share My Personal Information
Need Help?
Call
This is a monitor or interlock switch that detects whether the microwave door is properly closed before allowing the unit to operate. It is a safety device that shuts off microwave power if the door is open or if other door switches malfunction. Replace this switch if the microwave does not start, runs with the door open, or blows a fuse when the door is closed.
The first symptom was our microwave would continue to run after the time was up. The light would go out, the turn table would stop but you could still hear the microwave running and whatever was in it would continue to cook. The only way to stop it was to open the door. It was intermittent at first but eventually it would always run no matter what as long as the door was closed. Several other posts referenced these switches as the problem. I just replaced both and problem gone. It turns out... Read more
Fix a burner stuck on high or an indicator light that won't turn off. This infinite switch controls heat settings on electric range burners. DIY-friendly repair.
1. Went online where I watched video about heat control for this Maytag. I then found AppliancePartsPros using Google. I ordered the part and In three days the part arrived. I installed the part and now the problem has been corrected. Read more
Burner stuck on high or won't heat? This triple burner switch restores proper temperature control. Many DIYers report a 5-minute fix for this issue.
I replaced the energy regulator. Read more
Burner won't turn off or stays on when set to off? This surface burner infinite switch controls heat levels. Takes 10-15 minutes to replace.
Replaced switch! Easy.... Read more
The Infinite Heat Switch Kit is an OEM part for GE ranges and cooktops. This kit is essential for controlling the temperature of the burners on your range or cooktop, allowing you to adjust the heat level from low to high.
Causes of damage to the infinite heat switch can include normal wear and tear from frequent use, electrical issues such as short circuits or power surges, and physical damage from cleaning or impact.
Symptoms of a bad Infinite Heat Switch include:
This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.
I replaced all 3 remaining burner controls because they were all original (mid 1970s GE electric range w/coil burners), and one of the controls occasionally made arcing sounds when cycling the burner on and off. If a control is making odd noises - more than just a quiet metallic clicking as it cycles - it should be replaced. I'm assuming you have experience with the tools needed and can do simple mechanical assembly or disassembly, but have not previously worked with electrical equipment of... Read more
Fix burners stuck on high or not responding to temperature adjustments. This range infinite switch restores precise heat control. DIY-friendly repair.
After removing the top rear access panel, I took as-built photographs of the two components to be replaced showing all wires, connectors and screws! The Energy Regulator for the front left burner was replaced first, noting the orientation before pulling off the knob, and removing the retaining screws. I used long nose pliers to gently remove one lead at a time and reconnect to the new regulator. Checked orientation against the photo, reinstalled regulator and knob. Main PCB Assembly was... Read more
The Infinite Control Switch is an OEM part for Whirlpool ranges and cooktops. This part allows for precise adjustment of the heat level, enabling users to achieve the perfect temperature for various cooking techniques, from simmering to boiling.
Causes of a bad Infinite Control Switch can range from electrical issues, such as short circuits or worn contacts, to mechanical failures within the switch itself.
Symptoms of a malfunctioning Infinite Control Switch include:
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
Replaced the switches. Read more
Fix a microwave that won't start or stops mid-cycle with this door interlock monitor switch. Ensures safe operation when door closes. DIY repair.
Removed and replaced 3 door switches and mounting bar that holds switches plastic gets brittle with age and each switch comes out slightly different from each other, the chances of breaking a mounting pin is very easy. care should be taken when snapping mounting bar back into place to insure top latch and bottom latch locate properly insure bar is proper aligned when tightening screws their is free play in mounting bracket that could affect door properly engaging switches. NOTE that their are... Read more
Burner won't ignite or sparks intermittently? This spark ignition switch and harness assembly restores reliable ignition. Moderate DIY repair.
First off thanks AppliancePartsPro.com... Another project in the books... I ordered a new switch harness and spark module because I just decided the why not do them both. They arrived very promptly, uses very simple tools most people have I would think. After unplugging it and shutting off the propane. I removed valve knobs. Then the burners with a nut driver and two sizes of sockets. The stove top and valve cover six Philips head screws. Gained complete access to the stove top. Removed... Read more
Fix burners that won't turn off, stay on high, or turn on by themselves. This surface element switch restores safe temperature control. 15-minute DIY fix.
We sent an email to AppliancePartsPros.com asking for their help in fixing our range. We gave them the model number (NE58F9500SS) of our Samsung Electric Range and told them about the faulty/dangerous two dual burners. We hated to get close to the range because the burners would turn on if you barely brushed by the range or if you would reach across it and accidentally touch the burner knobs all of a sudden you would feel heat or just see the light indicating the burner was on. We were... Read more
Top burner won't cycle temperatures or respond? This range burner control switch restores reliable heat regulation. Direct-fit replacement for electric and gas ranges.
Replaced burner control switch Read more
Burners won't light or igniters click constantly? This igniter switch and wiring harness assembly restores spark ignition on gas range surface burners.
Replacing the bad harness switches with the new set fixed the problem. Read more
If your burner won't heat, stays on high, or only works on low, replace the infinite switch. Simple 20-minute DIY repair with just a screwdriver.
Replaced the front burner switch with this switch. Works good as new now. Read more
Fix burners that won't spark or click. This igniter switch assembly restores gas ignition. Moderate DIY repair with video guide available.
Thanks, I’ follow the instructions on YouTube and my repairs was completed. Read more
Fixes burners that won't heat, stay on high, or make clicking sounds. Controls temperature settings on electric cooktops. Moderate DIY repair.
Put in a new infinite switch behind the knob to control temp level. Read more
Fixes burner stuck on, no low heat, or burner not heating. Controls temperature levels on electric range surface burners. Moderate DIY repair.
Switches needed to be replaced. Make note of where each screw comes from. They were not all the same. To remove the front panel and get to the switches, you have to partially remove the cook top. Removed 5 screws from the back to release the cooktop. Slid the cooktop back far enough to expose screws holding on the front panel. Removed 4 screws from the top and 6-8 from the bottom (opened the oven door to get to the bottom screws). Removed screws from the front panel holding the switch in... Read more