Range Latch, Catch, Lock Parts

This latch assembly secures and releases the oven door as designed, including during self-clean on many models. Replacing a worn latch restores proper door engagement so cycles start reliably and the door locks when required.

• Engages the door strike to lock and unlock the door
• Supports the self-clean safety interlock on applicable ranges
• Helps resolve issues like a door that won't lock/unlock or a latch that sticks/feels loose
• Clears control errors related to door lock status

• Disconnect power (and gas, if applicable) and allow the oven to cool completely
• Access the latch from the control area or beneath the cooktop/top panel, per model
• Note spring/linkage routing; transfer reusable hardware and align the latch with the door strike
• After reassembly, hand-check smooth latch movement and verify lock/unlock operation

This lid switch actuator engages the washer's safety switch when the lid is closed so cycles can start and spin as designed. Replace a broken or missing actuator to restore proper lid switch engagement and reliable operation.

• Engages the lid switch when the lid is closed to enable agitation and spin
• A worn, cracked, or missing actuator can cause the washer not to start or to stop before spin
• Intermittent operation that changes when pressing on the lid often indicates misalignment
• Lack of an audible "click" from the lid switch can point to a faulty actuator or alignment

• Disconnect power before servicing; do not work on a live appliance
• Access the lid/switch area per your model's service procedure
• Remove the damaged actuator and install the new part, securing as designed
• Before reassembly, close the lid to ensure the switch clicks and engages properly

This motor drives the fan or mechanism in your cooking appliance to move air as designed. Replacing a worn or seized motor restores proper airflow and quieter operation for consistent baking, cooling, or venting performance, depending on model.

• Powers the appliance's fan or drive to circulate air or move exhaust
• Helps maintain even temperatures or ventilation during operation
• Replaces a noisy, slow, or non-spinning motor
• Common signs: fan won't run, weak airflow, humming/grinding noise, overheating, or a tripped breaker

• Disconnect power at the breaker; shut off gas supply for gas models
• Access location varies by model; remove the necessary panels to reach the motor
• Note wiring and rotation; transfer any brackets, grommets, or the fan blade from the original, if required
• After installation, verify smooth, quiet operation and correct airflow

This latch and handle assembly engages the oven's door lock when you move the lever, allowing self-clean cycles to start and complete safely. Replacing a worn or broken latch/handle restores smooth locking and proper door interlock function.

• Provides the manual lever and latch mechanism that locks the oven door for self-cleaning
• Interfaces with the door lock switches to signal locked/unlocked status to the control
• Common symptoms: self-clean won't start or end, door won't lock/unlock, lever is loose/stuck/broken, or a door lock/latch error is displayed
• Restores safe door security during high-heat cleaning

• Disconnect power at the breaker before servicing; allow the oven to cool completely
• Access is typically from the control panel/top or rear, depending on model—take photos of linkage and any wiring for reference
• Move connectors and mounting hardware over one at a time to maintain orientation
• After reassembly, check lever travel and the door locks/unlocks before starting a clean cycle

This door latch secures the appliance door and signals the control that it's safely closed. Replacing a worn or broken latch restores reliable door closure and proper cycle operation. What it does:

• Holds the door closed and aligned during use
• Engages the door strike to complete the door/lock switch circuit
• Resolve issues such as: door won't latch or pops open; cycles won't start; intermittent "door open" messages; needing to press/hold the door to run

• One door latch

• Disconnect power before servicing
• Access is typically from the door/front panel; note screw locations and latch orientation
• Transfer any mounting hardware from the original latch if needed
• After installation, verify smooth latch engagement with the strike and run a test cycle

Replacement motor that restores mechanical drive or airflow in select Frigidaire appliances. Installs in place of the original motor to help return normal rotation, tumbling or fan operation. What it does:

• Drives rotating components (drum, tumbler, agitator or fan) depending on application.
• Helps restore normal spin, tumble or airflow when the original motor fails.
• Common symptoms: appliance won't start or spin, weak/uneven rotation, loud humming/grinding, or reduced airflow.
• Direct-fit replacement designed to match original mounting and electrical connections for specified models.

• Disconnect power (and water if applicable) before beginning any work.
• Avoid pulling on wires; reconnect all harnesses and secure mounting fasteners per OEM instructions.

This rear latch assembly secures the dryer door so the appliance can latch and run properly. It replaces a worn or broken rear latch to restore reliable door closure and help the dryer start and stay closed during cycles. What it does:

• Secures the dryer door to engage the door switch so the dryer will start
• Keeps the door closed during operation to prevent interruptions mid-cycle
• Replaces a broken, bent, or worn latch that prevents the door from latching
• Commonly used when the dryer won't start, stops unexpectedly, or the door won't stay closed

• Disconnect power (unplug or switch off breaker) before beginning any work
• Installation may require removing the dryer top or front panel; follow the model's service instructions
• Handle panels and metal edges carefully to avoid cuts
• After installation, verify the door latches securely and the dryer starts before reassembling all panels

This oven door latch assembly locks the door during self-clean and reports lock status to the control. Restores proper door locking and unlocking so bake and clean cycles can run safely and without interruptions. What it does:

• Secures the oven door during self-clean and when commanded by the control
• Provides locked/unlocked position feedback to the electronic control
• Helps resolve issues such as a door that won't lock or unlock
• Can address self-clean cycles that won't start or complete and lock-related error messages

• 1 latch assembly

• Disconnect power at the breaker and allow the oven to cool completely
• Access varies by model; you may need to pull the unit and remove the rear or top/control panel
• Photograph wire connections and linkage before removal; transfer any mounting hardware from the original
• After installation, test the lock operation before final reassembly

This oven door latch secures the door to the oven frame as designed, restoring safe, reliable door locking. Replacing a worn or damaged latch helps ensure proper operation and prevents cycles from being interrupted by a door that won't latch.

• Locks and releases the oven door as required by the appliance's design
• Helps the oven operate safely by ensuring positive door engagement
• Can help resolve issues like a door that won't lock/unlock or a clean cycle that won't start due to latch problems
• Replaces bent, broken, or sticking latch mechanisms

• Disconnect power at the breaker before servicing; allow the oven to cool completely
• Access location varies by model
• Take photos of spring/linkage orientation and transfer any reused components from the original latch
• After installation, verify the door opens, closes, and locks/unlocks smoothly before running a cycle

A small rubber bumper that cushions and protects appliance doors, drawers or panels to reduce noise and prevent hard contact. Replaces worn or missing bumpers to restore a snug, quiet close. What it does:

• Provides a soft buffer to stop doors or drawers from banging into the cabinet or frame
• Reduces vibration and rattling during operation
• Helps doors and panels sit properly when closed
• Simple, non-electrical part — no wiring or adjustment required

• One replacement bumper

• Inspect the mounting hole or surface; clean debris before installing
• Press the bumper into the hole or onto the surface until fully seated; use a blunt tool if needed for tight fits
• Disconnect power to the appliance first and follow OEM instructions
• Remove old adhesive before installing the new bumper

This door opening lever is the replacement release lever that lets the appliance door latch open and close smoothly, restoring reliable door-opening action and making everyday use easier. What it does:

• Replaces a worn, broken, or cracked lever that releases the door latch.
• Lets the door latch release properly so the door opens without excessive force or sticking.
• Works with the latch assembly to help ensure the door closes securely and operates smoothly.
• Addresses common symptoms such as a loose or unresponsive door handle, difficulty opening the door, or a lever that snaps.

• Disconnect power (and water, if applicable) before attempting any repair.
• Access may require removing the door trim or outer panel; basic hand tools are typically needed.
• Inspect surrounding latch components while replacing the lever and replace any damaged hardware.

The Latch Ovn is an OEM part for GE ranges. It functions as the latch mechanism that secures the oven door in the closed position during cooking.

The latch oven is responsible for safely and securely holding the oven door shut while in use. It allows for controlled opening and closing of the door to facilitate easy access inside the oven cavity.

Causes of a bad latch oven can include wear and tear over time, failure of mechanical components within the latch mechanism, or damage from overtightening or forced opening/closing of the oven door.

Symptoms of a bad latch oven include:

• The oven door not latching fully or securely in the closed position
• Difficulty opening or closing the oven door
• The door popping or springing open unexpectedly

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This replacement latch assembly secures the refrigerator or freezer door to ensure proper closure and reliable operation. It restores the door catch so the appliance can maintain an effective seal and help prevent cooling loss. What it does:

• Secures the door to keep it closed and aligned
• Replaces a broken, bent, or worn latch that prevents proper latching
• Helps reduce warm air entry caused by a door that won't stay shut
• Works as the mechanical catch that engages the door striker

• Disconnect power (unplug appliance) before servicing to avoid shock or injury.
• Remove the inner door panel or access trim as needed to reach the latch; keep screws and fasteners organized.
• Align the latch with the door striker and tighten screws securely without over-torquing.
• Test door operation several times after installation to ensure proper engagement and seal.

This maintop strike is the small latch plate the cooktop engages with to stay secured and aligned. Replacing a bent or missing strike restores a snug-fitting main top and proper engagement with the latch mechanism.

• Provides the engagement point for the main top's latch mechanism
• Helps keep the cooktop seated and aligned to reduce movement and rattling
• Can correct issues like the top not staying down or visible gaps at the front edge
• Supports proper actuation of any associated latch/safety switch, when applicable

• Disconnect power (and gas, if applicable) and allow the appliance to cool before servicing
• Open/raise the cooktop per the unit's design and support it safely
• Remove the old strike and align the new strike in the same position; reuse existing mounting hardware if applicable
• Tighten fasteners securely and test latch engagement before restoring power

Replacement latch keeper for the dryer door latch assembly that secures the latch and keeps the door closed during operation. Restores reliable door engagement to help the appliance start and complete cycles. What it does:

• Secures the door latch so the dryer door stays closed during operation.
• Aligns with the latch mechanism to maintain proper door engagement.
• Common symptom: dryer door won't latch or feels loose, causing the cycle to not start or stop unexpectedly.
• Replaces worn or broken keeper pieces that allow rattling or misalignment.

• Disconnect power (unplug electric or shut off gas and breaker) before servicing.
• Access with basic hand tools; remove the door or front panel as needed to reach the keeper.
• Install carefully to avoid cracking surrounding plastic; do not force parts into place.
• After installation, verify the door closes securely and the dryer starts through a test cycle.