Refrigerator Grille

This grille is a cosmetic cover that attaches to the appliance to finish the opening and help protect internal areas. Replacing a damaged or missing grille restores a clean appearance and a secure, proper fit. What it does:

• Attaches at the designated location to provide a finished look
• Helps shield underlying components and keep debris out
• Designed to fit securely using existing clips or screws
• Common symptoms: cracked or warped plastic, broken tabs, loose fit, or missing piece

• 1 grille

• Disconnect power to the appliance (and shut off utilities if applicable) before servicing
• Remove any retaining screws or clips; gently release locking tabs to avoid damage
• Transfer reusable mounting hardware from the old grille if required
• Align and secure the grille; do not overtighten fasteners

This replacement toe grille installs at the bottom front of the refrigerator. The 30-inch black kickplate finishes the look and helps protect and ventilate the condenser area. Replace a cracked or missing grille to restore appearance and airflow.

• Covers the lower front opening and directs air through the condenser vents
• Shields base components from bumps and debris during everyday use
• Provides a clean, finished look along the floor line
• Common signs of failure: cracked or warped grille, broken mounting tabs, won't stay attached, or missing piece

• Disconnect power before servicing
• Remove the old grille by releasing retaining clips or removing screws; save any reusable hardware
• Align the new grille and snap into place or reinstall screws—do not overtighten
• Keep ventilation slots clear after installation

This 30-inch toe grille covers the lower front of the refrigerator, completing the built-in look while allowing proper ventilation to the condenser area. Replace a cracked or missing kickplate to protect components and refresh the appliance's appearance. What it does:

• Covers the base/kick area at the front of the refrigerator
• Provides venting to help air flow through the condenser compartment
• Shields internal components from bumps and debris
• Restores a clean, finished exterior when the original is damaged or lost

• 1 toe grille (30 in)

• Disconnect power and wear cut-resistant gloves before starting
• Remove existing mounting screws or release retaining tabs; save hardware for reuse
• Align tabs/clips with cabinet slots and press or fasten the grille until fully seated
• Ensure vents are unobstructed and doors open/close without interference after installation

This front grille replaces the toe-kick panel at the base of the appliance. It helps protect the condenser area from debris and provides a finished look across the bottom front of the unit.

• Covers and protects the lower front opening and condenser area
• Helps direct airflow to the condenser for proper cooling performance
• Restores a clean, finished appearance when the original grille is damaged or missing
• Common signs: cracked or broken grille, missing panel, or difficulty keeping the lower area clear of debris

• Unplug the appliance and turn off water supply before starting
• Open doors and remove any screws or clips securing the grille; pull to release
• Align new grille with mounting points; snap or screw into place
• Check for secure fit and proper airflow clearance

This 42" toe kick is the lower front panel that restores the finished appearance at the base of your refrigerator while protecting the kickspace. It replaces a cracked, dented, or missing grille to tidy the appliance's look. What it does:

• Covers the lower front of the appliance to hide leveling hardware and internal components.
• Protects the kickspace from dirt, pet access, and accidental scuffs.
• Restores the refrigerator's factory appearance after damage or loss of the original panel.
• Helps maintain proper clearance and airflow pathways designed for the model.

• Follow the refrigerator service manual for removal and installation steps; disconnect power if work requires removing panels near electrical components.
• Installation typically involves removing the old kick panel and aligning the replacement into factory clips or brackets.
• Keep any existing mounting hardware and use common hand tools.

This kickplate grille mounts across the bottom front of the refrigerator. It restores a finished look and helps protect the machine compartment while allowing proper airflow through the condenser area.

• Covers the lower front opening to hide and shield internal components
• Vents air to support proper condenser airflow
• Replaces a damaged, cracked, or missing kickplate
• Common symptoms: broken tabs, grille won't stay attached, visible damage, missing piece

• Disconnect power before servicing
• Open doors to clear the grille; remove the old piece by releasing clips or removing screws
• Align the new grille with the mounting points and snap or fasten into place
• Ensure the grille sits evenly and doesn't interfere with door swing or airflow

The Grille-Front is an OEM component specifically designed for Whirlpool refrigerator cabinet fronts. It allows for air circulation while protecting internal refrigeration system components. Proper grille functioning keeps components running cool and efficient.  

Symptoms of a bad grille can include:

• Parts of the grille cracking, loosening, or detaching
• Reduced airflow causing elevated temperature readings inside
• Components overheating, leading to premature failures

Causes related to physical impacts, such as kids' toys or vacuum cleaners striking the grille. Direct sun exposure can also cause material degradation over time.

This OEM Whirlpool part is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This refrigerator kickplate grille mounts across the lower front of the cabinet to cover the machine compartment while allowing proper airflow. Replacing a broken or missing grille restores a clean finish and helps keep debris away from internal components.

• Covers the lower opening and helps shield the condenser area from bumps and debris
• Helps direct air through the base for proper ventilation
• Restores a clean, finished appearance across the bottom front
• Typical symptoms: cracked or scuffed grille, broken mounting tabs, loose or won't stay attached, missing

• Disconnect power and wear work gloves to avoid sharp edges
• Open doors; on many models, pull the grille straight out to release spring clips. If screws are used, remove them from the base rail
• Align tabs/clips and snap or fasten the grille into place
• The grille is secure and clear of door swing and air inlets

This grille base is the lower front kick grille that restores the refrigerator's finished look and helps direct airflow at the appliance base. It replaces a cracked, broken, or missing lower grille for a secure fit and neat appearance. What it does:

• Covers and protects the refrigerator's lower front area and internal components from debris.
• Helps channel airflow across condenser/vent openings to maintain proper ventilation.
• Replaces damaged or broken grille pieces that can cause rattling or poor fit.
• Restores the appliance's finished look by replacing warped or discolored trim.

• Disconnect power to the appliance before beginning any service.
• Handle edges carefully; align clips/tabs with mating slots for a secure fit.
• Some models use snap-in tabs or screws—retain hardware and reattach in the original locations.
• If tabs or mounting points are broken, inspect surrounding trim for additional damage.

This fan grill assembly covers and directs airflow for the evaporator fan, helping protect the fan and maintain proper circulation inside the compartment. It replaces a cracked, broken or missing grill to restore safe airflow and component protection. What it does:

• Protects the evaporator fan from debris and prevents contact with the spinning blades
• Directs airflow for consistent circulation across the evaporator coils
• Can reduce rattling or vibration caused by a damaged or loose grill
• Helps avoid airflow restriction that contribute to cooling issues

• Disconnect power to the appliance before any service to avoid shock or injury
• Typically installs behind an interior access panel; gentle trim removal may be required
• Inspect mounting tabs and clips; replace any damaged fasteners for secure fit
• Handle plastic parts carefully to avoid cracking; do not overtighten screws

This lower kickplate grille covers the refrigerator's toe-kick opening to protect components and finish the appliance's front. It restores appearance and maintains proper airflow through the cabinet bottom. What it does:

• Covers and protects the lower front area and components behind the toe kick
• Helps direct airflow under the cabinet where condenser/venting passages are located
• Replaces cracked, broken, bent, or missing lower grille pieces that leave the opening exposed
• Restores a finished look to the appliance front

• One lower kickplate grille

• Disconnect power to the appliance before starting any work
• Remove the old kickplate by releasing retained clips or fasteners, then align and secure the replacement
• Use gentle pressure to avoid bending the grille or damaging adjacent finishes
• Replace with OEM-specified hardware

This grill base is the lower kick grille assembly that supports and protects the appliance's lower front opening while keeping the unit's appearance finished. It restores proper airflow and a secure lower trim. What it does

• Replaces a cracked, bent or missing lower kick grille that can catch debris or look damaged.
• Helps maintain proper front trim alignment and keeps the space below the appliance covered.
• Reduces draft and prevents small objects from entering the area beneath the appliance.
• Restores original fit and appearance when the existing grill is loose or warped.

• Disconnect power to the appliance before beginning work.
• Typically fastens with a few screws or retention clips; use basic hand tools.
• Support the grille during removal to avoid scratching the finish or damaging adjacent trim.

This stainless steel 48 in toe kick replaces the lower front panel on compatible refrigerators to restore a clean, finished look and protect the base of the appliance from scuffs and dirt. Durable, visible finish matches stainless models. What it does:

• Covers the refrigerator kickspace for a finished appearance and to protect the lower cabinet area
• Helps prevent dirt, dust and small objects from entering the appliance base
• Restores damaged or dented front trim that affects the look of the appliance
• Works with existing mounting points and grille assemblies on compatible units

• Remove the existing toe kick/grille per your appliance service instructions before installing
• Align panel to factory mounting clips or screw holes and secure using original fasteners
• No electrical disconnection required for the toe kick itself, but follow safety procedures if working near powered components
• Handle with care to avoid scratches; use gloves and a soft surface during installation

This replacement grille covers the appliance's front vent opening to maintain airflow and protect internal components. It restores a clean, finished appearance and secure fit when the original grille is cracked, warped, loose, or missing.

• Directs airflow through the unit for proper ventilation
• Shields internal parts from debris and accidental contact
• Replaces a broken, warped, or missing grille
• Common symptoms include rattling, poor fit, visible cracks, or an exposed opening

• Disconnect power to the appliance before servicing
• Remove mounting screws or release retaining tabs; keep hardware for reuse
• Align the new grille with tabs or slots and secure without overtightening
• Restore power and confirm proper fit and clearance

The Grille is an OEM replacement part for Whirlpool refrigerators. It covers the gap between the bottom of the refrigerator and the floor, providing a clean and finished look to your kitchen. It helps protect the internal parts from dust and debris while also preventing small items from rolling underneath the appliance.

Symptoms of a bad toe grille include:

• Visible cracks or damage
• Discoloration or fading
• Missing pieces or gaps in the grille

A damaged or worn-out toe grille can occur due to regular use, accidental impacts, or general wear and tear over time. If you notice cracks, discoloration, or missing pieces on the toe grille, it may be time to replace it.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.