Refrigerator Wire, Harness, Power Cord

Replacement wire harness that restores electrical connections between the appliance control, power and components for reliable operation and correct signaling. Use this complete wiring assembly when damaged wires or connectors cause power or control issues. What it does:

• Routes power and signal conductors between the control board, switches, motors and sensors.
• Replaces damaged, frayed or melted wiring and broken connectors that can cause intermittent operation, no-start or control failures.
• Restores factory-style plug connections and routing to help prevent miswiring and shorts.
• Matches the original connector shapes and wire colors for straightforward replacement.

• Disconnect power (unplug or shut off breaker) before servicing to avoid shock or injury.
• Remove and replace the harness by disconnecting connectors at the control and components; handle connectors by the plastic bodies, not the wires.
• Route the harness along the original path and secure with existing clips or fasteners to prevent rubbing or heat exposure.

This wire harness routes power and signals between your appliance's control and components to restore reliable electrical connections. Replacing a damaged harness helps stop intermittent power, faulty controls, or non-starting appliances. What it does:

• Transfers power and control signals between main control, motor, and other components
• Replaces cracked, burned, or frayed wiring that can cause intermittent operation
• Helps resolve symptoms like appliance not starting, control lights flickering, or components losing power
• Restores secure connector fit where pins or terminals are loose or corroded

• Disconnect all power before beginning service to avoid shock or injury
• Take photos or label connectors before removing the old harness to ensure correct routing
• Inspect connectors and terminals for damage; replace harness if insulation or terminals are compromised
• Secure harness away from sharp edges, moving parts, and heat sources during reassembly

This wire assembly connects and powers the ice maker so it can cycle and make ice. It replaces a damaged or disconnected ice-maker harness to restore electrical continuity and reliable ice production. What it does

• Provides the electrical connections between the ice maker and the freezer wiring harness
• Restores power to the ice maker when factory wiring is frayed or broken
• Helps stop intermittent or complete ice-maker failure caused by damaged connectors or wiring
• Supports proper communication for fill and harvest cycles when installed correctly

• One wire assembly for the ice maker

• Disconnect power to the refrigerator before starting any repair
• Access may require removing freezer shelves/panels and the ice maker module per OEM instructions
• Match connector shapes and routing; avoid sharp bends or pinched wiring when installing
• After installation, restore power and run an ice-maker test cycle to verify proper operation

This control box wiring harness routes power and signals between the appliance control board and other components to restore reliable control operation and electrical connectivity. It helps resolve intermittent controls and lost function caused by damaged wiring. What it does:

• Connects the control board to switches, sensors and motors to enable normal control functions.
• Replaces damaged or frayed wiring that can cause intermittent operation or unresponsive controls.
• Addresses symptoms such as control panel not responding, random shutdowns, or error codes tied to wiring faults.
• Restores proper signal and power routing when connector damage or wire breaks interrupt circuits.

• Disconnect all power to the appliance before beginning any service.
• Compare the new harness to the original and follow factory connector positions and routing to avoid pin miswiring or chafing.
• Handle connectors gently and ensure all terminals fully seat; inspect mating connectors for damage before reconnecting.

This controller assembly is the main electronic control board that manages your appliance's cycles and user interface, restoring normal control when the original board fails. It replaces a faulty control module to help the unit operate reliably. What it does:

• Controls timing, cycles, and functions per user commands and sensor inputs
• Replaces malfunctioning or unresponsive control electronics that cause erratic operation
• Can resolve symptoms such as no power to controls, unresponsive buttons, or incorrect cycle behavior
• Works with existing wiring harnesses and display components when compatible

• Disconnect power before beginning work to prevent shock or damage
• Verify connector locations and orientation before removing the old board
• Handle the board by edges and avoid contact with circuitry to prevent static damage

This wire harness routes power and control signals between the appliance control and components to restore reliable electrical connectivity. It replaces damaged or burned wiring to help resolve intermittent operation and loss of function. What it does:

• Provides organized, insulated wiring to connect the control board to heaters, motors, sensors and switches.
• Restores continuity where frayed, pinched or burned wires cause faults or shorts.
• Common symptoms this can address: control panel unresponsive, appliance won't start, intermittent power or components not operating.
• Designed to follow factory routing and connector positions for correct fit and electrical function.

• Disconnect all power before replacing any wiring; verify power is removed at the breaker or unplug the appliance.
• Take photos or mark connector positions before removal to ensure correct reconnection.
• Avoid pulling on individual wires; remove and install at the connector housings to prevent terminal damage.
• If wiring is severely corroded or connectors damaged, inspect adjoining components and replace per service manual.

This wire harness routes power and signals between an appliance's control and electrical components to restore reliable connections and operation. Use it to replace a damaged or frayed harness that is causing power or control issues. What it does:

• Re-establishes secure electrical connections between controls, motors, switches and sensors
• Routes and organizes multiple wires to prevent shorts and chafing
• Replaces burned, frayed or broken wiring that can cause intermittent operation
• Helps resolve symptoms like no power to controls, unit not starting, or inconsistent function

• Disconnect all power (unplug or switch off circuit breaker) before servicing
• Label or photograph connector locations before removal to ensure correct reassembly
• Route harness to avoid pinch points and secure with original clips or ties
• Replace the harness and inspect mating components if you see melted connectors or damaged terminals

This power cord service assembly replaces a damaged or worn external cord to restore a safe electrical connection to the appliance. Designed as a direct-replacement assembly for service repairs, it helps return reliable power delivery. What it does:

• Provides the external electrical connection between the appliance and wall outlet
• Replaces frayed, cut, or damaged cords that can cause intermittent power or unsafe conditions
• Helps resolve issues where the appliance does not power on due to cord damage
• Restores proper strain relief and secure wiring at the appliance entry point

• Always disconnect power at the breaker or unplug the appliance before servicing
• Route the cord and secure strain relief per the appliance's service instructions

This genuine replacement wire harness connects and routes power and signals between components to restore proper electrical function and safe operation. Designed to match original wiring layout for a straightforward repair. What it does:

• Replaces a damaged or burned wiring harness to restore electrical continuity
• Restores power/signal paths that can stop intermittent operation or failures
• Helps eliminate arcing, shorts, or loss of function caused by frayed or broken wires
• Maintains correct routing to prevent chafing and overheating when installed correctly

• Disconnect all power (unplug appliance or switch off breaker) before starting work
• Handle connectors by the plug body, not the wires; ensure secure, full seating of terminals
• Route harness along original clips and channels to avoid pinch points or hot surfaces
• Replace any connector, terminal, or mounting hardware that is missing or damaged before powering on

This replacement power cord restores electrical connection to the appliance, providing a safe and reliable feed when the original cord is damaged or worn. It's a direct-fit wiring component meant for like-for-like replacement. What it does:

• Delivers AC power from the wall outlet to the appliance so it can operate.
• Replaces cords that are frayed, cut, melted, scorched, or have exposed wiring.
• Helps stop intermittent power, arcing at the plug, or appliances that won't power on due to cord damage.
• Works with the appliance's factory power inlet and strain-relief system when installed correctly.

• One replacement power cord.

• Always disconnect power at the breaker and unplug the appliance before installing.
• Match this cord to the appliance's original cord and connect using the existing terminals or connector; do not splice or alter wires.
• Use the proper strain relief and secure the cord to prevent pulling or chafing.

The Refrigerator Wire Harness Relay is an essential component designed to ensure your Samsung refrigerator operates smoothly and efficiently. This genuine OEM part guarantees a perfect fit and reliable performance, maintaining the integrity of your applianceGÇÖs electrical system. Crafted with high-quality materials, the wire harness relay effectively manages the flow of electricity within your refrigerator, preventing potential issues such as power disruptions or component failures. By replacing a faulty relay with this authentic part, you can restore your refrigerator's functionality and extend its lifespan without compromising on quality. Compatible with a wide range of Samsung refrigerator models, this wire harness relay simplifies the repair process, allowing for easy installation and seamless integration with your existing setup. Investing in this genuine OEM part not only enhances the performance of your refrigerator but also ensures peace of mind, knowing that your appliance is equipped with reliable and trusted components. Whether youGÇÖre a DIY enthusiast or seeking professional-grade parts, the Refrigerator Wire Harness Relay provides the dependable solution you need to keep your refrigerator running optimally.

This wire harness assembly connects electrical components to the appliance control, restoring proper signal and power routing for affected circuits. It replaces a damaged or worn harness to help components receive consistent electrical connection. What it does:

• Routes power and control signals between the control board and key components (motors, switches, sensors).
• Replaces frayed, burnt, or broken wiring that can cause intermittent operation or component failure.
• Helps stop symptoms like an appliance that won't start, components that work sporadically, or loss of functions tied to a damaged circuit.
• Provides factory-style connector fit to match original wiring junctions and routing.

• One wire harness assembly.

• Always disconnect power (unplug or shut off breaker) before servicing the appliance.
• Photograph or label connectors before removal to ensure correct reconnection.
• Route and secure the harness along the original clips and channels; avoid sharp edges or pinch points.

This wiring harness routes power and signal connections between components to restore proper electrical communication and operation. It replaces a damaged or worn harness to fix intermittent or failed electrical functions. What it does:

• Reconnects power and control circuits between components so systems can receive proper voltage and signals
• Commonly used when wiring is frayed, burned, pinched, or connectors are loose or corroded
• Can resolve symptoms like no power to a component, intermittent operation, or control not responding
• Restores secure plug-and-play connections when the original harness is damaged

• Wiring harness assembly

• Always disconnect power before replacing any wiring or electrical parts
• Inspect connector fit, wire routing, and strain reliefs; route harness the same way as the original to avoid pinching
• Make sure connectors are fully seated and any locking tabs engage
• If you see damaged connectors on the appliance side, repair those before connecting the new harness

This wire harness is the factory-style electrical assembly that routes power and signals between components to restore reliable operation. It replaces damaged or worn wiring and connector assemblies responsible for intermittent or lost power. What it does:

• Carries electrical power and control signals between appliance components
• Replaces frayed, burnt, or broken wiring that can cause intermittent operation
• Resolves symptoms such as the appliance failing to start, erratic control behavior, or intermittent power to components
• Ensures connectors are properly routed and joined to prevent shorts and unreliable connections

• Disconnect power (unplug appliance or switch off circuit breaker) before you begin
• Handle connectors gently; match connector shapes and pin counts before seating
• Route the harness following factory clips and channels to avoid heat or pinch points