Remington Log Splitter Parts

This silencer plate is used on a variety of outdoor lawn and garden machines to reduce the noise from the air intake. This molded plastic part sits on top of the carburetor and houses the air filter. It provides an added layer of noise muffling. Exposure to wind, rain, and heat can cause the plastic to become brittle and cracked. The silence plate should be replaced if damage is discovered during routine maintenance. A screwdriver is needed to replace the silence plate. Before working on the machine, make sure the engine is cool and remove the spark plug. Remove the air filter cover and the air filter to access the silencer plate. Remove the screws holding the plate in place. Install the new silencer plate. Tighten the screws. Install the air filter and housing cover. This silencer plate is made of durable molded plastic and is sold individually. It is a genuine OEM replacement part sourced directly from the manufacturer. This part is compatible with tillers, chippers, shredders, and small engines manufactured by Cub Cadet, MTD, and Yard Machines.

Plastic cover that snaps over the air filter assembly on lawn and garden engines. Replace if cracked, broken, or missing to protect the filter from dirt.

This part is a carburetor gasket. A carburetor mixes fuel and air before delivering it to the engine. The carburetor gasket creates a seal between the carburetor and cylinder that ensures that air is where it's supposed to be.The carburetor gasket may need to be replaced if the seal is broken and it is allowing air in. If there is a slight leak, the operator may notice engine roughness when it's at idle. A larger leak will cause the engine to vibrate, misfire, or hesitate under acceleration. Remember to wear gloves when operating or performing care and maintenance on any outdoor power equipment machines.This part is a genuine MTD part and is an OEM part sourced directly from the manufacturer. It it is sold individually. This carburetor gasket is compatible with engines, lawnmowers, log splitters, and trimmers manufactured by MTD, Yard Machines, Yard-Man, Cub Cadet, Husky, and Troy-Bilt.

Hex head bolt that secures components together on lawn tractors and outdoor power equipment. Replace if damaged, stripped, or missing to restore assembly.

A carbon canister air filter is an important piece that helps machines operate in accordance with environmental safety standards. This carbon canister air filter is an original OEM part sourced directly from the manufacturer, MTD. It is sold individually. It is designed for use with pieces of outdoor lawn and garden power equipment that have small engines, such as lawn mowers, tillers, string trimmers, edgers, log splitters, and wood chippers. It is compatible with products by brands such as Craftsman, Cub Cadet, MTD, Huskee, and Yard-Man.The carbon canister air filter part is a crucial device that is found in machines with small engines. The air filter is designed to decrease the amount of air pollution that the machine emits. It is serves the important purpose of increasing the machine's fuel efficiency. The carbon canister air filter traps the vapor the machine releases, but rather than letting it escape the fuel tank, it re-routes it back into the engine.The replacement or repair process of the carbon canister air filter should be straightforward, but the user replacing the part should always be sure to wear gloves during any assembly, replacement, or installation processes. The user should also refer to the owner's manual of their equipment and any guiding diagrams that clarify the placement location.

Replace your worn, broken, or missing throttle linkage spring. This small spring connects to the carburetor linkage on mowers, tillers, and engines.

Shield spacer for lawn tractors and riding mowers. Provides proper spacing and alignment for protective shields. Replace if missing, damaged, or worn.

Secures the engine shroud in place. Replace if worn, broken, or missing to keep the shroud properly attached and ensure adequate airflow around the engine.

This part is a replacement push cap. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. If the current push cap is broken or has been misplaced, this part can be used as a replacement. It is intended for use with several lawnmower models.The push cap is attached to the wheel hub cap and fits over the end of the axle shaft. This helps to protect the end of the shaft and the attached bolt that holds the wheel into position. When working on or near an engine, always ensure that the equipment is powered off and completely cooled down before attempting to undergo any repairs. For more accurate information on how and where to install this push cap, the appropriate owner's manual and equipment diagrams should be referred to. This push cap is suitable for use on a variety of lawnmower models manufactured by MTD, Yard Machines, Craftsman, Yard Man, and Troy-Bilt. It is a genuine OEM part and thus is made of high-quality, durable materials. This part is sold individually.

The breather hose is designed as a valve or vent that only functions one way. It allows air into the fuel tank but ensures that no air or emissions escape the tank. When this hose is not functioning, emissions and air could be leaking from the tank and cause the engine to perform poorly or not perform at all. The hose could become cracked or damaged, or the ends could lose their seal. Either way, a replacement hose will solve the problem and get the equipment back in order. This genuine OEM replacement breather hose is made by MTD and manufactured to exact specifications. It is compatible with several engines on lawn mowers, snowblowers, and chippers from brands like Troy-Bilt, MTD, Yard-Man, Yard Machines, Bolens, Cub Cadet, and Husky. There are more than 150 compatible machines for this breather hose. This high-quality composite rubber hose is sold individually.

Secures the log splitter's tray to the frame. Replace if your bracket is punctured, dented, warped, eroded, or has detached from the unit.

This back plate (sometimes just called a plate) is a genuine MTD part. It is manufactured as a replacement part for log splitters and some models of lawn mowers.On a log splitter, the back plate is a safety feature and also helps deliver pressure. It is not uncommon for the back plate to become damaged or broken through normal use of the log splitter. If this happens, it is important to replace promptly as the machine may no longer function or be safe to use. This back plate is a genuine OEM part sourced directly from the manufacturer. It is sold individually. A wrench is required to make this repair. It is designed for compatibility with machines made by Craftsman, White Outdoor, Remington, MTD Gold, Yard Machines, Columbia, Troy-Bilt, and Cub Cadet.

Engine valve cover cap for outdoor power equipment. Replaces cracked, broken, or missing valve covers on small engines. Direct fit for blowers, tillers, and more.