Roper Washer Parts

Removed LP Orifice and LP Gas limiter. Orifice was easy, however the gas limiter was the tricky one because I had no instructions to what went where. I could not find anything online as to how to convert from LP to Natural Gas, but you could find several things as to how to convert from Natural to LP. I ended up finding the Dryer schematic on line for the Whirlpool Duet natural gas dryer and was able to figure out what sequence the Spring, regulator and limiter went in. The order I just... Read more

• No hot or cold water

I tested the Atc. mid level switch, with my multi tester and found it was not sending enough current to the cold water inlet valve, so it would not open and let cold water in. I replaced the switch, (it was a snap) literally it snapped in place. replace the front face and turned the water back on and plugged in the washer, and turned it on. It worked perfect and has been since. good and easy repair even for a novice like me.. Read more

Replaced flow meter and control valve Read more

Undid a handful of screws, put the new panel in place and screwed them back in. Read more

After the part arrives, I was double check to make sure I got the right part. Importantly, unplug the electrical power first before do anything, also turn off the water hose for safety. Then removed 4 screw out side panel and 2 screw in side to get lose. After all, replaced a new part and put all panel and screw back together. Finally, plug in electrical power then a water hose and test a new part just installed. So far so good, seem like everything was function OK. Again, thanks for your web... Read more

I had replaced the Agitator cams a couple of times already due to my brother-in-law overloading the machine which stripped the teeth off of the cams. I also noticed the agitator seemed to 'wobble' and made 'knocking' noises quite a bit. I reviewed the video on the Appliance Parts Pros web site, disassembled the agitator and cleaned everything up, which helped a little, but not enough. Figuring the agitator itself was worn out also, I looked up and ordered all the parts for the upper agitator on... Read more

Replaced parts Read more

First I looked at the many you tube vids, and there are many. appliance parts pros pretty much shows you how to deal with the parts. I changed the brake shoes and the clutch assembly which also comes with the driver cam. I also changed the metal brake operating cam. I think that brake lockup or improper brake release was the problem that broke the plastic cam driver. This was the broken plastic part making all the ticking noise. I first changed the coupling on the motor but that wasn't bad. in... Read more

Replaced top ring and removed inner drum to remove pieces that were broken. Read more

In the end, with a new coupler. But I relearned old lessons the hard way. The washer is in a rental unit and the tenant complained of no spin. My first intuition was that the coupler failed again because I bought a cheaper one elsewhere a couple of years ago and not the brand name available here at AppliancePartsPros. But we’ll come back to that. Lesson #1: Verify the symptoms firsthand. I dug in right away, popped out the motor and the coupler appeared okay. When I spun it by hand, it turned... Read more

• No hot or cold water

I order the part from appliance parts recieed it in one day and it was repaired the next day so simple watched video thanks to you all is well i highly recommend you to anyone barbara mcallister Read more

My wife noticed that our washing machine was making a terrible rumbling noise and seemed to be out of balance all of the time. She was on the verge of calling a repairman when I said I wanted to look at it first. I noticed the agitator was very loose and would spin in your hand. I removed 1 bolt and the agitator was out. The teeth in the agitator were stripped out so by simply ordering a new agitator and installing it I turned a $250.00 repair call into a $70.00 DIY fix. Thanks. Read more

Purchased parts from your site and did a self repair. Excellent quality , speedy delivery and easy to install. Now our 13 year old washer works as good as new. Read more

I was actually getting an error code for the shifter and speed sensor. I ordered a shifter, which included the speed sensor, and replaced that part but the washer still didn't work. After doing some more research online, someone mentioned that the capacitor may be bad. After talking to my dad, who is an electrician, he said it sounded like my problem could very well be the capacitor. Knowing that we'd been without a washer for almost two weeks at this point, I went ahead and ordered the... Read more

Ordered the parts from AppliancePartsPros - super fast shipping, and even though I opted for regular shipping all of my parts arrived the very next day, including the big and bulky inner basket. Disassembly went smoothly, simply following the directions in the AppliancePartsPros video. The only problem I had was that the inner basket simply would NOT come of the drive block no matter what I did. Struggled for a few hours trying to take it off. Then, I called AppliancePartsPros and they said it... Read more

• Will not stop filling with water
• Will not fill with water

Replaced the water-level switch and hose. Washer works again, no overflowing since! Read more