Yard Machine Spring Tromm Throttle Cable Parts

• Will not drain
• Noisy

It was fairly obvious that the washer drainer motor had failed, water was not draining, filter was clean (bottom lower left panel door, have a pail ready!) and drain line was not blocked. Someone had provided great advice on the Appliance Parts Pro's site about replacing the drain motor from the bottom. Great suggestion! Easy to do, although be prepared for more water to drain from the washing machine onto the floor after you lay it over. I carefully lowered the machine onto it's back,... Read more

• No heat or not enough heat
• Won't start

Checked and cleaned vent which was in need of cleaning, but not too bad (I do not consider this a primary causal detail, but can be a problem, so clean yours). Replaced Hi-Limit Thermostat (safety thermostat) after confirming the circuit was open with ohm meter. While I was in there, I completely cleaned the heater and ducting and internal workings of the dryer. Confirmed the heater coils were good via 20ohm, 20ohm, 40ohm readings (LG service manual has wrong readings). Two weeks later, same... Read more

I consulted with the internet and your website and determined I had a bad roller wheel. I was going to buy just one but determined if you have to take the thing apart, just replace all of them. These lasted 10 years after all. Opened up You Tube for the method to take the dryer apart. After doing the washer last year, I felt pretty bold and just ripped into the project. Within 30 minutes I had the drum out and located the problem wheel ( rear right side). It was locked up due to hair build up... Read more

• Will not stop filling with water
• Leaking
• Shuts off too soon
• Will not fill with water

Replaced the cold water valve unit (has 4 ports and 1 inlet) which is very straight forward; requires : 1 phillips screwdriver ~#2 1 needlenose plier, medium size 1 channel lock plier, medium size 1 marker pen 1 - cold water valve assembly # AP4445613 1 - hot water valve assembly #AP4441935 1 - water level pressure switch #AP4440713 an old towel or two for absorbing small amounts of water a cellphone / camera for making sure you have the... Read more

• Leaks water

Repair went fairly smoothly by following the EXCELLENT how-to video provided. I had only a few issues and suggestions. 1. Because many of the screws and fasteners are of multiple sizes, I would recommend laying them out in a muffin tray or on a paper with labels for where they go back. 2. After removing the weights and prepping to remove the shock absorbers, after the front ones were removed, the tub tilted so far the rear shock absorber separated. The friction pads fell out. It was easy... Read more

Checked and cleaned vent which was in need of cleaning, but not too bad (I do not consider this a primary causal detail, but can be a problem, so clean yours). Replaced Hi-Limit Thermostat (safety thermostat) after confirming the circuit was open with ohm meter. While I was in there, I completely cleaned the heater and ducting and internal workings of the dryer. Confirmed the heater coils were good via 20ohm, 20ohm, 40ohm readings (LG service manual has wrong readings). Two weeks later, same... Read more

• Takes too long to dry

After I cleaned out the typical 1.5 pounds of lint from the vent, ( I do it every 2 months), I went searching for a solution. I found 6 possible causes on this site and purchased everything except a new burner; I wasn't going to go that far. Let the fun begin. Since my vacuum was still nearby, I thought I was ready for anything. Wrong. After I watched all the videos again for reassurance, I went in with screwdriver in hand and laptop nearby. I removed the top and looked inside. Don't be fooled,... Read more

Repair went fairly smoothly by following the EXCELLENT how-to video provided. I had only a few issues and suggestions. 1. Because many of the screws and fasteners are of multiple sizes, I would recommend laying them out in a muffin tray or on a paper with labels for where they go back. 2. After removing the weights and prepping to remove the shock absorbers, after the front ones were removed, the tub tilted so far the rear shock absorber separated. The friction pads fell out. It was easy... Read more

I watched the video that was shown on this website to slide the top back, remove the control panel, remove the front panel of the washer, remove the old gasket (the two tension springs are easy to get off, not as easy to replace), cleaned out years of gunk and soap that had built up behind the gasket for 10 years as well as under the rollers in the drum (each roller has a screw, remove it, slide the roller assembly forward and lift up to take off the rollers, and the roller can be broken down... Read more

• Won't start
• Lid or door won't close
• Door latch failure
• Will not agitate

Superfast parts delivery. Got packages by the second day. Videos were extremely helpful and well done; we couldn't have done without them although we came across slight differences in our machine and found workarounds. Our machine did not drain the water so I drained the water manually via drain tube at bottom of the machine and checked the filter for blockage. All clear so I read articles on the internet and watched videos and took a chance on replacing the drain pump and circulating motor... Read more

Repair went fairly smoothly by following the EXCELLENT how-to video provided. I had only a few issues and suggestions. 1. Because many of the screws and fasteners are of multiple sizes, I would recommend laying them out in a muffin tray or on a paper with labels for where they go back. 2. After removing the weights and prepping to remove the shock absorbers, after the front ones were removed, the tub tilted so far the rear shock absorber separated. The friction pads fell out. It was easy... Read more

We had a problem of lint building up inside of the filter slot. Once I took a long brush and cleaned the recess where the filter slides I was able to see that the old filter was not catching all the lint. Upon closer examination I noticed that the seal around the filter had become compressed. that's when I order another filter from AppliancePartsPros.com. My new filter came within three days and my dryer has been working fine ever since then. Read more

Was going to order 4 new wheel & spindle sets, then saw you could get just the wheel for 1/3 the cost, so I ordered those. Then in the frequently ordered other items I saw the idler wheel assy. So I ordered one of those also. Glad I did, it was in worse shape than any of the wheels which still seemed to spin freely after I got all the hairs and crap off them. Anyways, went by the video step by step. Pretty straightforward. Have a good vacuum handy, I’m surprised that it used to dry at all... Read more

Our 10-year-old LG WM2487HWMA front load washer had gradually developed multiple problems. It sounded like a jet engine during high speed spin, both the drain pump and circulation pumps were noisy, it would not drain properly (water was coming in during spin cycle), no water was spraying out at the top of the door into the drum like it is supposed to when the circulation pump was running. It's amazing we had still been able to wash clothes at all! With the help of the excellent... Read more

I watched the Appliance Parts Pro video and saw that it was a job that I could easily do. I ordered the Rotor Position sensor switch for about $21 on a Monday and it was delivered by UPS on Wednesday. The process was straight forward: 1) remove the back cover from the washing machine (4 screws), 2) remove the main bolt holding the magnetic drum on the motor; 3) remove the 6 bolts holding the coil on the motor; 4) remove the ground screw and wire harness clamp screw; 5) take the old sensor... Read more

Checked and cleaned vent which was in need of cleaning, but not too bad (I do not consider this a primary causal detail, but can be a problem, so clean yours). Replaced Hi-Limit Thermostat (safety thermostat) after confirming the circuit was open with ohm meter. While I was in there, I completely cleaned the heater and ducting and internal workings of the dryer. Confirmed the heater coils were good via 20ohm, 20ohm, 40ohm readings (LG service manual has wrong readings). Two weeks later, same... Read more