Kbl522kwms5 Parts

• Leaking

I have a Whirlpool Side-by-side Model ED22PWXBW01. A year ago, the ice cubes started freezing together in the rear of the ice bin for no apparent reason. Although the problem started off small, it gradually grew much worse, and finally I could see water dripping out of the ice mold and into the bin during the fill cycle. Re-levelling the refrig didn’t help, nor did adjusting the cube size / fill level. With guidance from the video, I removed the icemaker from the wall of the freezer. The... Read more

Water dispenser came down to a trickle and made a lot of noise, I changed the filter but it didnt help and thus the water tank/head assembly needed to be replaced. Replacing the water Tank/head assembly was an easy task, the hardest part is removing the covers and taking care of not breaking the insulation of the water inlet hose. For the not-so-experts like me it is also good to rememebr to have a bucket to collect all the water that comes out after the connection to the solenoid valves is... Read more

Thank you to everyone who entered comments, especially about the "Clicking" sounds when it was trying to turn on the compressor. I did not notice them at first, but then heard them and was confident that one of these parts (or both) had a problem. In my case, I have custom cabinets around the sides of the refrigerator and hardwood floors in the kitchen so I put down some cardboard when the rollers would need to go at an angle due to a center island in the way. (I would rather do this myself... Read more

Well with a lot of help from the world wide web and my friends from AppliancePartsPros.com, I was able to determine the source of the problem, which was the defrost thermostat. However, due to the disassembly involved to get to it, I decide to also change a couple of other parts involved in the defrost process, which are also located in the same compartment as the defrost thermostat. These parts were the thermistor and the defrost heater. Thanks to AppliancePartsPros.com, they had the parts I... Read more

One day my wife went to bake something and the bake/broil buttons as well as #3, #9, and oven light ceased to work. Local repair guy came by and wanted to charge $500 to fix it....YEAH RIGHT! Did a little homework and found this website, spoke with knowledgable staff who pointed me in the right direction. Took me all of about 20 minutes to install new control panel..everything works perfect...THANKS! p.s. In doing my research come to find Maytag did little to insulate control panel from oven... Read more

The video was very helpful, but my KitchenAid model required slightly more steps. Only the two screws in front held the filter housing, same as the video shows, but it has to be removed from the rear. My model did not have the wire brace, only the two front screws held the housing. Shut the water off and pull the electrical plug. Remove the two screws holding the filter housing in the front. Remove the lower panel in the rear at the bottom of the refrigerator. Remove the two screws holding the... Read more

Easy to remove the metal parts from the old bin. The only problem was that the screw that holds the adapter has red thread locker and screwdriver rounded off the head of the screw. Drilled the screw and heated the screw to loosen the thread locker and used an ease out to remove the screw. Read more

Replaced icemaker and shutoff arm. Easy project. Read more

The right door on our Jenn Air French Door Refrigerator would pop open & not fully close when the left door was closed first. Called the local distributor/dealer who advised me that the magnetic door gasket probably needed replacement (cost $300.00 + for the repair) What??? Visited you web site where I noted the right door had a "closure & bushing" on the bottom of the door. Could it be this was the problem fix? Took the right door off & examined both pieces. Sure enough the bushing was... Read more

• Ice maker dispenses too much ice
• Leaking
• Ice maker not making ice

Watched online video and worked along - it was easy and quick - I was amazed! Read more

Replace Read more

There is nothing you can't do given the right YouTube video! We disassembled the bottom mount freezer n our Jenn Air refrigerator to remove all the ice and then located the clogged grommet on the back of the unit and cleared it and added a notch. In the process of reassembling we broke the bracket on a part that should have been the easiest portion of the entire installation! In seconds we located and ordered the part on your site. It arrived in a couple of days and then we removed the door and... Read more

Replaced both primary and secondary water valves to make sure I fixed the problem. Both valves have to open when you function the water dispenser and when the ice maker tray needs refilling. YouTube video was a great help and let me know that I had to lengthen one hose. The video showed me the exact parts I needed to lengthen the hose. YouTube video also let me know that I had needed to transfer the internal springs in the hoses when I cut the old connections off. Never would have known... Read more

• Light not working

I saw your video on you tube and it seems very easy to do it my self, so I ordered the parts and I did it my self. It was very easy. Thank you for sharing with us on how to did it. One more thing, the parts arrived on the time they said it would come. Read more

• Leaking

Thought leak was coming from icemaker but refrigerator was making ice just fine. had puddle on floor just below freezer door. upon closer inspection realized leak was coming from drain line. there were 2 pieces of tubing and the connector. leak was coming from where tubing goes into connector. wanted to replace it. didn't know what it was called. did live chat with someone I think was named James. he sent me diagrams and I could identify the part. once identified I ordered it. boom.... Read more

We turned off the circuit breaker. We then removed the light cover and then the control panel. We disconnected the Keyboard, Utah, plugged in the new one and turned the breaker on to see if everything worked. We realized that we did not need a new jazz board so that is being returned. The old Keyboard was removed, the new one attached and all the parts were put back. The frig works fine now at the recommended settings of zero and 38F. Read more