Kfis525xvms9 Parts

Replaced relay and capacitor attached to compressor Read more

The little piece that holds crisper drawer on broke off. Every time pull drawer out lid fell off. I ordered left side panel. All I had to do was take drawer out unscrew old part take track off old part put on new part and screw back in. Took 5 minutes very cheap easy repair. Read more

• Ice maker not making ice

I used your online troubleshooting tips and watched the videos on your site. I determined my thermostat was defective, ordered the thermostat which arrived in two days and I replaced the thermostat and I now have a full bin of ice !!! The do it yourself video was extremely helpful and made the repair very easy. Thanks so much for the great service and quick delivery !!! Read more

I ordered new crisper drawer. Diagram made it easy to see the correct drawer needed. Received the drawer promptly. Read more

I first thought it was the auger in the ice container so I changed it and it was not the problem. I then talked to ApplianceParts customer service that it might be the yoke on the motor that turned the auger or even the motor itself even though it worked. I ordered the parts, the yoke was supposed to be able to be changed by itself but mind would not come off the motor shaft so I had to cut it off just to remove it from the unit so I had to change the motor anyway because of this. So I advise... Read more

I had a slow leak at the water inlet valve where the water line from the filter assembly connected to the water inlet valve. I determine that the water line had scratches in it which caused it to not seal. Had to buy the entire reservoir and filter assembly to get that water line. The replacement was smooth. It took about 30 minutes to swap out and it fixed the leak. Read more

Given all the symptoms, we figured that the control board went out. First, unplug the refrigerator. The control board was easy to access by removing a panel on the back of the fridge. I unplugged all the connectors and used a putty knife to release the board from the plastic retaining clips. There was some browning on the underside of the board and the back of the refrigerator that suggests one of the capacitors on the board blew. Install the new board by pressing it into the retaining clips... Read more

We turned off the circuit breaker. We then removed the light cover and then the control panel. We disconnected the Keyboard, Utah, plugged in the new one and turned the breaker on to see if everything worked. We realized that we did not need a new jazz board so that is being returned. The old Keyboard was removed, the new one attached and all the parts were put back. The frig works fine now at the recommended settings of zero and 38F. Read more

No instructions are included with either piece, which makes installation take more time and care. Tools needed: Small standard flat blade screwdriver, box knife or other knife with at least a 2" long blade, super glue. Remove the old main crisper frame: 1. Remove old main frame by lifting upward and outward. 2. Remove the center rail from the frame. May require bending of the main frame to remove it. 3. Remove the crisper front panel by unsnapping from frame. This is easily done by... Read more

I bought the listed condenser fan motor for my Maytag refrigerator. Access to the condenser fan is by removing sheet metal screws of bottom panel with 1/4 in. nut driver. Condenser fan is on left side of rear access area. Remove electrical connector by pressing-in connector release tab with thumb fingernail and pulling on connector. Remove three mounting screws with 5/16 nut driver. Work fan out to the right past the compressor. I used a pair of pliers, as a lever, behind the plastic fan blades... Read more

Pulled out storage bin Removed side track rail covers Popped off gear from holding clip Installed drive shaft Installed rail cover and storage bin Only took about 15 minutes Read more

Replaced relay and capacitor attached to compressor Read more

I ordered a new solenoid valve set and watched the online video of the replacement process. So after emptying my freezer and fridge, removing the doors and freezer drawer, so I could mover the fridge out of its cove, I discovered after taking the panels off the rear, that my fridge is different than that shown in the video. I went back online and discovered in one of the exploded views of the cabinet there is a panel inside the refrigerator which can be removed after taking the shelves out of... Read more

This was actually one of the easiest fixes I’ve done. All that was required was to remove 3 screws to remove the broken part. I used a pair of pliers to remove the moisture sensors from the broken part to the new one. Read more

Looked up parts based on fridge model number, watched videos, and replaced parts using just a few tools... easy. Parts came quick, well packaged. After 16 years, plastic parts deteriorate and break. The fridge was operating fine, but the drawers and covers were failing. Much cheaper to replace a few parts ($$-$$$) than buy a new fridge ($$$$). The new parts matched up exactly to old ones. The videos were very helpful, but not perfect... for the Crisper Frame, there was a structural metal... Read more

Ordered the piece and put it in the refrigerator. Read more