Lgr330adz Parts

• No heat or not enough heat

Being a complete DIY I hate to call some unknown person into my home knowing that just to get them there will cost me more than I will spend for parts that I don't need.After all, they are trying to make a living and by selling me parts that I don't need will increase their profits. I've dealt with APP before and was impressed by their site because I could find both mechanical and electrical drawings for almost everything I have. I looked up my dryer, decided what was probably the problem,... Read more

• Gas igniter glows, but will not light
• Won't start
• Element will not heat

After many years of excellent service the burner I use most often on the top of my JenAir range rusted through. After trying to remove the burner, which was firmly rusted into place, I decided to replace the cooktop pan, both burners and igniters. It was an easy repair to swap out the new parts for the old, and the only tool necessary was a #2 phillips screw driver. The only difficulty was that although the cooktop pan appears symmetrical, the screw hole pattern on each side is different. I did... Read more

The dryer is a Kenmore Laundry Center, model 417-99570150. Bought in 1998, so it is an older model. Not wanting to buy the newer ones that are out now. We opted to fix the Kenmore. Just believe the older models are worth fixing, if at all possible. Frist we had to figure out what parts we would need and if the cost would be worth our time. I went on YouTube: and type in Kenmore dryer not turning on. Watched several videos to narrow down the possible problem. Next step was to... Read more

This was actually one of the easiest fixes I’ve done. All that was required was to remove 3 screws to remove the broken part. I used a pair of pliers to remove the moisture sensors from the broken part to the new one. Read more

DIY. The delivery to Milwaukee took two days. The project was very easy and took about 1hr. The only tools required were a screw driver (electric) and a pliers. Just make sure your irganized with the screws so you don't lose any or mix up which ones go back in which holes. There's about 20 total screws. This $50 part saved me from having to buy my wife a $1000+ oven. Read more

• Marks left on clothes
• Noisy

I'm new to how a dryer works, so I just started taking it apart to see what exactly was causing it. The video examples on the APP website were all amazing. It gave me a good idea of what I was getting into and showed me the common repair issues. The dryer being 12 years old, I was on the fence about repairing or replacing. However, once I got a list of parts I might need and getting the confidence by watching the videos, I said "what have I got to lose." The cause of the scraping and loud... Read more

• Takes too long to dry

Get some acetone at a Hardware Store before you start. A pint will do. Unplug the dryer from 110 VAC. Pull the top off of the dryer, by lifting it from the front first. It is attached with snap metal fittings. Do not completely remove the top, just tip upright to gain access to the front interior of the dryer. Before you pull any wires from the door switch, record which color wires go to which terminals on the door switch. If you reassemble the connections incorrectly, the gas value will... Read more

Appliances will be sold with the house so the old oven racks were no longer shiny. Replacement racks present a better looking oven. Read more

Replaced the rear drum bearing assembly and the front top felt that the drum rides on and since I has it apart installed a new belt. Simple to do and takes very little time! Read more

• Door won't close

My dryer door would not stay shut because the door strike was stuck in the door catch. I was afraid that when I pulled the strike out, it would damage the catch, so I ordered the door strike and door catch. I got the damaged door strike out with needle nosed pliers in about 15 seconds. The door catch was in perfect condition so I didn't need to use the one I ordered. So then I proceeded to install the new door strike. That took me about 15 minutes because I did not have the manual strength to... Read more

• Gas smell
• Won't start

I replaced the burner head. I turned off power to the stove, although I did not turn off the gas. I gave the old burner head a slight twist counter-clockwise until it lifted off the stove. I used the pliers to pull the wires from the old burner, then placed them onto the contacts on the new burner. Set it in place, and gave it a clockwise twist until it was snug. This stove originally came with gaskets beneath the burners, but the info for the replacement part stated that a gasket was not... Read more

By reading the forums I first thought it may be the thermostat. I bypassed the thermostat wiring and the dryer still turned off after a few second of running. The second check was for the door switch. I couldn't find an explanation of how to bypass, so I just ordered a new one to try. It worked. Read more

I manually rotated the drum and could hear a noise in the lower right hand corner of the dryer. I turned off the breaker, removed the front covers to expose the blower fan. Blower fan was no longer attached to shaft and hitting the housing. Ordered a new blower assembly, rear bearing kit and lint filter on Friday at 09:00 AM and they arrived the next day at 13:00 (with standard shipping !!). 15 mins to troubleshoot. 30 minutes to replace parts and re-assemble. Running like new again !! ... Read more

I watched the helpful diy video. It gave me what the problem was and the confidence to do it. Took my dryer apart with the helpful hints in the video repair went smooth. Works like a dream and I saved money. Thank you appliance parts pros. Read more

• Timer will not advance

I ordered the timer and knob on Monday, they arrived around noon on Tuesday, and within an hour I had them installed and back in business. I was amazed how quickly the parts got here. The online video showing the procedure step by step was very helpful. Instead of disconnecting all the wires and having to keep up with which one went where, I moved each wire one by one and made sure I didn't get any of them in the wrong place. The only thing that slowed me down a bit was seeing which side of the... Read more

Start by removing the frame on the sides and bottom of the door. (Do not unscrew the corner screw holding the side frame and bottom together.) Be careful the glass will fall once the last screw is removed from the bottom so hold tight. Carefully remove glass and set aside. Remove top frame that held the handle. Once all the frame work and outer glass is removed unscrew the bracket that held the door handle from the door. Taking the top frame and bracket insert screw and washer and screw the... Read more