Maytag Neptune Parts

This genuine replacement part is a drive motor for dryers. The drive motor is the main engine that allows the dryer drum to rotate. If the drum is no longer spinning properly, the drive motor might need to be replaced. Luckily this is a relatively simple process.To replace the drive motor, begin by unplugging the dryer. Once it is powered off, uninstall the front panel of the dryer by removing the screws that attach it. After that, lift the top panel above the drum so that it is vertical and no longer covering the drum. Then disconnect the wires from the moisture sensors with a screwdriver by pressing down on the locking tab. Once the wires have been removed, lift the drum out from the dryer to gain access to the drive motor. Using a socket wrench, remove the blower wheel from the motor assembly. Then remove the old drive motor by unthreading the mounting screws that attach it. Install the new drive motor and reassemble the dryer. This OEM replacement part is sold individually and is compatible with Whirlpools, Maytag, Kitchenaid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Sears/Kenmore brand dryers.

Size: 5 foot long. Rubber fill hose used on most automatic washing machines. Two hoses used per machine.

This internal-bias thermostat regulates dryer drum temperature by cycling the heat on and off, helping maintain consistent drying performance and protect against overheating.

• Controls the cycling temperature of the heating circuit to prevent underheating or overheating
• Helps resolve symptoms like no heat, not enough heat, long dry times, or temperature swings
• A faulty thermostat may cause overheating that can trip the thermal fuse
• Located on the blower housing on many models

• Disconnect power and shut off gas (for gas dryers) before servicing
• Access the blower housing; note wire positions and transfer one at a time
• Mount the thermostat flush to the housing for proper sensing
• After installation, run a test cycle to verify proper heating

The LP Gas Conversion Kit is an OEM part for Whirlpool appliances. This kit allows for the conversion of natural gas appliances to use liquid propane (LP) gas. It includes all necessary components, such as orifices and instructions, to ensure a safe and efficient conversion.

Over time or due to specific needs, you might need to convert your appliance from natural gas to LP gas. Causes for needing this conversion include moving to an area where only LP gas is available or preferring LP gas due to its efficiency and environmental benefits.

Symptoms indicating the need for a gas conversion kit include:

• Moving to a location that only supplies LP gas
• Changing energy preferences for better efficiency
• Appliances set up for natural gas needing adaptation to LP gas

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This gas valve includes the coils. For the coils alone use part number 279834

This door seal fits around the dryer door opening to keep heat and moisture inside the drum. Replacing a worn seal restores airflow, improves drying performance, and helps prevent lint and warm air from escaping around the door.

• Seals the door perimeter to maintain proper airflow and temperature inside the drum
• Reduces heat and moisture loss that can lead to longer dry times
• Helps contain lint and dust around the door opening
• Replace if the seal is torn, brittle, flattened, missing sections, or if you feel warm air or see lint escaping around the door

• Disconnect power and allow the dryer to cool before servicing
• Remove the old seal and clean the door surface so the new seal seats flat
• Align and press the new seal evenly around the opening; avoid stretching
• Close the door to confirm latch engagement and an even seal; run a short test cycle to check for leaks

This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.

• Fastens panels, brackets, covers, or internal parts to the chassis or frame
• Helps maintain alignment and support, reducing rattle, vibration, or looseness
• Replaces missing or damaged screws that have backed out, broken, or stripped
• Restores secure mounting after service when original hardware is lost

• Disconnect power; shut off water or gas supplies before servicing
• Use the correct driver; start threads by hand to avoid cross-threading
• Match length and thread to the original location; do not substitute with longer hardware
• Tighten snugly; do not overtighten into plastic or thin metal

This door lock spin enable switch signals the washer's control that the door is securely locked so the cycle can advance into high-speed spin. Replacing a failed switch restores safe spin operation and prevents door/lock-related interruptions.

• Confirms the door latch is fully engaged and enables spin
• Prevents the drum from spinning when the door is not locked
• Common failure symptoms: won't spin or stops before high-speed spin; door/lock light doesn't come on; intermittent spin or door/lock error

• Disconnect power (and turn off water) before servicing
• Access the door latch assembly; remove the door boot clamp if required
• Transfer wires to the new switch one at a time; secure the switch in the latch housing
• Reassemble, verify the door locks, and run a spin test

This jumper wire connects two terminals in an appliance circuit to maintain proper electrical continuity. Replacing a burnt or damaged jumper restores reliable connections so switches, heating elements, and controls receive power as designed.

• Links designated terminals to complete the circuit per the unit's wiring diagram
• Restores continuity when the original jumper or connector is heat-damaged, corroded, or broken
• Visual indicators can include discoloration, melted insulation, or loose spade terminals at the old jumper

• Disconnect power at the breaker/fuse; turn off gas supply if applicable
• Reference the unit's wiring diagram; label/photograph existing connections
• Move one lead at a time; fully seat terminals and match orientation
• Do not use to bypass safety devices; replace any overheated mating connectors

The Leveling Leg Pad is an OEM replacement part for Whirlpool washing machines. This small but essential component fits beneath the leveling legs, providing stability and preventing the appliance from moving or vibrating excessively during operation. It also protects flooring surfaces from potential scratches or damage.

Symptoms of a bad Leveling Leg Pad include:

• Increased vibration or noise during the wash or spin cycle
• The washing machine wobbling or becoming unsteady
• Visible wear, cracks, or damage to the pad

Causes of a failing Leveling Leg Pad can include wear and tear from prolonged use, exposure to moisture, or excessive weight causing deformation. Replacing worn pads helps maintain the appliance's balance and efficiency.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

For the leveling leg order 22003428.

This blower wheel is threaded. For blower wheel for a "D" shaped shaft, order part# {AP4043265}.

The rubber foot is an OEM replacement part for Whirlpool washing machines. This small but essential component fits beneath the leveling legs, providing stability and preventing the appliance from moving or vibrating excessively during operation. It also protects flooring surfaces from potential scratches or damage.

Symptoms of a bad Leveling Leg Pad include:

• Increased vibration or noise during the wash or spin cycle
• The washing machine wobbling or becoming unsteady
• Visible wear, cracks, or damage to the pad

Causes of a failing Leveling Leg Pad can include wear and tear from prolonged use, exposure to moisture, or excessive weight causing deformation. Replacing worn pads helps maintain the appliance's balance and efficiency.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

For the leveling leg order W10176519.

This burner assembly is the gas/air mixing and flame head for gas dryers. Replacing a warped or corroded burner restores reliable ignition and steady heat so loads dry evenly and cycle times return to normal.

• Mixes incoming gas with air and directs it to the igniter for proper light-off
• Produces a stable flame to heat the dryer's airflow
• Replaces burners that are bent, rusted, or clogged and affecting ignition
• Typical symptoms: no heat, burner won't light, intermittent heat, or long dry times

• Disconnect power, shut off gas, and allow the dryer to cool before servicing.
• Access the burner compartment; note component positions and wiring for reassembly.
• Protect the igniter and sensor mounted near the burner from impact.
• After reassembly, restore gas and check all connections with a leak-detection solution; verify proper ignition and flame.

This hinge cover is a small trim piece that conceals the door hinge and mounting screws. Replace a cracked or missing cover to restore a clean, finished look and help keep lint and debris out of the hinge cavity.

• Covers and protects the door hinge and screw heads
• Restores a smooth, finished appearance around the hinge opening
• Helps shield the hinge pocket from lint and debris
• Common replacement when the original cover is cracked, missing, or loose

• Disconnect power; for gas units, also shut off the gas supply
• Support the door; loosen/remove hinge screws as needed to access the cover
• Remove the damaged cover; position the new cover and secure per model design
• Verify door closes and aligns properly before returning to service

This door boot drain hose channels residual water from the lower edge of the washer's door boot back into the tub/drain path. Replacing a cracked or clogged hose helps prevent front leaks, standing water, and musty odors around the gasket.

• Directs water away from the door boot/gasket into the tub or drain circuit
• Common symptoms: water pooling in the boot, leak at the front base, or musty odor near the door
• Replace if the hose is cracked, brittle, kinked, blocked, or leaking
• Restores proper draining from the door seal area

• Disconnect power and turn off water supply before servicing
• Access the hose at the door boot and its mating port; place towels to catch residual water
• Transfer or replace clamps as needed; fully seat hose on fittings and orient clamps correctly
• Run a short test cycle and check for leaks

This door lever actuates the latch/switch when the door closes. If it's worn or broken, the appliance may not sense a closed door and won't start. Replacing it restores proper door engagement and safe, reliable operation. What it does:

• Engages the door latch/switch mechanism so the control knows the door is closed
• Helps ensure the unit only runs with the door fully shut
• Replaces cracked, bent, or missing levers that prevent proper door sensing
• Common symptoms: won't start, must hold/push door to run, "door open" indicator stays on

• 1 door lever

• Disconnect power before servicing
• Access the latch/switch area; note the original lever's orientation and any spring
• Transfer and reuse existing hardware if needed; install the new lever in the same position
• Close the door and test for proper start/stop operation