Super Egg Small Engine Start Switch Parts

Took a bit to diagnose. First tried cleaning coils but the problem still persisted. Next took of the back panel and put the system into diag mode. (Press energy save button and fridge button for eight seconds system ding once a second and inverter board red LED will blink a code or be on solid if no issue. See back of the refrigerator for a sticker with what the number of blinks means. My unit one blinking 1 time. So I measured the resistance of the compressor between windings (8.9 ohms between... Read more

Replaced start switch. Read more

Checked the three door switches; used ohm meter to see if there was resistance or if a switch was bad. 2 out of 3 switches showed resistance with the ohm meter. The last one tested (of course the last one) NO (normally open) did not show resistance; I.e. the ohm meter reading did not change when the switch was depressed. Appliance parts pros was the only company that had the same model number I was looking for (SZW-V16-FD-63). I ordered the relay switch, 2 days later it arrived (regular... Read more

• Element will not heat

When I called customer service your representative at Appliance Parts Pros was able to help me diagnose the problem and order the two parts that I needed. both parts arrived the next day and with helpful tutorial videos I was able to replace both the Surface Unit Switch and the Universal Element in less than 45 minutes. Thanks so much for the great service and the money you saved me. Read more

• Light not working

Put in a new infinite switch behind the knob to control temp level. Read more

GE refrigerator 12 years old and we love it. Ordered compressor overload and compressor start relay video's were great made the replacement easy. I also ordered the control board because I felt this was the real culprit again the video was the best. With all the parts replaced GE profile refrigerator has been working like new. Thank you AppliancePartsPro.com Read more

• shuts off after a few seconds

I did some searching on the internet to see if others had the same issue I was having. There were many who had the same problem and everyone of them fixed it by changing out the latch switches, which in my case, were part of the latch body assembly. So I ordered the part from AppliancePartPros and it arrived on Tuesday, 2 business days after I ordered it, which was just as expected. I had also done some research regarding how to replace the latch body assembly and, although I couldn't find... Read more

Bought a new switch assembly, watched the video, and replaced the switch. Thr dryer now runs fine. Replacement part matched esxactly. Read more

Pop out the old switches with a putty knife pressing down on the tab, grabbed with pliers to pull out, disconnect the wires and connect new switches, pressing back in place. Read more

First, I modified old butter knife by bending a 90° angle about 3/4" from the tip. I slid the bent in up under the bottom of the switch cover and worked it to one side. I then rotated the knife downward using the bent end to pry the cover off. The switch is held by plastic arms on each side. The bottom right arm has a locating pin that fits into the switch. Unplugged the switch and re-installed. Read more

• Will not fill with water

Replacing the inlet valve solved the problem. The old valve was somehow clogged with white sediment. I probably could have taken it off and cleaned it out if I'd known, but replacing the valve was much easier. Took about half an hour to repair. Video walk through was extremely helpful. Great to have a working dishwasher again! Read more

Checked the three door switches; used ohm meter to see if there was resistance or if a switch was bad. 2 out of 3 switches showed resistance with the ohm meter. The last one tested (of course the last one) NO (normally open) did not show resistance; I.e. the ohm meter reading did not change when the switch was depressed. Appliance parts pros was the only company that had the same model number I was looking for (SZW-V16-FD-63). I ordered the relay switch, 2 days later it arrived (regular... Read more

• Element will not heat

We cut the power, took the control panel off, got the burner switch number from the original part, and ordered a new one. We were a little worried at that point, because your website offered a "replacement" part, with a different number than the original. However, we put the model number into your double check feature and were assured that we were getting the right part. The part arrived in two days and frankly we were still worried, because the new part was slightly larger than the original.... Read more

I used your chat and found out the year my stove was made. He also told me what part to order as one of the burners had stopped heating up. We watched the video on how to install it. My friend installed it and my stove burner now works. Read more

I took it apart to troubleshoot. I was pretty sure it was the switch but wanted to make sure it wasn't the element as well. Sure enough the switch was burnt at a little piece of copper protruding out the side. The plastic was blackened too which was a telling sign. The element was fine. I replaced the switch, turned on the cooktop and it worked again. Apparently, these switches are wired in series because when this one went out the rest of them wouldn't turn on either. Read more