Lnc8745a71 Parts

• Heat stays on after drum has stopped
• Will not tumble
• Touchpad does not respond
• No heat or not enough heat

Unpluged dryer first. Then took the lint filter out and removed the two philips screws inside the lint filter lid. Then take a paint scraper just under the top of the dryer two inches from the left front corner and pushed in a little to release the snap connector and did the same on the right side. Then lifted top over. Then take a 5/16 socket or nut driver and remove the two screws on on the left inside panel, then the right side. Lean front out a little and remove the two wires one the back... Read more

• Too hot
• Shuts off too soon

I posted the following on the Facebook page ; SOoooo my 10 year old clothes dryer stopped and like almost everyone else I just figured it's shot, burned up, gotta get a new one. Well, due to a few bumps in the road I cannot afford another problem. My 2 vehicles are not running and with one being in the shop for 3 weeks and not being able to afford a rental car anymore this dryer was another headache. It sat for weeks and laundry started piling up. While looking online for sales somehow I... Read more

• No heat or not enough heat
• Takes too long to dry
• Noisy

Our Maytag gas clothes dryer was not drying like it should/used to and was making a lot of noise. After researching online I figured the vent was partially blocked and/or the blower wheel was bad. When I took it apart, the vent had very little lint in the lower elbow exiting the back of the dryer but the blower wheel was loose on the shaft and was missing the clamp. I cleaned out the vent and put a hose clamp on the blower wheel to tighten it to the shaft and tried it again. The noise was... Read more

• No heat or not enough heat

The root cause was the front glides. They were virtually gone, and the drum was on metal to metal. So I replaced them with a front glide kit. I also replaced the belt, rear rollers, and lint screen. I am happy to say all the parts fit perfectly, and I couldn't find a better price anywhere else. I will definitely keep you on file for the next time I need appliance parts! Thank you! Sincerely, pw Read more

• Door won't close
• Shuts off too soon
• Doesn't shut off
• Takes too long to dry

Ordered a new clip and installed it. Easy to do. Unplugged the dryer. Removed the front. It is only held on by two screws. Removed wires to the door switch. removed the female end (it had the broken male piece in it. Inserted the new female part in the front, clipped in the male part into the door and reconnected the door switch wires, screwed the front back on. Job done. Total time was less than 10 minutes. Works like new. Read more

One day my wife went to bake something and the bake/broil buttons as well as #3, #9, and oven light ceased to work. Local repair guy came by and wanted to charge $500 to fix it....YEAH RIGHT! Did a little homework and found this website, spoke with knowledgable staff who pointed me in the right direction. Took me all of about 20 minutes to install new control panel..everything works perfect...THANKS! p.s. In doing my research come to find Maytag did little to insulate control panel from oven... Read more

Overall the fix wasn't too hard. The challenge was putting the oven door back together and holding it together while trying to tighten the screws. Enlisted my wife's help to hold the door and at first the handle screws wouldn't tighten. My cordless screwdriver's battery was under-charged. Once I switched batteries I was able to tighten the screws. Seemed like I needed to push too hard (my wife freaked "not so hard you will strip them!") however pushing hard was what was needed. Both screws... Read more

After shopping for a new Whirlpool Thin Twin Stack, Found appliance parts pros online and decided to take it apart to see if repair was a possibility. APPro's online instructions were easy to follow, in a couple hours it was apart, and I placed the order. Reg ground took a week from NY, so the laundry piled up that week. The parts arrived on Monday morrning, by afternoon the machine was running like new! The cause was the belt tensioner pulley had frozen. Replaced it, drum wheels,snap... Read more

The root cause was the front glides. They were virtually gone, and the drum was on metal to metal. So I replaced them with a front glide kit. I also replaced the belt, rear rollers, and lint screen. I am happy to say all the parts fit perfectly, and I couldn't find a better price anywhere else. I will definitely keep you on file for the next time I need appliance parts! Thank you! Sincerely, pw Read more

• Noisy

Replaced the motor, blower, rear drum felt seal, and drive belt. Vacuumed up the lint everywhere, cleaned extra lint out of the chute, around the blower, and rear vents. Read more

I took the dryer apart.....first had to clean out all the lint here and there. Took the drum out, inspected the belt and back support wheels. They seemed to be fine. In the front the drum turns on two supports that have a Teflon glide. Those two glides had been worn off with their pad so metal was rubbing against metal. Went online to appliancepartspros.com and looked up on the schematic what parts I needed. I also had called around locally and the same parts cost twice as much....so I... Read more

Found the right part at AppliancePartsPros.com, ordered the part, watched the tutorial. Took less than 5 minutes to install new door seal, and now our laundry area is no longer hot and humid. Before we changed the seal, warm air was leaking around the door and made the laundry room and the kitchen next to it unpleasant. Thanks for the great door seal and the handy tutorial! Read more

Decided to order the kit with both rollers even thou the right one looked OK.Also ordered the pulley for the idler. Watched the video for the pulley installation,super helpful on a couple of the steps!! Everything went great. A 14 year old dryer still has life! Parts ordering and delivery was also great!!! Thank you. Read more

Un plugged dryer. It was an easy fix, popped the top up. Removed the two screw that held the front on and also unclipped the door switch. Released tension that was on belt and removed drum. Removed old front slides cleaned up area and replaced them. Popped the ring that held the rear drum wheels and placed the new ones with a dab of grease. Un hooked tension spring for idler and removed old one and put the new one in. Make sure you place it through the correct hole and it makes it firmly into... Read more

After being told by a service repairman that it would cost me close to $200 to repair, I resolved to just not use the dispenser. After about a year, I had decided that I wanted to repair it and would look at the options myself. At the least, I could figure out which parts were needed to repair it and have them on hand for a service guy if I determined I could not do the job myself. The more I studied it, the more I felt confident that I could do it, and sure enough, when the part arrived - a... Read more

Took a screw driver lifted the top, Unscrewed two screws holding the front on the inside of the dryer one to left and one to the right. Laid the front on the floor and removed to other screws holding the collector in place, popped out old one cleaned all the lint and dust and popped the new one in put the new seal in place and done ! Read more