Parts for Whirlpool 3CFE2510W2: 03 - Section Parts

Replacement screw for washers. Used to secure various components including handles, panels, and internal parts. Order if original is missing or stripped.

Fix a dryer that won't start or trips breakers due to burned wires or loose connections. This terminal block kit includes wires and connectors. DIY repair.

Screw secures appliance panels and access covers. Replace missing, stripped, or corroded screws to restore tight fit and eliminate rattles or gaps.

Supports and pivots the hinged dryer top panel for service access. Replace if cracked, broken, or causing wobble, scraping, or alignment gaps.

U-type clip nut slides onto sheet metal panels to create threaded anchor points for screws. Replace if broken, missing, or worn during repairs.

Replaces worn dryer front bearing and seal that cause squealing or scraping noise. Essential for smooth drum rotation. Confirm fit with your model.

Adjustable leveling foot that screws into the bottom of your dryer cabinet. Replace missing, broken, or cracked feet to stabilize and level your unit.

Mounting screw for dryer assembly and panel attachment. Replace if screw is stripped, missing, or damaged during disassembly. Secures components.

Washer won't start or stops mid-cycle when door opens? The door switch detects door position for safe operation. DIY repair in 10-20 minutes with video.

Dryer won't start when door closes? A broken door switch lever prevents the dryer from detecting a closed door. Easy 10-minute DIY fix with video.

If your dryer door won't latch or the dryer won't start when you close the door, this top lock secures the cabinet during cycles. Easy 30-minute fix.

Includes two bumpers and two locking clips for securing dryer panels. Replace if clips are broken or missing to prevent rattling. Confirm fit with your model.

Dryer door won't close or stay latched? This door latch kit restores secure closure. Easy 15-minute DIY repair with common tools. Video guide included.

Dryer won't tumble or no airflow? This split-phase motor drives the drum and blower fan. Includes pulley and motor switch. Moderate difficulty repair.

Fix excessive dryer noise or vibration with a new motor base. This support bracket secures the motor assembly for stable alignment and quiet operation.

Get your dryer spinning smoothly again - install the Whirlpool 341241 OEM Drum Belt in minutes.

Why this belt?

• Exact factory spec: 92 ¼-inch length × ¼-inch width, 4 ribs / 3 grooves - built to Whirlpool standards, not a generic copy.
• Broad compatibility: Fits most Whirlpool-made dryers - Kenmore 110-series, Roper, Estate, Maytag, KitchenAid, Admiral, Crosley, Amana & more.
• Quiet, durable rubber: Reinforced EPDM resists cracking and stretch for years of reliable tumbling.

Fixes these common dryer problems

DIY install — about 15 minutes

1. Unplug dryer; remove lint screen housing & front panel.
2. Release belt tension at idler pulley; lift drum slightly to slide old belt off.
3. Loop new belt around drum, idler pulley and motor pulley (ribbed side down).
4. Re-assemble, run test cycle - enjoy quiet, consistent tumbling.

Replacement machine bolt for securing panels, brackets, and components in dishwashers, dryers, washers, and laundry centers. Restores fit if missing.

Replacement screw for washers. Used to secure various components including handles, panels, and internal parts. Order if original is missing or stripped.

Dryer won't power on or has loose power cord connection? This terminal block screw kit secures electrical connections. Easy DIY fix in 15 minutes.

Idler pulley maintains belt tension in your dryer drum assembly. Replace if the wheel is cracked, bracket is broken, or pulley has worn bearings.

If your dryer motor has come loose or makes grinding noises, this motor clamp secures the drive motor. Simple DIY repair with basic tools in under an hour.

Dryer won't tumble or no airflow? This split-phase motor drives the drum and blower fan. Includes pulley and motor switch. Moderate difficulty repair.

Dryer won't start or stops mid-cycle? A worn drive motor is often the cause. This motor turns the drum and circulates air. Moderate DIY repair.

Black screw that secures the refrigerator side trim or finish panel. Replace if screw is missing, stripped, or damaged to restore a snug fit and clean look.

Heat-resistant fiberglass gasket seals your oven door perimeter to maintain consistent temperatures. Replace when worn, frayed, or flattened to restore efficiency. Verify fit by model number.

Dryer door won't close or stay latched? This door latch kit restores secure closure. Easy 15-minute DIY repair with common tools. Video guide included.

Secures and guides the dryer door, acting as the pivot point. Replace if pin is worn, bent, or broken to restore proper door alignment and smooth operation.

Replace cracked, broken, or missing dryer door glass. Restores proper door visibility and appearance. Essential when outer glass panel is damaged or worn.

Replace your cracked or dented dryer door front panel to restore appearance and proper sealing. Matches original shape and finish. Verify fit with model number.

White outer door handle for dryers and washers. Snaps into place on the door panel. Replace if cracked, broken, or missing for easy door operation.

Replacement screw for washers. Used to secure various components including handles, panels, and internal parts. Order if original is missing or stripped.

Replace your dryer's worn, cracked, or broken drive belt. This cogged raw edge belt connects the motor to the drum. Essential structural component.

Secures the front panel to the dryer cabinet. Replace if cracked, broken, or damaged during disassembly. Installs at the panel-to-cabinet seam.

Fix a dryer that won't heat or has burning smell at the power connection. This terminal wire kit replaces burned wires and connectors. Easy DIY repair.

Fix dryer electrical connection issues with this terminal. Common when dryer won't start or power cuts out. Simple plug-in repair for most models.

Fix dryer electrical connection issues with this terminal. Used for wiring connections in heating and control circuits. Simple installation in minutes.

Replace a stripped, corroded, or missing mounting nut on your washer. Secures internal components and panels. Essential hardware for reassembly.