Need Help?
Call or text
Refrigerator door gasket seals the perimeter to keep cold air in and warm air out. Replace if worn, brittle, or loose. Confirm fit with your model.
Replace your freezer door gasket if damaged or causing temperature issues, frost buildup, or visible wear. Ensures proper seal. Verify fit with model.
This upper trim strip finishes the top edge of the appliance's front opening, restoring a clean look and helping protect nearby components. Replace a cracked, missing, or loose strip to keep panels aligned and secure.
My micro filter was in pieces when I pulled it out. Read more
O-ring seal prevents leaks between dishwasher components. Replace when you notice water drips or moisture buildup. Confirm fit with your model number.
WE replaced the drain pump and it still wouldn't drain sometimes. Finally we realized that the drain hose wasn't the correct bosch hose and the rubber was starting to bend and kink where it went through the hole to under the sink.So we bought the drain hose and replaced. Read more
This is a genuine OEM replacement o-ring sourced directly from the manufacturer for use on range vent hood switches. The o-ring provides a tight seal for the switch and keeps smoke from escaping through the switch connection. If the o-ring becomes worn or damaged, the vent will not remove smoke during cooking and should be replaced. Heat and debris pulled through the vent may cause the o-ring to warp. O-rings are not designed to last forever and may need to be replaced during the life of the appliance to keep it functioning correctly.To start, disconnect the power to the vent hood and dismantle the vent in order to reach the switch. To start, disconnect the switch and locate the o-ring. Remove the old one and dispose of it. Place the new o-ring in the groove and press firmly to seal the part. Lubrication is not necessary for installing the new o-ring. Reassemble the switch and put the vent hood back in place. Connect the power and try the switch to make sure it works. This o-ring is made of heavy-duty black rubber is and sold individually. It is designed for use in range hoods manufactured by Thermidor.
Found replacing the switch to be doable, but it was quite a delicate operation. This was for a Thermador range with a broken downdraft switch. It required the removal of 5 small screws which could easily be fumbled and dropped down where it would be difficult, if not impossible to retrieve. Two of the screws were facing the back, so it was a blind operation to remove and replace the screws. Required an offset screwdriver, as space was tight. So, be EXTREMELY careful to not drop the screws and... Read more
Oven door gasket seals the cavity to retain heat during cooking. Replace when torn, compressed, or allowing hot air leaks. Confirm fit by model number.
Replaced the display board and put in a new gasket to prevent the heat from escaping the oven and eventually "cooking" the display board. New parts worked perfectly and were easy to install, just had to keep track of a few screws and cables, nothing to it otherwise. Shipping was insanely fast- I ordered on a Friday afternoon, chose their standard shipping, and my parts were delivered the next day- Saturday morning- by 9am. My oven was working again by 10am. Amazing service! Read more
This door seal creates a watertight barrier between the dishwasher door and tub to contain wash water and steam. Replace a worn gasket to stop drips from the door area and restore a reliable, quiet seal.
Bought a Thermador PRSE48" dual fuel range from Craigslist really cheap because it didn't work. Did a little research and decided to overhaul most of the top (gas) end. For what I paid for it it was worth it and I'd have a good stove with new components. Replaced the griddle thermostat, ignition micro switches, ignition re-igniter box, installed fixing kit with 2 new potentiometers, both solenoids, and gas regulator. Had to replace 2 gas lines, all 4 jets, and one brass nut that were... Read more
Circular sealing gasket creating watertight joints between dishwasher components. Replace when flattened or cracked to prevent leaks. Confirm fit by model.
Seals the NTC temperature sensor port in your dishwasher to prevent leaks and ensure accurate temperature readings. Replace if leaking or worn. Verify fit with your model number before ordering.
Seals the aqua sensor assembly to prevent water leaks and protect electronics. Replace if you notice leaks or sensor errors. Confirm fit with your model.
Magnetic door gasket seals your refrigerator to prevent air leaks and maintain temperature. Replace when worn, cracked, or loose. Verify fit with model.
This side-trim gasket seals the edge of the appliance door/trim to help maintain a clean fit and reduce rattling or light air leakage. It restores the door edge seal for a neater appearance and improved closing performance. What it does:
Magnetic door gasket creates airtight seal to maintain temperature and efficiency. Replace if torn, cracked, or not sealing properly. Verify fit with your model number before ordering.
Silicone seal with adhesive for range hood installation. Replace when damaged, worn, or losing adhesion to maintain proper ventilation seal. Verify fit.
This 65-inch door gasket seals your range door to maintain proper temperature and prevent heat loss. Replace when worn, torn, or no longer sealing tightly.
RDFS30 requires door disassembly. See oven instructions for door removal. Removed door and set handle side down on towel lined tabletop, handle down and over edge. Removed 2 top inner screws and bottom glass bracket screws. Removed bottom side panel securing screws. Removed and flipped inner door panel off of glass. No need to remove oven handle off of glass, leave glass on table overhanging edge. Cleaned front inner glass surface. Removed inner door panel assembly (with spring hinges) from... Read more
Usually ships within 4 - 14 days