Thermador Switch

An integrated door switch for dishwashers that senses when the door is closed and allows the machine to start. Replacing a worn or damaged switch restores normal operation and helps prevent cycles from running with an open door. What it does:

• Detects door-closed position and tells the control board the door is secure
• Enables the dishwasher to start cycles only when the door is properly latched
• Prevents operation or pauses cycles if the door is open or not fully closed
• Common symptom: dishwasher won't start or stops mid-cycle when the door is opened

• Disconnect power to the appliance before attempting any service.
• Access typically requires removing the inner door panel or toe-kick; handle the door carefully to avoid damage.
• Replace the switch and reconnect wiring exactly as removed; ensure connectors are fully seated.
• After installation, restore power and ensure the door registers closed and the unit starts normally.

This air interlock is the airflow switch that helps monitor and control dryer vent airflow, ensuring the appliance only runs when proper air movement is detected. It replaces a worn or failed interlock to restore normal vent sensing. What it does:

• Senses airflow through the vent and signals the control system to allow or stop operation
• Prevents dryer from starting or continuing a cycle when airflow is restricted
• Common symptom: dryer fails to start, stops mid-cycle, or shows poor drying performance
• Can help address intermittent operation caused by a faulty vent sensing switch

• Disconnect power before servicing to avoid electrical shock
• Handle the switch and wiring gently; verify connector orientation before reinstalling
• Confirm venting is clear and intact when replacing this part

This switch assembly replaces a faulty E34 - 19HV switch to restore proper electrical control in the appliance. It provides the same fit and function as the original to help re-enable the affected control circuit safely. What it does:

• Acts as the electrical switch that completes or breaks a circuit when engaged
• Restores normal operation when a failed switch causes intermittent or no response
• Commonly associated with control failures, unresponsive buttons, or power-related symptoms
• Matches OEM form and mounting to fit into the original switch location

• Always disconnect power to the appliance before servicing
• Handle wiring and connectors carefully; note wire locations or take a photo before removal

This infinite switch controls the heat level of a range surface element, restoring variable burner temperature control for cooking. It replaces a failed or intermittent control to help burners cycle correctly across heat settings. What it does:

• Regulates power to a surface burner so the element heats and cycles across low-to-high settings
• Commonly replaces units that won't heat, won't change heat levels, or that stay on/off unexpectedly
• Works with manual knob controls to provide smooth temperature adjustment
• Matches OEM function for safe, reliable element control when installed correctly

• One infinite (ESC) control switch

• Disconnect power to the appliance before testing or replacing the switch
• Remove control knobs and trim as needed; handle glass or ceramic cooktops with care
• Verify correct wiring and mounting orientation against the service manual or wiring diagram

This push-button switch controls electrical power or function circuits in compatible Bosch appliances, restoring user input and on/off control when the original switch fails. What it does:

• Opens or closes the appliance's electrical circuit when pressed to enable a given function
• Commonly used where a user-operated control needs a durable, tactile interface
• Resolves symptoms like an unresponsive control panel, intermittent operation, or functions that won't toggle on
• Replaces a worn or non-clicking switch to restore reliable button response

• One replacement push-button switch

• Disconnect power to the appliance before servicing to prevent shock
• Verify correct terminal connections and orientation before final assembly
• Use basic hand tools; avoid forcing connectors to prevent damage

A reed switch door sensor that detects when the appliance door is closed so the control can start cycles. Replaces a failed magnetic sensor to restore reliable door-closed detection and normal operation. What it does

• Acts as a magnetic contact that signals the control when the door or lid is closed
• Helps prevent the appliance from starting if the door is open or not fully latched
• Common symptom fix for no-start, intermittent cycle start, or control not recognizing a closed door
• Works as the electrical switching element in the door/detector assembly

• One reed switch (single replacement sensor)

• Disconnect power to the appliance before replacing the part to avoid shock or damage
• Handle the switch and wiring gently; avoid bending or stressing terminals and solder joints
• Locate and access the door/detector area per your service manual or tech sheet; confirm connector orientation before installing

This is a replacement LIS CMT switch used to restore proper electrical switching for the control module and motor circuits. It helps return normal operation when the original switch is worn or failed. What it does:

• Acts as an electrical switch for the control module and motor circuitry
• Enables the appliance to complete control signals needed for motor or control functions
• Commonly linked to symptoms like no motor response, intermittent operation, or unresponsive controls
• Provides a direct replacement that fits the original mounting and connector arrangement

• Disconnect power to the appliance before attempting any repairs to avoid shock
• Handle the switch and connectors carefully to avoid damage to terminals or wiring
• Verify connector orientation and secure mounting when installing the new switch