White Westinghouse Parts

This replacement part is a black element mounting clip used in ranges or wall ovens. This clip is used for surface elements on electric ranges and ovens. The clip itself connects the surface of the element to the support bracket which allows the stove to heat up. The user might need a new clip or clips if the heating element on the stove is loose, if the heating element is completely detached, or if the clip itself is bent or broken. This clip is black and made of sturdy metal that can withstand heat as well as strain on the clip itself. Installation of this clip is very simple as it just requires replacing the old one with a new one and making sure it is secure. Pliers might be required if the old clip is bent or stuck near or on the heating element. There are no special tools needed for this repair. This is an OEM part sourced directly from the manufacturer. It is sold individually. This part is compatible with machines from Frigidaire and other brands like Electrolux, Gibson, Kelvinator, Crosley, Westinghouse, and more.

This thermistor is the dishwasher's temperature sensor. It reports water temperature to the control so the heater and cycle timing are managed correctly, helping restore reliable wash performance and more consistent drying.

• Monitors water temperature in the tub/sump and sends readings to the control board
• Helps the control regulate heater operation and determine cycle progress/timing
• Failure can result in no heat or poor drying
• May cause unusually long/short cycles or temperature-related fault codes

• Disconnect power at the breaker and shut off the water supply before servicing
• Access is typically from the toe-kick/base area or sump; remove the lower access panel as needed
• Release the locking tab/clip, remove the sensor, and ensure the existing seal/O-ring is properly seated; install the new sensor fully to prevent leaks
• Reconnect the wire harness, restore power, and run a test cycle to check for leaks and proper heating

The Thermistor is an OEM Replacement Part that maintains the temperature inside your Frigidaire refrigerator. This thermistor handles reading the internal temperature. After reading, it transmits this information to the control system. At a temperature of 29 degrees, the thermistor should exhibit a resistance of about 35k ohms. While at room temperature, it should read approximately 5k ohms.

Causes of a bad thermistor can include regular wear and tear, exposure to moisture, or electrical issues. Over time, the thermistor may become less accurate or stop working altogether.

Symptoms of a bad thermistor include:

• Inconsistent or incorrect temperature readings
• The refrigerator being too warm or too cold
• The cooling system running continuously or not at all
• Error codes related to temperature control

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Spacer that fits between refrigerator door hinge components to maintain proper clearance and alignment. Replace if worn, cracked, or missing.

Machine screw secures panels, brackets, and internal components in washers. Replace missing, rusted, or stripped screws to restore proper fit and alignment.

Freezer won't maintain temperature or cycles incorrectly? This thermistor sensor monitors temperature and signals the control board. DIY-friendly repair.

Replaces a cracked, broken, or missing control knob on your range. Attaches to the control shaft for heat and function settings. Restores appearance.

This is a black surface burner cap that sits on top of the burner base on a gas range cooktop. It distributes the gas flame evenly around the burner for consistent heating. Replace this cap if it is chipped, cracked, warped, or if you notice uneven flame patterns or difficulty igniting the burner.

The Supply Tube is an OEM part for Frigidaire gas ranges. It is a flexible metal tube that safely transports natural gas fuel from the household supply line to each burner assembly on the cooktop. 

Symptoms of a bad supply tube include: 

• Gas leaks at connections or along tube seams
• Inconsistent or weak burner flame levels
• Burners that light unevenly or not at all

Causes of failure can be cracking/corrosion of older tubing from regular heating/cooling cycles, damage from stove movement, or accidental kinks that reduce gas flow. 

Replace with this genuine Frigidaire supply tube to ensure a reliable source of fuel for each burner. It is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore gas ranges, providing years of dependable cooking performance. 

Replace your refrigerator's burned-out interior light bulb to restore clear visibility when opening doors or accessing the dispenser. Confirm fit with your model.

The Cord is an OEM replacement part for Frigidaire washing machines. Extending from the rear of the unit, it safely powers the washer through a connection to a wall outlet.

Causes of cord failure are normal wear from frequent coiling and plugging/unplugging motions over the appliance's lifespan. Rodents or sharp edges may also damage the outer jacketing.

Signs of a bad cord include:

• Exposed or severed copper wiring visible inside
• External cracks, splits or abrasions eroding the casing  
• Erratic behavior during the wash cycle
• GFCI/EGCI outlet tripping frequently

Compatible models also include Electrolux, KitchenAid, Jenn-Air, and Kenmore options. Maintaining safety is a top priority.

Routes water from supply to dispenser and ice maker. Replace this inlet line if cracked, kinked, or leaking to restore proper water flow in your fridge.

Refrigerator not cooling properly? A damaged or clogged condenser coil prevents heat rejection, causing warm temps. This assembly restores efficient cooling.

Replacement outer trim cover for refrigerators. Restores exterior appearance and protects internal components. Installs where original is cracked or missing.

Mounting screw for securing range panels, brackets, and igniters. Replace if stripped, missing, or damaged to restore proper fastening and alignment.

Replacement mounting screw secures trim, brackets, and panels inside your refrigerator. Restores proper fit when original screws are missing or stripped.