Whirlpool Dishwasher Heating Element

The Dishwasher Heating Element is an OEM replacement part for Whirlpool dishwashers. It is a vital heating component that raises water temperatures sufficiently for sanitizing dishes during hot rinse cycles. Proper heat is essential to drying fully.

Causes of a bad heating element can include scaling or mineral deposition over time that insulates it from conducting heat. Physical damage like burnouts or breaks in coils/wires are also possible.

Symptoms of a faulty element are:

• Dishes failing to get fully dry at the end of cycles
• Low wash water temperatures
• Buzzing, clicking or strange noises from under the dishwasher

This OEM Whirlpool part is also compatible with KitchenAid, Jenn-Air, and other Whirlpool-manufactured dishwashers. 

The Heating Element is an OEM part for Whirlpool dishwashers. This element is for heating the water to the required temperature and for the drying cycle, allowing your dishes come out clean and dry. It's positioned at the bottom of the dishwasher tub, where it heats the water and aids in the drying process by evaporating moisture from the dishes.

Causes of a bad heating element include mineral buildup from hard water, which can insulate the element and reduce its efficiency, or electrical issues such as a burnt-out coil.

Symptoms of a bad heating element:

• Dishes not being cleaned properly due to the water not reaching the optimal temperature.
• The dishwasher not drying dishes effectively
• The dishwasher taking longer to complete cycles

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Dishwasher Heating Element is an OEM replacement part for Whirlpool dishwashers. It safely generates heat to sanitize dishes and raise water temperatures during hot drying cycles. A functioning heating element ensures thorough cleaning and reduces the risk of damage from moisture left behind.

Causes of a bad heating element usually relate to standard wear and deterioration of wiring insulation or coil materials after extended usage cycles. Surface scale can obstruct heat transfer if not periodically removed.

Symptoms of a bad heating element include:

• Dishes not getting fully dry
• Moisture remaining in low areas after cycles
• Inability to select high-temperature settings
• Cycles that don't reach the required sanitization temps

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dishwashers.

This base heater assembly restores the oven's lower heating function in select convection microwaves. It delivers bottom radiant heat for baking and crisping so the unit can preheat properly and brown foods evenly.

• Supplies bottom heat during convection, bake, or crisp cycles
• Works with the control and temperature sensor to reach and maintain set temperature
• Common symptoms of a failed heater may include no heat in convection mode, very long preheat, or poor browning/crisping
• Visible damage to the element or tripping a circuit breaker may also indicate a shorted heater

• Disconnect power before servicing. Microwaves contain high-voltage components that can retain a charge even when unplugged
• Allow the unit to cool completely; access typically requires removing the outer cover or lowering an over-the-range unit
• Note wire locations and routing before removal; transfer any brackets, shields, or screws from the original assembly
• Route wires exactly as original and avoid pinching; confirm clearances before reassembly and test a convection preheat

This heater warms the wash water inside the tub during selected cycles. Replacing a failed element restores proper water temperatures, supporting cleaning performance and preventing extended run times or incomplete cycles. What it does:

• Heats water in the washer tub during hot/sanitize/temperature-controlled cycles
• Helps maintain target temperature for effective cleaning and stain removal
• Common symptoms include water not heating, cycles taking unusually long, or cycles stopping early
• Accompany control errors related to water temperature or the heater circuit

• 1 heater

• Disconnect power and shut off water supplies before servicing
• Access is typically from the rear or bottom; be prepared for residual water when removing the old element
• Clean sealing surfaces and seat the element fully; tighten fasteners evenly to prevent leaks
• After installation, run a hot cycle to check for leaks and heating

This heater is the electric heating element assembly that generates heat for drying cycles, restoring proper drying performance and cycle temperatures when the original element fails. What it does:

• Converts electrical power into heat to warm the air used during drying cycles
• Commonly linked to no-heat or low-heat symptoms and prolonged drying times
• Can cause the dryer to overwork or run longer when the element is damaged
• May trip thermal fuses or breakers if shorted or grounded

• One heater assembly

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Access typically requires removing the dryer cabinet or rear access panel; follow OEM instructions
• Inspect and replace related safety parts (thermal fuses, high-limit thermostats) if they show failure
• Test the new element for continuity and secure all electrical connections before reassembly