Whirlpool Dishwasher Switch

The Speed Control Plate is an OEM part for Whirlpool stand mixers. This part regulates the speed at which the mixer operates, ensuring that it can accurately adjust to the desired setting for a wide range of mixing tasks.

Over time, the speed control plate can wear out or become damaged due to regular use, leading to issues such as the mixer not maintaining the set speed, operating too fast or too slow, or not adjusting speeds at all.

Symptoms of a bad Speed Control Plate include:

• The mixer fails to change speeds or adjust accurately
• The appliance operates at an incorrect speed regardless of the setting
• The mixer only works at one speed or does not work at all
• Unpredictable speed changes during operation

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Water Level Switch is an OEM part for Whirlpool dishwashers. It monitors and regulates the water level inside the dishwasher during wash cycles, ensuring the correct amount of water is used for optimal cleaning performance.

The water level switch can fail due to several reasons, such as electrical issues, mechanical wear over time, or damage from water exposure. Blockages or debris can also interfere with its proper functioning.

Symptoms of a bad water level switch include:

• The dishwasher not filling with water
• Overfilling or flooding inside the dishwasher
• The dishwasher stopping mid-cycle or not progressing through cycles
• Error codes related to water levels

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Door Switch is an OEM part for Whirlpool dishwashers. It plays a crucial role in ensuring the dishwasher operates only when the door is securely closed. The switch signals the control board that the door is shut, allowing the wash cycle to begin safely.

You should replace the door switch if it becomes faulty or damaged. Causes of a bad door switch can include wear and tear from regular use, electrical issues, or physical damage from forceful closing of the door.

Symptoms of a bad door switch include:

• The dishwasher not starting or stopping mid-cycle
• Error codes related to the door latch or door switch
• The dishwasher operating with the door open (safety issue)
• No response when pressing the start button

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Float Switch Kit is an OEM part for Whirlpool dishwashers. It includes the float and the switch mechanism that monitors and controls the water level inside the dishwasher. The float switch ensures that the dishwasher does not overfill by signaling the water inlet valve to shut off the water supply once the appropriate level is reached.

Causes of a bad float switch can include debris or mineral buildup, wear and tear over time, or electrical failures within the switch mechanism. A malfunctioning float switch can lead to water overfilling, which may cause leaks and inefficient washing performance.

Symptoms of a bad float switch kit include:

• Dishwasher overfilling with water
• Water leaks during operation
• Dishwasher not filling with enough water
• Error codes related to water levels

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Restore smooth, consistent motor operation with this 120V electronic speed control board. It regulates power to the motor so selected speeds engage properly and stay steady, helping your appliance run reliably across all settings. What it does:

• Regulates power to the motor for accurate speed selection
• Helps maintain steady RPM under load
• Common symptoms: runs only one speed, won't change speeds, surges or pulses
• Resolves intermittent operation when the motor has power but won't run

• 1 speed control board assembly

• Disconnect power before servicing; work in a dry area
• Handle the board by the edges to avoid static damage
• Move wires from the old board to the new one one-by-one; take reference photos
• Some models require speed calibration after installation—follow the service instructions

Overfill control.

This miniature door switch is the snap-action interlock that tells the appliance when the door is closed. Replacing a worn or sticking switch restores reliable start/stop and proper door-status sensing for safe, consistent operation. What it does:

• Acts as the latch/interlock sensor for door open/closed status
• Signals the control to allow or prevent operation based on door position
• Typical symptoms include: won't start or shows a door message, stops when the door is bumped, or light/fan behavior doesn't match door position

• 1 miniature door switch

• Disconnect power before servicing. If working on a microwave, high voltage may be present even when unplugged—properly discharge the capacitor.
• Access the latch/interlock area; note wire positions and transfer one lead at a time to the new switch.
• Use a multimeter to confirm the switch changes continuity when pressed before reassembly.

Color: Black. Instruction sheet included.

Oven light switch.

The Float Switch is an OEM part for Whirlpool dishwashers. It is a safety component that detects water levels and monitors flood conditions. The float switch ensures the dishwasher only runs water when needed and shuts off water flow if it detects a potential leak or overflow situation. 

Symptoms of a bad float switch include: 

• The dishwasher fails to fill with water or stop the water when the cycle is complete
• Loud buzzing or humming noises coming from the float switch area  
• Water leaks inside or outside of the dishwasher due to overfilling
• Repeated error codes related to flooding or water level detection

Causes of a bad float switch could be wear and tear over time, defective wiring or electronic components inside the switch, or damage from moisture or leaks. 

This OEM replacement is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This motor wax lubricant conditions dryer motor bearings and helps reduce noise from dry or worn spots. It's a simple maintenance item that restores smooth rotation and can help extend motor life when applied as directed. What it does:

• Lubricates motor bearings and low-friction surfaces to reduce squeaks and grinding noises
• Helps prevent metal-on-metal wear caused by dry spots during operation
• Restores smooth rotation for quieter, more efficient motor performance
• Safe for typical dryer motor materials when used per manufacturer guidance

• One motor wax lubricant packet

• Apply only to the exact bearing or shaft surfaces specified by the manufacturer; do not over-apply
• Disconnect power to the appliance before accessing the motor or applying lubricant
• Avoid getting wax on belts, pulleys, electrical components, or brake surfaces
• If motor noise persists after application, inspect motor and related parts for wear or damage