Whirlpool Dishwasher Guard, Shield, Barrier Parts

The Toe Panel Insulation is an OEM part for Whirlpool dishwashers. This part was designed to enhance the appliance's performance by reducing noise and preventing heat escape from the bottom of the dishwasher. This insulation panel fits snugly behind the dishwasher's toe panel, which is located at the lower front part of the unit. 

Causes of a bad Toe Panel Insulation might include wear and tear over time, damage during appliance installation or removal, or deterioration due to moisture exposure. 

Symptoms of inadequate or damaged Toe Panel Insulation include:

• Noticeable increase in noise level from the dishwasher, making it more disruptive during its operation.
• Excess heat felt near the base of the dishwasher, indicating heat loss.
• Potential for condensation or slight temperature changes in the kitchen due to the heat emitted from the dishwasher.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Hinge Brace is an OEM replacement part for Whirlpool dishwashers. It serves as a supportive bracket anchoring the dishwasher door hinge assembly firmly in place.Note: This part may be different from your original. If your original part was a flat plastic vapor barrier, the new design is a wire. It is a factory design change, the old design is no longer available.

Over time, the hinge brace can degrade due to constant use, heavy loads on the door, or accidental impacts. A faulty hinge brace can result in misalignment or difficulty in operating the dishwasher door.

Symptoms of a bad hinge brace include:

• Loose or unstable door that does not close securely
• Gaps appearing around the door seal during wash cycles
• Broken hinge components from added stress and tension on the door
• Difficulty fully opening or closing the dishwasher door

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air and some Kenmore models.

This Barrier protects and separates appliance components, keeping wiring and parts properly aligned for reliable operation. It's a simple, durable replacement that restores the original spacing and support inside the appliance. What it does:

• Provides a stable mounting/separation surface to prevent rubbing or contact between parts
• Helps maintain correct component alignment to reduce vibration and noise
• Prevents wiring or small parts from contacting hot or moving components
• Common symptom: visible cracks, breaks, or shifted parts where components no longer sit securely

• One barrier as shown

• Disconnect power to the appliance before servicing to avoid electrical shock
• Remove any panels or covers that block access; keep track of fasteners
• This part typically installs with screws or snap-fit tabs—do not force components

This replacement capacitor shield protects the appliance's capacitor from debris, contact and shorting, helping extend component life and reduce electrical faults. It installs over the capacitor to block dust, wiring contact and accidental damage. What it does:

• Covers and protects the capacitor from physical contact, dust and loose wiring
• Helps prevent short circuits and arcing caused by accidental contact with the capacitor
• Useful when existing shield is cracked, missing or deformed
• Can reduce risk of intermittent electrical faults related to exposed capacitor

• One capacitor shield (protective cover)

• Always disconnect power to the appliance before servicing
• Capacitors can hold a charge; discharge safely before touching electrical components
• Remove necessary access panels to reach the capacitor; replace shield without stressing wires

This replacement shield is a small protective cover that helps guard nearby components from heat, moisture, or debris, reducing wear and preventing damage for reliable appliance operation. What it does:

• Covers and protects adjacent parts from heat, moisture, grease, or debris
• Helps maintain proper airflow or clearance around components where fitted
• Prevents rubbing, chafing, and minor impact damage to wiring or panels
• Can reduce noise caused by loose or exposed parts contacting other surfaces

• One replacement shield

• Disconnect power (unplug or shut off breaker) before inspecting or replacing the shield
• Follow OEM disassembly steps for access; handle mounting tabs carefully to avoid breakage
• Use appropriate fasteners; replace any damaged clips or screws with OEM equivalents