Whirlpool Parts

Color: Stainless

This is the removable metal oven bottom for the lower oven cavity. It forms the floor above the heating components, protecting them from spills while providing a clean, even surface for baking and easier cleanup.

• Shields heating components beneath the lower-oven floor from drips and debris
• Provides a flat, durable surface inside the oven cavity
• Helps promote even heating and airflow within the oven
• Typical replacement reasons: warped or rusted panel, chipped/flaking enamel, persistent smoke/odors from burnt-on spills

• Disconnect power at the breaker and allow the oven to cool completely before service
• Remove oven racks for access
• Remove the mounting screws (often at the rear), then lift and slide the panel out
• Reinstall with existing hardware; ensure proper clearance from the heating element before restoring power

This is the factory replacement microwave door assembly. It restores a smooth, secure door closure and proper operation so the unit can open and close reliably and look like new. What it does:

• Provides a complete, aligned door to open/close the cavity smoothly
• Ensures latch hooks engage properly so the appliance can operate
• Replaces doors that are cracked, warped, or have broken handle mounts
• Addresses issues like the unit not starting unless the door is pressed, or stopping when the door is moved
• Helps resolve sparking/arcing around the door opening caused by a damaged door choke or screen

• One door assembly

• Disconnect power at the breaker before servicing; microwaves contain high-voltage components
• For over-the-range units, support or remove the microwave from the wall to safely access and handle the door
• Transfer any reusable hardware/hinge pins/trim from the original door as needed
• Align the hinges and verify the door closes, latches, and opens smoothly before remounting

This is the lower access panel for the appliance's base. It finishes the front opening and shields internal components, helping reduce noise and keep dust and debris away from the motor and wiring.

• Covers the lower service opening beneath the door to provide a clean, finished look
• Helps protect internal components from debris and accidental contact
• Can reduce vibration noise when properly secured
• Replace if the panel is bent, cracked, rusted, missing, or rattles/doesn't stay secured

• Disconnect power; also shut off the water supply
• Support the existing panel while removing mounting screws; retain hardware for reuse
• Position the new panel, align with mounting holes/slots, and reinstall screws—do not overtighten
• Confirm door clearance and that the panel sits flush without interference

This control panel mounts on the appliance's door and provides the push-button interface for selecting cycles and options. Replacing a cracked or unresponsive console restores reliable button operation and a clean, factory look. What it does:

• Houses the user-interface buttons and indicator windows used to select cycles/options
• Provides a rigid mounting surface for the door's UI components
• Helps protect internal wiring at the top of the door
• Typical symptoms: buttons don't respond or work intermittently, unit won't start when Start/Resume is pressed, selections change unpredictably, or the console is cracked/loose

• One console assembly

• Disconnect electrical power; turn off the water supply if needed
• Open the door and remove the inner-door perimeter screws to separate the console from the inner panel
• Note and transfer any reusable parts from the old console as required; make secure, straight ribbon/harness connections
• Reassemble the door, restore power, and run a quick function check before final tightening

The Dishwasher Front Door Panel is an OEM part for Whirlpool brand dishwashers. Forming the outer surface of the door, this stainless panel provides a protective barrier and the surface for mounting handle components. 

Causes of a bad front door panel can include damage from repetitive closure stresses, impacts from loaded dishes, or cracks developing from regular cleaning chemicals.

Symptoms of a bad front door panel include:

• Cosmetic damage detracting from appearance
• Obstructions preventing proper latching of the door  
• Leaks forming at the door gasket sealing surface

This OEM replacement is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore models. 

The Control Panel is an OEM part for Whirlpool ranges. As the interface between the user and appliance, the control panel is responsible for housing all of the electronic controls and display that allow for selection and monitoring of oven functions like temperature, bake time, locks, and timers.

Causes of a bad control panel can include cracked or worn buttons or displays that no longer register touch input properly. Splashing liquids or steam exposure over time can cause internal circuitry issues as well.

Symptoms of a bad control panel include:

• Unresponsive or malfunctioning buttons
• Fading or inaccurate displays
• Error codes indicating electrical faults
• Inability to properly turn elements or functions on/off

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This part is the outer panel for the drawer on a trash compactor. This part protects the wiring and other components inside of the drawer and also provides a decorative finish for the face of the unit.In the event that the stainless steel finish becomes scratched, dented, or damaged in any way, this is a high-quality replacement part. The screws may need to be reused when installing the new part, so keep those in a safe place so they do not get lost. Before replacing this part, unplug the unit from the electrical outlet or turn off the house circuit breaker. Wears gloves for safety during this process.This outer panel is compatible with trash compactors that are manufactured by the Whirlpool and KitchenAid brands. It is sold individually and sourced straight from the manufacturer as a genuine OEM part.

Color: White. Includes insulation. Other colors: For almond use WP3384157, for biscuit use WP3384157, for black use WP3379920.

This broiler pan is the heat-safe tray used for broiling in the oven or broiler drawer. Replace a rusted, warped, or missing pan to maintain safe broiling and simpler cleanup by catching drippings.

• Holds food for broiling and supports correct placement under the broiler
• Collects drippings to help reduce flare-ups and smoke
• Restores safe use when the original pan is rusted, pitted, dented, or warped
• Seats on the designated rails/supports in the broiler drawer or compartment per model design

• Allow the appliance to cool completely; wear cut-resistant gloves
• Remove the broiler drawer or open the broiler compartment as your model requires
• Position the pan on the proper rails/supports and verify stable seating before use
• Follow your model's user guide for broiling setup and care

This backsplash restores the rear trim behind a range or cooktop, protecting the wall and covering wiring openings for a clean, factory-look finish. It replaces a damaged, dented, or missing backsplash to improve safety and appearance. What it does:

• Covers the gap between the cooktop and the wall to block spills, splashes, and heat from reaching the wall surface
• Hides wiring and mounting holes for a neat, finished look
• Replaces bent, cracked, or corroded rear trim that can collect grease and grime
• Helps maintain proper clearance and original appearance of the appliance

• One single-piece backsplash

• Basic hardware and mounting locations are OEM-specific; confirm matching fasteners on arrival
• Turn off power to the appliance and move the unit away from the wall before removing or installing the backsplash
• Use care to avoid scratching the finish during installation; two people may be needed for larger ranges
• If mounting holes or brackets are damaged, replace those items before installing this backsplash

This replacement access panel restores the finished look at an appliance service opening and keeps internal components protected from dust and debris. Use it when the factory panel is cracked, dented, loose or missing. What it does:

• Covers the appliance access/service opening to protect wiring and components from dust and accidental contact.
• Restores the exterior appearance where the original panel is cracked, dented or broken.
• Helps reduce drafts and keeps small objects out of the service cavity.
• Provides a correct replacement part for repair or cosmetic restoration when the original panel is damaged or missing.

• Disconnect power to the appliance before removing or installing the panel.
• Removal/installation typically requires basic hand tools (screwdriver or nut driver) to release screws or clips—do not force fasteners.
• Align panel tabs/clips and secure with the original hardware.

This heat deflector directs and shields heat inside the appliance to help protect surrounding components and maintain proper airflow. It's a simple replacement for torn, warped, or missing deflectors. What it does

• Redirects heat away from sensitive components to reduce risk of heat damage
• Helps maintain consistent airflow paths for proper appliance performance
• Commonly replaced if warped, cracked, melted, or dislodged
• May reduce odors or burning smells caused by contact with hot parts

• Disconnect power (and gas, if applicable) before beginning any repair
• Inspect surrounding mounting points and replace any damaged fasteners if needed
• Handle carefully—sharp edges may be present

This control panel assembly replaces a worn or damaged front touch/control surface and restores proper user controls and display visibility on the range or oven. Designed to match original fit and appearance. What it does

• Houses the touch buttons, display window and associated front-facing controls used to set oven functions and temperatures.
• Replaces cracked, faded, or unresponsive control surfaces that can interfere with entering settings or reading the display.
• Restores a secure, finished face for the console and helps protect internal control electronics.
• Compatible with service-side mounting and connects to the internal control board via factory wiring harnesses.

• Handle carefully to avoid scratching the finished face; use soft gloves if available.
• Disconnect power at the breaker or unplug the appliance before beginning any service.
• Installation typically requires removal of the oven/range console trim and attachment screws; keep fasteners for reuse.

This top panel is the exterior upper cover that protects internal washer parts and gives the appliance a finished look. It restores a secure mounting surface for the control area and helps keep water and debris out of the cabinet. What it does

• Covers and protects internal components at the top of the washer cabinet.
• Provides the mounting surface and alignment for the control console and lid.
• Restores appearance when the original panel is dented, cracked, or rusted.
• Reduces rattles or vibration caused by a loose or warped top.

• Disconnect power and water supply before starting any repair.
• Use basic hand tools; some screws or clips may need to be removed to lift the old panel.
• Handle edges carefully — metal panels can be sharp.
• Have a second person assist if needed to prevent bending or dropping the panel.

This caster support wheel helps restore smooth movement and stable support for the appliance's cabinet or drawer assembly. It replaces a worn or damaged wheel so the part rolls and aligns correctly. What it does:

• Replaces a worn or broken caster wheel that prevents smooth rolling
• Restores proper support and alignment for drawers or appliance base panels
• Reduces catching, scraping, or noisy movement caused by damaged rollers
• Helps maintain consistent front-to-back leveling when used with leveling hardware

• One caster support wheel

• Designed for basic drop-in replacement; position part where existing caster was mounted
• Turn off power and remove food/items or shelves from the cabinet/drawer area before working
• Use appropriate hand tools; avoid over-tightening fasteners which can bind the wheel