Whirlpool Range Parts

After trying different ways to repair, I went looking for metal replacement knobs. Found them here at Appliance Part Pros. Ordered Thursday and FedEx delivered Saturday. I can't ask for better service. Read more

• Won't start

First, it was going to cost $95 for an appliance guy just to look at it! I figured there would be an upcharge on the parts + labor on top of the $95, so I took a chance & decided my husband & I could fix it cheaper; we were right, but it was a 3 week process (luckily, we have another microwave in the basement we were able to use in the meantime). I googled the microwave model #, then price checked the same item I thought we needed; printed off the diagrams of the various microwave "systems" &... Read more

• Element will not heat

Purchased a new Element surface and installed same... All Okay now... Read more

Like a boss! Seriously, removed oven from wall (2 screws), removed about 15 sheet metal screws from front and top covers, unplugged wire harnesses one (or a few) at a time. Reassembled. Hint. Take a picture of wiring before removing and mark old parts (especially thermal fuse) with sharpie before removing so you don't get confused. It's really hard to tell a used electrical part from a new one. Read more

Just removed the old glass top which consisted of removing 6 screws Read more

The problem was partly caused because the original legs were at full extension. The replacement legs were longer than the originals and were more secure at the needed length. One difficulty was that the threaded base plate where the legs screwed in had been damaged and had to be reshaped, I was able to reshape the sockets with some effort, to allow the legs to thread in, though one remained slightly angled. (A metal tool of some type which could be threaded in and used to bend the socket area... Read more

Replaced the control that I think was bad from the purchase of the stove new as the burner didn’t throttle as is does now. Read more

I purchased a burner and a oven orifice replacement kit from Appliance Parts Pros. I downloaded an installation manual from Whirlpool and followed the instructions. It was pretty easy. The front burner orifices could be replaced by just taking off the burner cover. The back ones required removing the burner diffuser. You will need to reattach the back burner bottom assembies after you remove the diffuser before you unscrew the orifice or it might bend the burner piping causing it to not line up... Read more

• Little to no heat when baking

Purchased bake and broil elements as well as temp sensor. Oven is 18 years old...wasn't sure which was not functioning properly. Carefully Removed all three components, and then installed new. Oven heats perfectly. Saved buying new wall oven. Installation was very easy. I am a homemaker and mom. We can do all kinds of fix its. These folks are outstanding! !!! Items arrived very fast and packaged well. Read more

• Little to no heat when broiling

I wanted to get the upper oven baking element replaced; it hasn't been working for a few months. This double oven has had two other issues, there is a fan that comes on to cool the electronics panel, That fan has made excessive noise and it operates for 2-3 hours after the oven turns off. The other problem with the oven is the Self-Cleaning feature runs for about 15-30 minutes and then turns off with an error code. I've had a local appliance repair person in to address the error code and... Read more

Replaced igniter under oven floor panel. Read more

Ordered the grates. It is perfect. Your company is the only one that has it. Read more

Ordered the new knob and replaced it. Read more

Removed control panel and replaced broken switch. Much easier then expected. Read more

Simply Replaced it with a new one I order on line . I just had to screw the new handle on. Read more

• Won't start

I have a Jenn-Air microwave that didn't turn on and had no lights. It just stopped working completely. I unplugged the unit and had to remove the rear cover using a *security screw kit* that prevents people from opening the rear panel. Once opened, I removed the fuse and testing it with an OHM reader to determine that the fuse went bad. But I also had to determine why the fuse blew and noticed a sticky oily substance under the Capacitor. I used a rubber glove and needle nose pliers to... Read more