Whirlpool Wall Oven Parts

This 8-inch coil surface element restores reliable heating on the large burner of electric ranges and cooktops. Its 2350-watt design provides steady, even heat for boiling, frying, and everyday cooking.

• Converts electrical power into heat for the large cooktop position
• Common failure symptoms: no heat, uneven heating, only part of the coil glowing, visible breaks or blisters, or failed continuity
• Plug-in coil style for receptacle-type burner sockets
• If no heat persists after replacement, also inspect the element receptacle and the burner switch

• Disconnect power to the range/cooktop and allow the element to cool completely
• Lift the old element and pull straight out from the receptacle
• Align the new element's terminals with the receptacle, push in firmly until fully seated, and set it into the support/drip bowl
• Restore power and test the burner

This terminal block provides an insulated, secure junction for incoming power or harness leads inside the appliance. Replacing a cracked, loose, or heat-damaged block restores a safe, reliable connection and helps prevent arcing or intermittent power.

• Creates a fixed, insulated junction between external supply wires and internal appliance wiring
• Maintains tight screw-lug connections to minimize resistance and heat buildup
• Helps ensure steady power delivery to controls, motors, and heaters
• Common indicators of failure: melted/discolored block, burning odor, visible arcing, loose or stripped terminals, intermittent or no power

• Disconnect power at the breaker and verify zero voltage before servicing
• Photograph/label wire positions; transfer one lead at a time to the new block
• Tighten terminal screws firmly; do not overtighten into the insulator
• Inspect wire ends/ring terminals and strain relief; replace any heat-damaged components per the service information

This fan motor powers the cooling fan that moves air through your unit. Replacing a worn or noisy motor restores proper airflow to help maintain stable temperatures and reliable performance. What it does:

• Drives the fan blade to circulate air for cooling and temperature control
• Helps prevent component overheating caused by weak or stalled airflow
• Fixes: fan not running or starting intermittently
• Fixes: loud humming, grinding, or rattling from the fan area
• Fixes: longer run times or warm spots due to poor airflow

• Includes: 1 fan motor

• Disconnect power before servicing; allow moving parts to stop
• Note wire positions and motor orientation; take a photo for reference
• Transfer the existing fan blade and mounting hardware as needed
• After install, ensure the fan spins freely and no wiring contacts moving parts before restoring power

This door latch keeps the door securely closed and engages the door switch/interlock so the appliance operates as designed. Replacing a worn or broken latch helps resolve door-related errors and restores reliable, safe operation.

• Secures the door against the strike for proper closure and alignment
• Actuates the door switch/interlock so controls recognize a closed door
• Helps prevent operation when the door is open or not fully latched
• Common symptoms: door won't latch or stay closed; unit won't start or shows a "door/open-close" message; broken or loose latch hook

• Disconnect power before servicing; use proper PPE and beware of sharp edges
• Access the latch through the door panel/trim as applicable; use non-marring tools to avoid damage
• Transfer any reusable clips/springs from the old latch to the new part
• After installation, verify smooth door closure and that the control detects the door as closed

The Convection Fan is an OEM part for Whirlpool wall ovens and ranges. It circulates hot air inside the oven cavity, facilitating even heat distribution during the cooking and baking cycles. The convection fan enhances cooking performance through fast, forced air movement.

Causes of a bad convection fan include a failed motor, worn-out blades, or blockages that disrupt airflow.  

Symptoms of a bad convection fan include:

• Incomplete or uneven cooking even at higher temperatures
• Longer than normal cook times 
• Loud buzzing or grinding noises from the fan motor area

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This grommet is located between the glasstop and the knobs. Color: White. Measures about 2 inches in diameter. For black order W10854242. For biscuit order 3191817.

This oven door gasket forms the heat-resistant seal between the door and oven cavity. Replacing a worn seal helps the oven reach and maintain temperature, reduces heat loss around the door, and supports even, consistent baking performance.

• Creates a continuous seal between the oven door and frame to contain heat and moisture
• Helps maintain accurate temperatures and normal preheat times
• Replaces torn, frayed, flattened, or brittle seals that allow heat to escape
• Common symptoms include hot air leaking near the door, uneven baking, and longer cook times

• Disconnect power at the breaker and allow the oven to cool completely before servicing
• Open the door and remove the old gasket, noting clip/pin locations and orientation
• Press the new gasket evenly into the retaining channel or holes; do not stretch the seal
• Close the door and verify uniform contact around the frame for a snug seal

This is a switch membrane, also known as a keypad, that is used with ovens, ranges, and stoves. The part is located in the center of the front of the appliance. It is made up of several layers and acts as a switch to turn the appliance on and off. It also includes several buttons so users can choose cooking settings, set temperatures, and otherwise alter the operation of the appliance.Regular use or damage can cause the switch membrane to become damaged. When this occurs, the buttons may not work correctly or there may be no way to turn the appliance on and off. If this is the case with a switch membrane, it should be replaced. Unplug the appliance and remove the screws from the back. Find the tabs on the side and press them to remove the housing. Remove the bottom screws to take off the ribbon connector. Remove the original part and replace it with the OEM replacement component.Created for compatibility with KitchenAid ranges, ovens, and stoves, the switch membrane is sold as a single part. This is an authentic OEM replacement component that is sourced straight from the manufacturer.

This inner oven door glass mounts on the inside of the door to help seal in heat while letting you view cooking progress. Replace damaged glass to restore safe viewing, proper insulation, and consistent oven performance.

• Forms the inner pane of the oven door window and acts as a thermal barrier
• Helps the oven reach and maintain set temperature by limiting heat loss through the door
• Provides visibility into the oven cavity during cooking
• Replace if the glass is cracked, shattered, missing, or heat is escaping from the door

• Disconnect power and allow the oven to cool completely; if applicable, shut off gas
• Remove the door and place it on a protected, flat surface before disassembly
• Wear cut-resistant gloves and eye protection; handle glass carefully and support the edges
• Reuse existing brackets, seals, and screws; note orientation during reassembly

Color: White. This knob measures about 2 inches in diameter. For black use WP98006100. For biscuit use WP98008208. Sold individually.

This pilot burner supplies the small, continuous flame that lights the surface burners on gas ranges/cooktops, helping ensure reliable burner ignition and steady performance.

• Provides a steady pilot flame to ignite the surface burners
• Helps restore lighting when surface burners won't ignite or the pilot won't stay lit
• Can address weak or inconsistent pilot flame at the top burners
• Typical signs include repeatedly having to relight the pilot or burners going out during use

• Disconnect electrical power and shut off gas before servicing
• Allow the appliance to cool and ventilate the work area
• Inspect and clean mating surfaces; replace brittle tubing or cracked fittings as needed
• After installation, check for leaks and adjust the pilot flame per the service manual

Color: Black

This control knob barrel is the inner sleeve that connects the knob to the control shaft. Replacing a worn or cracked barrel restores a snug fit so the knob turns the switch or valve reliably without slipping.

• Couples the knob to a D-shaped or splined control shaft
• Restores positive engagement for smooth, accurate adjustments
• Replaces a stripped, cracked, or missing inner sleeve
• Common symptoms: loose or wobbly knob, knob spins without changing settings, or falls off

• Disconnect power; for gas appliances, shut off gas supply
• Pull the knob straight off; remove the damaged barrel from the knob
• Align the new barrel with the shaft shape and press it fully into the knob
• Push the knob back onto the shaft until seated; verify proper operation

The Microwave Thermostat is an essential component for maintaining the optimal performance of your microwave. This genuine OEM part ensures precise temperature control, allowing your appliance to operate efficiently and safely. Designed specifically for a variety of Samsung microwave models, it guarantees a secure and seamless fit, making installation straightforward for DIY repairs. The thermostat regulates the heating process, preventing overheating and ensuring consistent cooking results every time you use your microwave. By replacing a faulty thermostat with this reliable part, you can restore your microwaveGÇÖs functionality and extend its lifespan without the need for professional service. Its durable construction ensures long-lasting performance, giving you peace of mind and contributing to the overall safety of your kitchen. Whether your microwave is experiencing temperature fluctuations or failing to heat properly, the Microwave Thermostat provides a practical and effective solution. Choose this genuine OEM part to achieve dependable results and enjoy a consistently efficient microwave experience.

This light socket holds the bulb and supplies power for reliable appliance lighting. Replace a cracked, heat-damaged, or loose socket to restore safe, consistent illumination inside the appliance.

• Secures the lamp and connects it to the appliance wiring
• Restores proper electrical contact to the bulb
• Replaces sockets showing arcing, discoloration, melting, or a loose fit
• Common symptoms: light won't turn on, flickers, works intermittently, or bulbs fail prematurely

• Disconnect power at the breaker or unplug the appliance before servicing
• Allow the appliance to cool completely before accessing the socket
• Use the bulb type and wattage specified for your model
• Transfer existing mounting screws/brackets and wiring connectors as needed; ensure tight, clean connections

Color: Stainless Steel

The Knob is an OEM part for Whirlpool ranges. It provides selection of cooking functions and specific temperature levels.  

Causes of a bad knob can include cracked or warped knobs due to high heat exposure over time, loose/worn internal mechanisms, or damage from impact or moisture.

Symptoms of a bad range knob include:

• Knob that feels loose, wobbly or dysfunctional when selecting functions
• Inability to reliably set desired cooking temperatures
• Knob detaching from shaft or assembly during use
• Unintended changes or engagement of cooking functions

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.