Whirlpool Wall Oven Parts

This replacement control knob restores smooth, reliable selection of your appliance's settings. Installing this part helps you accurately choose cycles, temperatures, or burner levels again.

• Attaches to the control shaft to operate a switch, valve, or timer
• Provides clear position indexing for accurate setting selection
• Typical symptoms: loose or wobbly knob, slips, won't turn the control, or falls off
• Replacing a damaged knob can resolve difficulty selecting cycles, temperatures, or burner output

• Disconnect power before servicing; if working on a gas range, also shut off the gas supply as needed
• Pull the old knob straight off the shaft—do not pry against the control panel
• Align the new knob with the shaft orientation and press straight on until fully seated
• Verify operation by rotating through all positions

This infinite switch controls power to a 6-inch surface element on an electric range or cooktop, allowing smooth heat adjustment from low to high. Replace a worn switch to restore consistent burner control and cooking performance.

• Regulates power to a 6-inch surface burner as you turn the knob
• Provides variable heat by cycling power on and off at the selected setting
• Typical failure symptoms: burner won't heat, only heats on high, won't adjust temperature, or won't shut off

• Disconnect power at the breaker before servicing
• Pull off the control knob and access the switch from the control panel; note/take a photo of wire locations
• Transfer wires to the new switch one at a time to match terminals; mount the switch and reinstall knob/panel
• Restore power and test the 6-inch burner through all settings

This LP bake orifice meters propane to the oven's bake burner to deliver the specified BTU output. It helps ensure a stable, blue flame and consistent baking performance after LP conversion or when replacing a damaged or missing spud.

• Meters LP gas to the bake burner for the intended BTU output
• Promotes correct flame size and color for efficient, even baking
• Useful after LP conversion or when the original orifice is clogged, damaged, or missing
• Symptoms can include weak or unstable bake flame, oven not reaching temperature, or yellow/sooty flame

• For LP use only; verify the correct orifice for your model and gas type
• Disconnect power and shut off gas; allow the oven to cool completely before service
• Access the bake burner orifice holder; start threads by hand to avoid cross-threading and tighten snugly—do not overtighten brass
• After reassembly, leak-check all gas connections and verify proper flame/air-shutter adjustment.

This replacement seal restores a tight barrier between mating components, helping prevent leaks and maintain proper performance. Install it when the original seal becomes worn or damaged to keep moisture and fluids contained where they belong. What it does

• Creates a watertight/airtight seal between connected parts
• Helps prevent drips, seepage, and moisture escaping from joints
• Maintains correct system pressure/flow at the sealed connection
• Replace if the old seal is cracked, flattened, swollen, or brittle
• Common symptoms include moisture around the joint, intermittent leaks, or residue/mineral trails

• 1 seal

• Disconnect power and, if applicable, shut off water supply before service
• Remove the old seal and clean the groove and mating surfaces thoroughly
• Lightly lubricate with manufacturer-approved silicone grease only; seat the seal evenly without twisting
• Reassemble, restore utilities, and run a short test to check for leaks

This surface heating element restores reliable heat to an electric range or cooktop's top burner. Replace a failed or damaged element to bring back even, responsive heating for everyday cooking. What it does:

• Supplies heat to the selected surface burner when the control is turned on
• Can correct no-heat, weak or intermittent heat, or overheating due to internal failure
• Replaces elements with visible damage such as breaks, burn marks, or hot spots
• Helps restore consistent temperature control across the cooking zone

• 1 surface heating element

• Disconnect power at the breaker and allow the cooktop to cool completely before servicing
• Access the element per your model; note wire locations and any brackets before removal
• Transfer wires and any retaining hardware to the new element in the same positions
• Avoid stressing the element or insulation; ensure it sits level and clear of glass/trim before reassembly

This gas range surface burner head distributes fuel through its ports to create an even cooking flame. Replacing a worn or clogged head restores quick ignition and consistent heat for everyday cooking.

• Channels gas from the orifice through burner ports to produce a stable, even flame under the cap
• Provides the proper surface for the spark electrode to ignite the burner
• Replace if the burner won't light or has delayed ignition
• Replace if flames are weak, uneven, yellow, or sputtering
• Also indicated by cracked/warped metal, corrosion, or ports that can't be cleared

• Disconnect power and shut off gas before servicing
• Remove grate and burner cap; lift off or unfasten the old head
• Clean the orifice area; align the new head over the orifice and electrode; seat fully
• Reinstall cap and grate; restore utilities and test ignition and flame pattern

This spark ignition module generates the high-voltage pulses that light the burners' igniters on a gas appliance. Replacing a failed module restores consistent ignition so burners light reliably when you turn the control to ignite. What it does

• Converts line voltage to high voltage to create the ignition spark at each burner igniter
• Distributes spark pulses to multiple burners during lighting
• Common failure symptoms include no spark on all or several burners, intermittent/weak sparking, or clicking without ignition
• Helps eliminate the need to light burners manually

• One spark ignition module

• Disconnect power and shut off gas supply before servicing
• Access the module, note wire positions, and transfer connectors one at a time to the new module
• Mount securely and ensure all terminals are fully seated; avoid pinching or chafing wires
• Reassemble, restore power and gas, and verify proper ignition on all burners

• If only a single burner won't spark, check that burner's igniter and spark switch/wiring first; the module typically affects multiple burners.

This replacement door glass restores a clear viewing window and the structural integrity of your appliance door if the original glass is cracked, shattered, or damaged. It helps keep operation safe while returning the door to a like-new appearance. What it does:

• Forms the transparent viewing window in the appliance door
• Helps maintain proper door integrity and safe operation
• Restores visibility into the cavity during use
• Replaces cracked, chipped, loose, or shattered glass

• 1 door glass panel

• Disconnect power and allow the appliance to cool completely before servicing
• Wear cut-resistant gloves and eye protection when handling glass
• Support the door; some models require removing the door to access the glass
• Transfer any brackets/trim from the old glass and avoid overtightening fasteners

The door hinge is an OEM part for Whirlpool ranges. This piece serves as the anchor for stable, smooth opening and closing of the oven door. 

Causes of a bad door hinge include warping from repeated heat exposures and compromising its secure gateway function over time. Breakdowns disrupt workflows. 

Symptoms involve: 

• A sagging oven portal is unable to support itself when ajar  
• Grating or binding movements straining the hinge mechanism
• Difficulty latching or sealing the door during baking

This OEM Whirlpool part is also compatible with some Maytag, Jenn-Air, and KitchenAid ranges.

The Infinite Switch is an OEM part for Whirlpool ranges. It is the control switch for the surface element that allows the user to adjust the heating element to different power levels for precise cooking control.

Causes of a bad Infinite Switch can include overheating, damage from spilled liquids or debris beneath the control panel, or failure due to years of repeated use and exposure to heat.

Symptoms of a bad Infinite Switch include:

• Inability to adjust heating element power levels
• Element remaining stuck on high heat
• Switch malfunctions such as intermittent power or failure to turn off completely
• Visible damage, corrosion, or loose connections around the control area

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This oven door glass assembly replaces a damaged or shattered viewing panel so the door seals and insulates properly while letting you monitor cooking. Restores clarity and helps maintain temperature when the original glass is compromised.

• Forms the viewing window and part of the oven door's thermal barrier
• Replace if the panel is cracked, shattered, missing, or heavily scratched
• Helps reduce heat loss through the door after glass damage
• Restores a clear view into the oven cavity

• Disconnect power at the breaker and allow the oven to cool completely
• Remove the door per your model's instructions and place it face-down on a padded surface
• Handle glass carefully and wear cut-resistant gloves and eye protection
• Transfer any reusable trim or brackets from the old panel; tighten fasteners evenly without overtightening

This is the surface burner igniter electrode for gas cooktops/ranges. It creates the spark that lights the surface burner, restoring reliable ignition and eliminating the need for manual lighting.

• Generates the spark to ignite the surface burner flame
• Helps address issues like no spark at a burner, intermittent ignition, or clicking without lighting
• Can resolve weak/damaged electrode tip causing poor spark
• Correct arcing to ground near the burner head

• Disconnect power and shut off gas before servicing
• Handle the ceramic insulator carefully to avoid cracking
• Ensure proper positioning and gap to the burner cap per service guidance
• Route and secure the lead away from heat and sharp edges; reconnect firmly to the spark module harness

Color: Black. Measures about 2 inches in diameter. For biscuit use WP98008208. For white use WP98006102. Sold individually.

Color: Black   power burner knob

This condenser fan blade mounts to the fan motor and pulls air across the condenser coil and compressor. Replacing a cracked or warped blade restores airflow so your refrigerator cools efficiently and the compressor runs at a safe temperature.

• Circulates air through the condenser coil and over the compressor to remove heat
• Helps maintain cooling performance and stable system pressures
• Common symptoms: weak or no airflow at the rear/base, rattling or scraping noises, wobble/vibration, visible cracks or missing fins, warmer-than-normal compartments or hot cabinet sides
• Works with the condenser fan motor and shroud; typically replaced when the hub is stripped or the blade is damaged

• Disconnect power and pull the refrigerator out; remove the rear access cover near the compressor
• Note blade orientation and depth on the motor shaft before removal
• Pull the old blade straight off; press the new blade onto the shaft until fully seated and ensure it spins freely with proper shroud clearance
• Reinstall the cover, restore power, and verify strong, quiet airflow

Color: Black