Parts for Maytag A300S: 12 - Rear View Parts

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This factory bolt is a direct-replacement fastener used to mount and secure appliance components. Replacing a stripped, rusted, or missing bolt restores a tight, rattle-free fit and helps keep assemblies aligned for reliable operation.

• Secures components to prevent loosening from vibration and normal use
• Helps maintain proper alignment of parts and assemblies
• Replaces hardware that is stripped, corroded, or lost
• Common symptoms include loose or wobbling parts, vibration, and rattling noises

• Disconnect power and shut off water/gas before servicing
• Compare length and thread to the original fastener; transfer any washers/spacers from the old bolt
• Start by hand to avoid cross-threading; tighten per service manual—do not overtighten
• Apply thread-locking compound or replace companion hardware

This part has been discontinued and is no longer available.

The Tub Bearing Kit is an OEM part for Whirlpool washers. It includes all the necessary components to replace the tub bearing which is responsible for supporting the inner tub and allowing it to spin smoothly during the wash cycle. Over time, the bearing may wear out or become damaged, leading to excessive noise, vibrations, or even leaks from the washer.

Causes of a bad tub bearing can include regular wear and tear, exposure to heavy loads or unbalanced loads that put excessive strain on the bearing, or damage due to water leaks.

Symptoms of a bad tub bearing include:

• Excessive noise or grinding during the wash cycle.
• Vibrations or shaking of the washer.
• Leaks from the washer, around the tub area.
• The inner tub not spinning or becoming stuck.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

Note: It is advised to replace the Mounting Stem Repair Kit, part number 6-2040130 at the same time.  To complete the repair, you’ll also need a Spanner Wrench to complete the repair (TB123B).

Clamp Includes 205529 Bolt Kit. It Does *not* include The The Rubber Seal. If Seal Required, Use WP211232

This hose clamp secures a hose connection to prevent leaks and keep your appliance running smoothly. It provides a tight, reliable hold on the hose fitting so water or air stays contained during operation.

• Tightens around a hose and fitting to maintain a secure seal
• Helps stop drips, seepage, or loose connections
• Common fix when you see moisture around a hose joint
• Useful if a clamp is rusted, stretched, or no longer holding tension

• Unplug power and shut off water (if applicable) before servicing
• Note clamp position/orientation before removal
• Use appropriate screwdriver or nut driver to tighten evenly
• Do not overtighten—ensure a snug, leak-free seal without damaging the hose

The Hose Clamp is an OEM part for Whirlpool washing machines. This clamp secures the hose in place, ensuring a tight connection and preventing leaks during operation. It is essential for maintaining the integrity of the washing machine's water system, securing hoses that carry water to and from the washer.

Common causes of a bad hose clamp include rust, physical damage, or loosening from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Water leaks around the hose connection points
• The hose slipping off the fitting
• Visible rust or wear on the clamp
• Difficulty in tightening the clamp to secure the hose

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

The Hose Clamp is an OEM part for Whirlpool washing machines. This clamp secures the hose in place, ensuring a tight connection and preventing leaks during operation. It is essential for maintaining the integrity of the washing machine's water system, securing hoses that carry water to and from the washer.

Common causes of a bad hose clamp include rust, physical damage, or loosening from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Water leaks around the hose connection points
• The hose slipping off the fitting
• Visible rust or wear on the clamp
• Difficulty in tightening the clamp to secure the hose

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

This part has been discontinued by the manufacturer and is no longer available.

The Mounting Stem Repair Kit is an OEM part for Whirlpool washing machines. It includes all necessary components to repair the mounting stem, which is a critical part of the washer's tub support system. Comes with the hub assembly, seal, and spanner nut. 6-2040130 should also be replaced at the same time. A spanner wrench is required to complete the repair TB123B.

Symptoms of a bad mounting stem include:

• Excessive noise or vibration during the spin cycle.
• The washer tub appearing loose or off-balance.
• Leakage around the central area of the washer, indicating a possible seal failure.

Causes of a bad mounting stem can include wear and tear from normal usage, especially with heavy loads, or corrosion and material fatigue that weaken the stem's integrity.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This part has been discontinued by the manufacturer and is no longer available.

This part has been discontinued by the manufacturer and is no longer available.

The Washer Drive Motor is an OEM part for Whirlpool washing machines, designed to convert electrical energy into mechanical motion to drive the washing machine drum. This motor is a pivotal component in ensuring your washer operates smoothly across various cycles, whether it's agitating clothes in the wash cycle or spinning them dry. 

Causes of a bad Washer Drive Motor can range from wear and tear over time, overheating due to overloading or obstructed movement, and electrical failures such as short circuits or damaged wiring.

Symptoms of a failing Washer Drive Motor include:

• The washer not agitating or spinning correctly
• A burning smell or unusual noises during operation
• The washing machine failing to start

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Washer Drain Pump is an OEM part for Whirlpool washing machines. It is responsible for removing water from the washing machine during the drain cycle, ensuring efficient and complete water removal.

Causes of a bad drain pump can include blockages from debris or foreign objects, electrical failures, or wear and tear from regular use. Over time, these issues can impede the pump's ability to function properly.

Symptoms of a bad drain pump include:

• Water not draining from the washer
• Unusual noises during the drain cycle
• Error codes related to draining issues
• Leaks coming from the pump area

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Note: Fits 2 belt design Maytag washers. Check belts for wear; if needed order 12112425.

The Washer Drain Pump is an OEM part for Whirlpool washing machines. It is responsible for removing water from the washing machine during the drain cycle, ensuring efficient and complete water removal.

Causes of a bad drain pump can include blockages from debris or foreign objects, electrical failures, or wear and tear from regular use. Over time, these issues can impede the pump's ability to function properly.

Symptoms of a bad drain pump include:

• Water not draining from the washer
• Unusual noises during the drain cycle
• Error codes related to draining issues
• Leaks coming from the pump area

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Note: Fits 2 belt design Maytag washers. Check belts for wear; if needed order 12112425.

This factory spring kit restores the designed tension and return action in the affected assembly so moving parts operate smoothly, stay in position, and wear evenly over time.

• Provides the correct counterforce to position or balance components
• Maintains steady tension to prevent drift, slamming, or misalignment
• Helps reduce squeaks, chatter, or uneven movement from fatigued springs
• Typical signs of failure: weak return, inconsistent movement, excess noise, or visible spring damage

• Disconnect power; shut off water or gas before servicing
• Wear eye protection—springs are under tension
• Note original spring anchor points and replace all springs in the kit as a set
• Use appropriate pliers or a hook tool; verify smooth operation before reassembly

Screw: 8-16 x 3/8 inch.

A replacement nut-lock used to secure fasteners and keep panels or components from backing off due to vibration. Simple, durable hardware that restores a secure connection and reduces rattling or loose parts. What it does:

• Secures a mating bolt or stud to prevent loosening from vibration or movement
• Restores a solid attachment for panels, brackets, or assemblies that may come loose
• Helps eliminate symptoms such as rattling, vibrating, or intermittent panel movement
• Suitable where a locking fastener is required to maintain a reliable connection

• Disconnect power and follow appliance safety procedures before starting work
• Locate the matching stud or bolt and remove the old fastener if present
• Use the correct-size wrench or socket and tighten until the nut-lock seats; avoid over-tightening
• Inspect threads and mating hardware for damage; replace damaged components

The Whirlpool screw is an OEM replacement part responsible for securing various components or parts on different types of Whirlpool appliances. The screw is designed to provide a secure and reliable fastening connection, ensuring that different parts of the appliance stay in place. It is commonly used in different locations within the appliance, such as the cabinet, panels, or other structural elements.

This part fixes the following symptoms:

• Loose or wobbly components within the appliance
• Panels or parts that are not securely attached
• Rattling or unusual noises due to loose parts
• Damaged or missing screw

The Whirlpool screw can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The Leveling Leg Pad is an OEM replacement part for Whirlpool washing machines. This small but essential component fits beneath the leveling legs, providing stability and preventing the appliance from moving or vibrating excessively during operation. It also protects flooring surfaces from potential scratches or damage.

Symptoms of a bad Leveling Leg Pad include:

• Increased vibration or noise during the wash or spin cycle
• The washing machine wobbling or becoming unsteady
• Visible wear, cracks, or damage to the pad

Causes of a failing Leveling Leg Pad can include wear and tear from prolonged use, exposure to moisture, or excessive weight causing deformation. Replacing worn pads helps maintain the appliance's balance and efficiency.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

For the leveling leg order 22003428.

This part has been discontinued by the manufacturer and is no longer available.

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This part has been discontinued by the manufacturer and is no longer available.

This internal hose connects the washer's outer tub to the drain pump, channeling wash water during the drain cycle. Replacing a worn or leaking hose helps prevent puddles and supports reliable draining performance.

• Routes water from the outer tub to the drain pump inside the washer
• Maintains a sealed path; cracks or loose connections can lead to leaks
• Visible splits, soft spots, swelling, or aging can cause water under the unit
• Obstructions or internal collapse may contribute to slow or incomplete draining

• Disconnect power and turn off water supply before servicing
• Expect residual water; use towels or a pan when removing the old hose
• Note hose routing and clamp positions; seat fully on each port and secure with appropriate clamps
• Run a quick fill/drain test and check all connections for leaks after installation

The Pump and Drive Belt Kit is an OEM replacement part for Whirlpool washing machines. The Pump and drive belt kit is responsible for helping to drain water from the washer drum during the wash cycle. The pump and drive belt kit works by powering the washer's pump to remove water from the drum and out of the washer. The drive belt provides the power to turn the pump, while the pump helps to drain the water. The kit includes 1 pump belt and 1 drive belt.

This part fixes the following symptoms:

• Standing water in the washer drum
• Ineffective or non-existent water drainage
• Potential water damage or flooding caused by a faulty pump or drive belt

Causes of needing to replace the pump and drive belt kit include normal wear and tear over extended use, exposure to debris or foreign objects, or physical damage from impact or mishandling.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washer models. 

The Pump and Drive Belt Kit is an OEM replacement part for Whirlpool washing machines. The Pump and drive belt kit is responsible for helping to drain water from the washer drum during the wash cycle. The pump and drive belt kit works by powering the washer's pump to remove water from the drum and out of the washer. The drive belt provides the power to turn the pump, while the pump helps to drain the water. The kit includes 1 pump belt and 1 drive belt.

This part fixes the following symptoms:

• Standing water in the washer drum
• Ineffective or non-existent water drainage
• Potential water damage or flooding caused by a faulty pump or drive belt

Causes of needing to replace the pump and drive belt kit include normal wear and tear over extended use, exposure to debris or foreign objects, or physical damage from impact or mishandling.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washer models. 

This replacement seal restores a tight, leak-resistant barrier between mating parts inside your appliance. Replacing a hardened or damaged seal helps stop seepage and keeps the system operating as designed. What it does:

• Forms a tight barrier between components to contain fluids and prevent leaks
• Helps maintain proper pressure/flow at the sealed joint
• Reduces risk of moisture damage around the connection point
• Common signs it's worn: drips or puddles, dampness around the joint, musty odors, visible cracking or flattening of the old seal

• 1 seal

• Disconnect power and shut off water or gas supplies before servicing
• Access the sealed joint; remove the old seal and clean mating surfaces thoroughly
• Lightly lubricate with manufacturer-approved lubricant; install without twisting
• Reassemble, restore utilities, and check closely for leaks during initial operation

This part has been discontinued by the manufacturer and is no longer available.

This Torx-head screw set replaces worn, stripped or missing Torx fasteners used throughout the appliance to keep panels and components securely fastened. Restoring proper fasteners reduces vibration and prevents loose parts. What it does:

• Secures control panels, trim pieces or internal components that use Torx-head screws
• Replaces damaged or corroded Torx screws that can cause rattling or misalignment
• Helps restore proper fit and finish after repairs or disassembly
• Uses a Torx drive for a more secure torque transfer than standard Phillips heads

• Unplug the appliance or disconnect power before starting any repair
• Use the correct-size Torx driver to avoid stripping the screw head
• Tighten screws snugly but avoid over-torquing to prevent thread or part damage
• Keep removed screws organized and compare to the new set before installation

This factory fastener secures appliance components such as panels, brackets, and trim. Replacing a missing or stripped screw restores a tight fit, reduces rattling, and helps keep assemblies aligned for reliable performance.

• Fastens appliance parts to maintain structural integrity and alignment
• Helps address symptoms like loose or vibrating panels, gaps, or hardware that won't stay tight
• Replaces lost, damaged, or corroded fasteners during repairs or reassembly
• OEM-matched thread and fit for the specified location

• Disconnect power; shut off gas or water supplies before servicing
• Replace one screw at a time to preserve alignment of parts
• Start threads by hand to avoid cross-threading; tighten snugly without over-torquing
• Use the correct driver size/type specified for your model

This adjusting nut threads onto an eyebolt to set and lock an adjustment point. It helps maintain proper tension or alignment in the mechanism so the appliance operates smoothly without the setting drifting over time. What it does:

• Threads onto an eyebolt to fine-tune and secure an adjustment
• Helps prevent vibration from loosening the setting
• Replaces a stripped, rounded, or missing nut so adjustments hold
• Visual cues for replacement include damaged threads or worn hex flats

• 1 adjusting nut

• Disconnect power; turn off water or gas supply if applicable
• Components attached to eyebolts may be under spring or mechanical tension—support and relieve tension before removal
• Mark or measure the original setting to match during reassembly
• Start by hand to avoid cross-threading; tighten securely without over-torquing

The Motor Mount Roller and Spring Kit is an OEM part for Whirlpool washing machines. This kit includes the motor mount, roller, and spring, which work together to support and stabilize the motor during the wash and spin cycles. These components are crucial for minimizing vibrations and ensuring the motor runs smoothly and efficiently.

Causes of a bad motor mount, roller, or spring can include normal wear and tear over time, heavy or unbalanced loads that put extra stress on the components, and accidental damage or impact. 

Symptoms of a bad motor mount, roller, or spring include:

• Excessive noise during the wash or spin cycle
• Vibrations or shaking of the washing machine
• The drum not spinning properly
• Motor misalignment or poor performance

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This part has been discontinued by the manufacturer and is no longer available.

The Water Level Pressure Switch Hose is an OEM part for Whirlpool washing machines. It connects the water level pressure switch to the tub, allowing the switch to accurately detect and control the water level during washing cycles.

Common causes of a bad pressure switch hose include wear and tear over time, blockages from detergent buildup or debris, and kinks or cracks that disrupt the pressure flow.

Symptoms of a bad Water Level Pressure Switch Hose include:

• Incorrect water levels during wash cycles
• The washing machine not filling or overfilling
• Leaks around the hose area
• Error codes related to water level issues

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Specs: 10 - 16 x .375

Leg, adjustable (w/nut)

Size: 10-32

The Hose Clamp is an OEM part for Whirlpool appliances. It secures hoses in place, ensuring a tight connection and preventing leaks in various systems such as washing machines, dishwashers, and refrigerators. This clamp is crucial for maintaining the integrity of the water or air lines it secures.

Causes of a bad hose clamp include wear and tear over time, exposure to water and detergents, or mechanical stress from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Leaks at the hose connection points
• Hoses slipping off the connections
• Visible rust or damage on the clamp
• Reduced appliance efficiency due to leaks

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This small retaining clip secures components in place inside the appliance, helping prevent movement, vibration, and premature wear. Replace a bent, fatigued, or missing clip to restore a solid, factory-tight hold.

• Holds panels, brackets, or tubing securely in their mounts
• Helps maintain alignment to reduce rattles, rubbing, or intermittent issues
• Common signs of failure: missing clip, loose fit, buzzing/vibration, parts that won't stay seated
• Restores proper retention after service, transport, or vibration-related fatigue

• Disconnect power and shut off gas/water before servicing
• Note the original clip's orientation; remove with needle-nose pliers
• Seat the new clip fully—do not over-bend; spring tension provides the hold
• Test operation before reassembly

This replacement screw secures appliance panels and components to restore proper fit and reduce vibration. A straightforward fastener that helps keep parts aligned and prevents noise or loose trim from worsening. What it does:

• Fastens panels, brackets, or trim pieces to the appliance frame
• Helps stop rattling or vibration caused by loose or missing hardware
• Restores proper alignment where original screw has been lost or damaged
• Works wherever the OEM screw specification is required for secure mounting

• Turn power off and unplug the appliance before working on it
• Use the correct screwdriver or bit to avoid stripping the head
• Thread carefully and avoid overtightening to prevent damage to threads or plastic parts
• Keep removed fasteners organized so you reinstall the correct pieces

2 ounce bottle

The High-Temperature Adhesive Tube is an OEM part for Whirlpool appliances. This adhesive is specifically formulated to withstand extreme temperatures, making it ideal for securing components in ovens, dryers, and other high-heat environments. It is commonly used to seal or repair gaskets, felt seals, and other parts that require a durable bond to maintain integrity under thermal stress.

Symptoms of a need for High-Temperature Adhesive include:

• Loose components or seals within high-heat appliances
• Heat escaping from appliance seals
• Unusual noises due to parts shifting that are normally secured

Causes for the use of high-temperature adhesive can stem from normal wear and tear that loosens components or degradation of previous adhesive applications due to prolonged exposure to high temperatures.

This product is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.