Skip to Content
  • time delivery images 2 Day Quick Delivery!
  • box-refresh images 365 Day Return Policy!
  • lovely images 15 million satisfied customers
  • boxes images Over 2.1 Million Parts In Stock
  • headphone imagesFree Tech Support!
  • google images Google Trusted Store

Admiral Belt

Best Seller
Admiral Dryer Drum Belt 92-1/4" 4-Rib
Genuine Whirlpool part
By: Whirlpool
Part Number: 341241

Get your dryer spinning smoothly again - install the Whirlpool 341241 OEM Drum Belt in minutes.

Why this belt?

  • Exact factory spec: 92 ¼-inch length × ¼-inch width, 4 ribs / 3 grooves - built to Whirlpool standards, not a generic copy.
  • Broad compatibility: Fits most Whirlpool-made dryers - Kenmore 110-series, Roper, Estate, Maytag, KitchenAid, Admiral, Crosley, Amana & more.
  • Quiet, durable rubber: Reinforced EPDM resists cracking and stretch for years of reliable tumbling.

Fixes these common dryer problems

Problem How the belt solves it
Drum won’t turn Transfers motor rotation to drum
Loud squealing / thumping Replaces stretched or frayed belt
Burning-rubber smell New belt stops slippage & heat build-up
Damp clothes / long cycles Restores correct drum speed & airflow


DIY install — about 15 minutes

  1. Unplug dryer; remove lint screen housing & front panel.
  2. Release belt tension at idler pulley; lift drum slightly to slide old belt off.
  3. Loop new belt around drum, idler pulley and motor pulley (ribbed side down).
  4. Re-assemble, run test cycle - enjoy quiet, consistent tumbling.

This part fixes the following symptoms
  • Heat stays on after drum has stopped
  • Will not tumble
  • Touchpad does not respond
  • No heat or not enough heat
See more...
Do-It-Yourself Stories from Customers like You Broken dryer belt   Bob B. • St Louis , MO • September 12, 2015

Unpluged dryer first. Then took the lint filter out and removed the two philips screws inside the lint filter lid. Then take a paint scraper just under the top of the dryer two inches from the left front corner and pushed in a little to release the snap connector and did the same on the right side. Then lifted top over. Then take a 5/16 socket or nut driver and remove the two screws on on the left inside panel, then the right side. Lean front out a little and remove the two wires one the back... Read more

More
$14.64
Compare At:
$17.42
You Save:
$2.78

IN STOCK
Ships Monday Guaranteed
Add to Cart
Best Seller
Admiral Washer Drive Belt
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10006384

The washer drive belt transfers motor power to the washer’s drive system so the basket spins and agitates. Replacing a stretched or broken belt helps stop squealing and slipping so cycles finish at proper spin speed.

What it does

  • Links the drive motor to the washer’s drive/pulley system
  • Restores spin and agitation when the belt is worn, glazed, or broken
  • Can reduce squeal or burning-rubber smells from belt slip
  • Helps prevent intermittent or no-spin conditions

What’s included
One drive belt.

Install notes

  • Unplug power; turn off water
  • Tip the washer back; remove the bottom shield/cover if present
  • Route the belt over the motor and drive pulleys; rotate by hand to seat fully
  • Inspect pulleys/drive parts for wear; run a spin or calibration test after install

This OEM Whirlpool belt is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washer models.

Do-It-Yourself Stories from Customers like You Whirlpool Cabrio washer made a loud noise during the spin cycles it also was very noisy while washing   Ralph N. • Spring , TX • October 25, 2018

This was my first attempt, ever, to repair a washing machine. After some internet research on the problems, I was able to determine that the shaft seal on the gearcase probably was leaking water into the gearcase with each use. No water was ever found on the floor, but when I turned the washer over to inspect the gearcase, I found a black, oily residue on the outside of it along with the same residue on the pulleys, the belt and the motor. I ordered a new gearcase, shift actuator, splutch... Read more

More
$28.26
Compare At:
$33.63
You Save:
$5.37

IN STOCK
Ships Monday Guaranteed
Add to Cart
Best Seller
Admiral Dryer Drum Belt
Genuine Whirlpool part
By: Whirlpool
Part Number: WP33002535

The Dryer Drum Belt is an OEM replacement part for Whirlpool electric dryers. This belt rotates the tumbling drum to fluff and dry clothing loads efficiently. Continuous, uninterrupted drum movement is necessary for effective drying performance. This high-quality belt features 4 grooves and 5 ribs, with a width of 5/16" and a length of 91 5/8".

Causes of a faulty belt include breakage from age, cracks developing as rubber dries out, or slipping off the pulleys due to looseness or worn grooves.

Symptoms of a bad dryer belt include:

  • Drum fails to turn or rotates slowly during cycles
  • Loud squealing, screeching noises originating from inside  
  • Smoky smells from belt slipping against fast-turning pulleys
  • Possible jolts, jerks or prevented operation of dryer 

This belt is also compatible with KitchenAid, Maytag and Jenn-Air models too.

Do-It-Yourself Stories from Customers like You Dryer squealing on startup   Sandy R. • Manhattan , KS • September 08, 2015

I replaced the belt, belt tension pulley, both dryer drum roller axles and both drum support rollers. Although I bought 2 tumbler bearing kits, because those still look good I am saving them for when they go bad. The videos were fantastic! I also took pictures as I went of wiring so there would be no question where things went when reassembling. It should be noted some models have extra terminals near the sensor terminals... just be aware and look closely/take pics as you are taking things... Read more

More
$25.95
Compare At:
$30.88
You Save:
$4.93

IN STOCK
Ships Monday Guaranteed
Add to Cart
Best Seller
Admiral Dryer Drum Belt
Genuine Whirlpool part
By: Whirlpool
Part Number: WPY312959

The Dryer Drum Belt is an OEM replacement part for Whirlpool dryers. It is a crucial component that connects the dryer's motor to the drum, allowing the drum to rotate and tumble the clothes during the drying cycle.

Symptoms of needing to replace the dryer drum belt include:

  • The dryer drum not spinning or rotating
  • Loud squeaking or grinding noises during the drying cycle
  • Excessive vibration or shaking from the dryer
  • Clothes taking longer to dry or remaining damp

Causes of a faulty drum belt can include normal wear and tear over time, exposure to excessive heat or lint buildup, or physical damage due to impact or mishandling.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dryer models.

This part fixes the following symptoms
  • Will not tumble
See more...
Do-It-Yourself Stories from Customers like You Dryer belt broke from over 30 years of wear in a maytag   Keith K. • Phoenix , AZ • October 18, 2014

I watched your initial video which gave me some insight into the repair. I removed power from the dryer and positioned it for maintenance. Since my dryer was a Maytag, I needed to remove to two front bottom Phillips screws from the front panel of the dryer prior to pulling the panel and door assy. from the unit. The top of the dryer now needs to be removed. Two screws, one on each side holds the top of the dryer in place accessible from within and under the top of the dryer. Once those two... Read more

More
$24.95
Compare At:
$32.19
You Save:
$7.24

IN STOCK
Ships Monday Guaranteed
Add to Cart
Best Seller
Admiral Dryer Belt
Genuine Whirlpool part
By: Whirlpool
Part Number: WP40111201

The Belt is an OEM replacement part for Whirlpool dryers that is responsible for connecting the motor to the drum to allow it to tumble. Over time, dryer belts can stretch, wear out, or even break, leading to a drum that won't turn and clothes that don't dry properly. Length: 93 3/8" Width: 3/8" has 5 ridges.

Symptoms of a bad Dryer Belt include:

  • The dryer motor running but the drum not turning.
  • A squealing or thumping noise coming from the dryer.
  • The dryer not starting at all.

Causes of failure can include regular wear and tear from the dryer's operation, overloading the dryer beyond its capacity, which puts extra strain on the belt, or a misalignment that causes uneven wear. 

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

This part fixes the following symptoms
  • Will not tumble
See more...
Do-It-Yourself Stories from Customers like You The dyer belt and dryer belt tension pulley needed to be replaced   Freddrick G. • Lawrenceville , GA • July 30, 2015

I went to the local Home Depot and Lowes, but they did not have the parts because they do not carry parts for the items they actually sell to people. Jumped on the phone and did a quick search for parts and came across appliancepartspros.com. I put in the make and model of my dryer and all the parts for the dryer where listed. I ordered the items on a Wednesday night. I opted for the two day shipping. I thought the items would be at my house by Friday but they did not arrive until Monday. I... Read more

More
$14.64
Compare At:
$25.35
You Save:
$10.71

IN STOCK
Ships Monday Guaranteed
Add to Cart
Best Seller
Admiral Pump And Drive Belt Kit
Genuine Whirlpool part
By: Whirlpool
Part Number: 12112425

The Pump and Drive Belt Kit is an OEM replacement part for Whirlpool washing machines. The Pump and drive belt kit is responsible for helping to drain water from the washer drum during the wash cycle. The pump and drive belt kit works by powering the washer's pump to remove water from the drum and out of the washer. The drive belt provides the power to turn the pump, while the pump helps to drain the water. The kit includes 1 pump belt and 1 drive belt.

This part fixes the following symptoms:

  • Standing water in the washer drum
  • Ineffective or non-existent water drainage
  • Potential water damage or flooding caused by a faulty pump or drive belt

Causes of needing to replace the pump and drive belt kit include normal wear and tear over extended use, exposure to debris or foreign objects, or physical damage from impact or mishandling.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washer models. 

This part fixes the following symptoms
  • Spins slowly
  • Burning smell
  • Pumps but will not spin
  • Noisy
See more...
Do-It-Yourself Stories from Customers like You Maytag clothes washer would not spin or drain   Ben M. • Wallingford , CT • September 29, 2018

The washer was on, and I heard a faint humming sound in the laundry room. I went in and opened the washer and it was full of soapy water in the middle of its cycle and was not agitating. I also smelled a faint burning smell. At this point I figured the problem was a bad motor, as the washer is more than 20 years old. I have fixed it twice before, because the first time, the repairman said I should keep this washer going as long as possible. It was made to last with a metal drum, unlike newer... Read more

More
$32.43
Compare At:
$44.49
You Save:
$12.06

IN STOCK
Ships Monday Guaranteed
Add to Cart
Best Seller
Admiral Washer Drive Belt
Genuine Whirlpool part
By: Whirlpool
Part Number: WP21352320

The Washer Drive Belt is an OEM part for Whirlpool washing machines. It is crucial for transmitting the power from the motor to the drum, enabling the washing machine to tumble and spin during the wash and spin cycles. The drive belt wraps around the motor and drum pulleys, providing the necessary traction and tension to operate efficiently.

Causes of a bad Washer Drive Belt can include stretching over time, which reduces its efficiency to grip the pulleys properly, or fraying and cracking due to age and normal wear and tear. Misalignment or improper installation can also lead to premature belt failure.

Symptoms of a bad Washer Drive Belt include:

  • The washing machine failing to spin or agitate.
  • A burning smell or unusual noises during operation, indicating slippage or rubbing.
  • Visible signs of wear like cracks, fraying, or noticeable looseness on the belt.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This part fixes the following symptoms
  • Burning smell
  • Will not agitate
  • Spins slowly
  • Pumps but will not spin
See more...
Do-It-Yourself Stories from Customers like You The drive belt on my maytag washing machine was worn out   Donnie B. • Campobelly , SC • July 23, 2014

I Purchased a new belt and replaced it. If I had not watched the video telling me how it is done the job would have been much more difficult. After watching the video I changed the belt in less than 2 minutes. I ordered the belt from Appliance Parts Pros and got it the next day. I am thankful that when I started my search I landed on your web site. Thanks for the quick service and the video. Read more

More
$15.95
Compare At:
$23.33
You Save:
$7.38

IN STOCK
Ships Monday Guaranteed
Add to Cart
Best Seller
Admiral Washer Drive Belt
Genuine Whirlpool part
By: Whirlpool
Part Number: WP22003483

The Washer Drive Belt is an OEM part for Whirlpool washers. This belt connects the washer's motor to the drum, enabling the drum to rotate during the wash and spin cycles. It plays a crucial role in the washer's operation.

Causes of a bad washer drive belt can include wear and tear, stretching, or damage from overloading the washer.

Symptoms of a bad washer drive belt may include:

  • Drum not spinning or agitating.
  • Unusual noises coming from the washer during operation.
  • Belt slipping or appearing worn.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

Do-It-Yourself Stories from Customers like You Loud knocking and rattle while in spin cycle.   Daniel K. • Grafton , WI • July 30, 2017

18 year old Maytag Atlantis top load washer had a load knocking and rattle sound with excessive vibration when the tub was spinning, but not when it was agitating. They was no water leaking. I took the front panel off and carefully listened while I ran a cycle and the loud sound sounded like it was coming from the drain pump. So I took off the drive belt and noticed that it was glazed and that there was belt material on the drain pump and tub transmission pulleys. I removed the drain pump and... Read more

More
$32.95
Compare At:
$39.21
You Save:
$6.26

IN STOCK
Ships Monday Guaranteed
Add to Cart
Best Seller
Admiral Drive Belt
Genuine Whirlpool part
By: Whirlpool
Part Number: W11239857

The Drive Belt is an OEM part for Whirlpool washing machines. This belt works to spin the washing machine tub and agitate clothes during cycles. It transmits rotational power from the motor to the inner tub and outer tub.

Causes of a bad drive belt can include wear and over time usage, exposure to harsh detergents or fabric softeners that may cause premature wear and cracking, or damage from overloading the washer.

Symptoms of a bad drive belt include:

  • The washer tub not spinning or rotating very slowly
  • Loud squealing, squeaking or grinding noises when operating
  • The belt slipping off the pulleys
  • Vibrating that causes the washer to walk or move during cycles

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Do-It-Yourself Stories from Customers like You The metal om metal sound at the end of the spin cycle. Also found gearcase oil covering the inside of the drive belt plastic cover.   Harry S. • Belvidere , NJ • May 23, 2023

Replaced the Gearcase assembly which is a sealed unit that is not serviceable. Also replaced the clutch and belt because they were covered in gearcase oil. Read more

More
$44.95
Compare At:
$53.04
You Save:
$8.09

IN STOCK
Ships Monday Guaranteed
Add to Cart
Best Seller
Admiral Belt And Isolator Kit
Genuine Whirlpool part
By: Whirlpool
Part Number: 12001788

The Belt and Isolator Kit is an OEM part for Whirlpool washing machines. This kit includes a drive belt and isolators that work together to transfer motion from the motor to the washer drum while dampening vibrations. 

Over time, the belt can wear out, stretch, or break due to regular use, heavy loads, or friction. The isolators may also deteriorate, losing their ability to absorb shocks effectively.

Symptoms of a bad Belt and Isolator Kit include:

  • The drum not spinning or agitating
  • Excessive vibration or noise during operation
  • The washer failing to start or complete cycles

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This part fixes the following symptoms
  • Will not agitate
  • Spins slowly
  • Burning smell
  • Pumps but will not spin
See more...
Do-It-Yourself Stories from Customers like You Noisy spin cycle   Gregory E. • Halifax , PA • April 17, 2017

I just wanted to put my experience here for all to see. I have a Maytag Neptune, MAH5500BWW, one of the original ones. I bought it back in 2002 and it has done many many loads of wash faithfully. So when the bearings started to get loud I thought it best to replace them, the seal kit and the belt. I did my research as best I could and decided to order the OEM parts from an appliance supplier. If you are replacing the bearings, watch on line videos prior to performing the job. It will... Read more

More
$28.95
Compare At:
$34.45
You Save:
$5.50

IN STOCK
Ships Monday Guaranteed
Add to Cart

Looking to keep your home appliances running smoothly? Admiral belt replacement parts play a crucial role in the overall performance and longevity of your machines. These belts ensure that your Admiral washers and dryers operate efficiently, seamlessly transferring power to where it's needed most. They might seem like simple components, but Admiral parts are essential in maintaining the optimal functionality of your appliances.

Replacing worn-out belts with high-quality Admiral belt parts can prevent unexpected breakdowns and extend the lifespan of your equipment. Opting for OEM replacement parts ensures that you're getting the best fit and compatibility, as these are designed by the original manufacturer specifically for your appliance. This means you can trust in their quality and performance, and not worry about mismatched components causing issues down the line.

So, whether your Admiral washer or dryer is in need of a new belt, you can rest easy knowing that reliable, quality parts are readily available to keep everything running smoothly. Trust these essential components to restore and maintain your appliance's peak performance seamlessly.

More
  • boxes images Over 2.1 Million Parts In Stock
  • time delivery images 2 Day Quick Delivery!
  • box-refresh images 365 Day Return Policy!
  • headphone imagesFree Tech Support!
  • google images Google Trusted Store