Admiral Gasket & Seal

Note: For faucet adapter

The Gasket-FIP  is an OEM part for Whirlpool refrigerators, ensures an airtight seal around the door, preventing cold air from escaping and warm air from entering. This component contributes to the refrigerator's energy efficiency and cooling effectiveness, maintaining the optimal internal temperature to keep your food fresh longer. 

Causes of a bad Gasket-FIP can range from normal wear and tear, accidental damage, or deformation due to improper cleaning methods or exposure to extreme temperatures.  

Symptoms of a bad Gasket-FIP include:

• Noticeable gaps between the gasket and the refrigerator door or frame
• Condensation or frost buildup near the door edges
• The refrigerator working harder to maintain its internal temperature, potentially leading to increased energy bills
• The door not closing as smoothly or firmly as it should

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This door gasket seals the refrigerator/freezer door to help maintain proper temperature and reduce energy loss. A direct-fit replacement that restores the magnetic seal for better cooling performance. What it does:

• Re-establishes a tight seal around the door to keep cold air in and warm air out
• Helps reduce frost buildup and moisture inside the compartment
• Improves cooling efficiency and may reduce excessive run time from a failing seal
• Stops drafts and prevents food spoilage caused by a poor door seal

• One door gasket

• Clean the door frame and remove old gasket before installing the new one
• Warm or flex the gasket as needed for easier positioning; ensure the magnetic seal seats evenly around the perimeter
• Check hinge alignment and door closing after installation to confirm a complete seal
• Follow appliance power-off and safety precautions; refer to the appliance manual for model-specific instructions

This is the rear crisper seal that fits along the back edge of the refrigerator crisper compartment to help maintain the crisper enclosure and reduce air leakage. It restores a tighter seal for better humidity control and food storage. What it does:

• Replaces a worn or torn rear crisper gasket to help reduce cold air loss from the crisper area
• Helps maintain crisper humidity so produce stays fresher longer
• Prevents gaps that can cause uneven cooling or frost build-up near the drawer
• Can reduce draft noise or rubbing caused by a damaged seal

• One rear crisper seal (matches OEM part number)

• Remove the crisper drawer to access the rear seal before replacing
• Peel out the old seal and press the new seal firmly into the gasket channel; ensure an even, continuous fit
• Avoid using sharp tools that could damage the cabinet or new seal
• Unplug the refrigerator or switch off power if needed for safe access to nearby components

Condenser seal that cushions and seals the condenser assembly to the cabinet, helping reduce vibration and directing airflow for more consistent cooling performance and quieter operation. What it does:

• Cushions the condenser to reduce vibration and rattling noises
• Seals the condenser perimeter to help direct airflow through the condenser coils
• Helps prevent rubbing and abrasion between the condenser and cabinet
• A worn or missing seal can contribute to increased noise or reduced cooling efficiency

• Disconnect power to the appliance before beginning any repair
• Remove the lower access panel or kickplate to access the condenser area
• Peel out the old seal and press the new seal fully into the channel or onto the condenser flange for a snug fit
• Inspect condenser fins and surrounding parts during installation; do not use solvents or unapproved adhesives

This evaporator cove seal is the replacement gasket that helps keep the evaporator compartment sealed for efficient cooling and proper defrost drainage. It restores the evaporator cove barrier to help maintain temperature consistency. What it does:

• Seals the evaporator cove to limit air exchange between the evaporator area and the fresh food/freezer compartments
• Helps direct defrost water to the drain path and reduce water pooling inside the appliance
• Reduces frost buildup and cold-air loss around the evaporator area
• Commonly replaced when you see frost/ice buildup, interior water leaks, or uneven cooling

• Disconnect power before starting any repair to avoid shock or injury
• Remove shelves/food and allow the appliance to defrost if ice is present before replacing the seal
• Inspect the evaporator cover and mating surfaces; clean and dry surfaces for a proper seal
• Seat the seal evenly around the cove; avoid overstretching or sharp tools that could damage the gasket