Admiral Gasket & Seal

The Fresh Food Door Gasket is an OEM part for Whirlpool refrigerators. This gasket creates a seal around the refrigerator door, helping to maintain the internal temperature and keep the fresh food compartment cool. The gasket measures approximately 38.85" x 38.27".

You should replace this door gasket if it becomes worn out or damaged. Causes of a bad door gasket can include wear and tear over time, exposure to extreme temperatures, or physical damage from repeated opening and closing of the refrigerator door.

Symptoms of a bad door gasket include:

• Cold air escaping from the refrigerator
• Increased energy consumption
• Frost buildup around the door
• Difficulty closing the refrigerator door completely

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Seal is an OEM part for Whirlpool washing machines. This part provides a tight seal around the washer shaft, preventing water from leaking out of the tub during the wash cycle.

Causes of a bad shaft seal can include wear and tear over time, exposure to harsh detergents or cleaning agents, or damage from foreign objects that may have gotten into the washer. 

Symptoms of a bad shaft seal include:

• Water leaking from the bottom of the washing machine
• Excessive noise during operation
• Visible damage or wear on the seal
• Wet spots or puddles under the washer

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This door gasket runs around the perimeter of the door opening to create a dependable seal when closed. A proper seal helps limit air and moisture leaks, supporting stable internal conditions, reduced condensation, and efficient performance. What it does:

• Seals the door perimeter to block unwanted air and moisture infiltration
• Helps minimize condensation around the door and maintain consistent internal conditions
• Replaces gaskets that are torn, cracked, warped, or permanently compressed
• Can help when the door won't seal properly or you notice drafts, moisture, or temperature swings

• 1 door gasket

• Disconnect power if removing the door or working near electrical components
• Warm the gasket (soak in warm water or use low heat) to relax it before installation
• Press the gasket fully into the channel/retainer, ensuring corners are completely seated
• Check for uniform contact all around; adjust door alignment if needed and allow up to 24 hours for the gasket to conform

The Oven Door Seal is an OEM part for Whirlpool ovens. This seal is crucial for maintaining the oven’s efficiency by creating an airtight seal around the door, preventing heat from escaping during cooking. It helps ensure that the oven maintains the correct temperature, which is essential for even cooking and energy efficiency.

Common causes of a bad oven door seal include wear and tear from regular use, exposure to high temperatures, and damage from cleaning or handling.

Symptoms of a bad oven door seal include:

• Heat escaping from around the oven door
• Longer cooking times or uneven cooking
• The oven door not closing properly
• Visible cracks, tears, or deformation in the seal

This OEM part is also compatible with some Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Transmission Lower Lip Seal is an OEM part for Whirlpool washing machines. This seal plays a crucial role in preventing water leakage from the transmission area of the washing machine.

Symptoms of a bad transmission lower lip seal:

• Water leaks or puddles around the base of the washing machine
• Visible wear, cracks, or damage to the seal
• Rust or corrosion around the seal area

Causes of a faulty transmission lower lip seal can include general wear and tear over time, exposure to excessive heat or chemicals, or physical damage from impact or improper handling.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washing machine models. 

(Adhesive Sold Separately).To order adhesive use part number WPY055980.This Part Can Be Used As Both The Front And Rear Seal In Some Models

This door gasket seals the dishwasher door opening to keep wash water and moisture inside the tub. A fresh, flexible seal helps prevent leaks and improves cleaning performance by maintaining proper pressure and heat.

• Creates a watertight seal between the tub and door perimeter
• Helps prevent leaks at the bottom and sides of the door
• Helps resolve symptoms like water on the floor, moisture around the door, long dry times, or visible tears/flattening of the old gasket
• Restores proper door compression and wash chamber containment

• Disconnect power and turn off water supply before service
• Remove the old gasket from the channel; clean the groove of debris and residue
• Press the new gasket evenly into the channel, centering at the top and working down both sides
• Close the door to help seat the gasket; a short run cycle may help it conform

The Tub Cover Gasket is an OEM part for Whirlpool washing machines. This part creates a watertight seal between the tub cover and the tub, preventing water from leaking during the wash cycle. 

Causes of a bad gasket include exposure to harsh detergents, regular wear and tear, or improper installation. 

Symptoms of a bad tub cover gasket include:

• Water leaking from the washing machine
• Excessive moisture around the tub cover area
• Visible cracks or wear on the gasket
• Unusual noises during the wash cycle due to improper sealing

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Color: White. Size: 31 1/2 inches 41 inches. For black order WP61004017.

This white door gasket seals the perimeter of the refrigerator door. It helps keep cold air in and humid air out, supporting stable temperatures and reducing frost and moisture around the door opening. What it does:

• Maintains an airtight seal between the door and cabinet
• Replaces a torn, cracked, shrunken, or deformed gasket that won't seal
• Helps address condensation around the door, frost/ice buildup, temperature fluctuations, or a door that won't close flush

• 1 door gasket (white)

• Unplug the appliance before servicing
• Warm the new gasket (soak in warm water or use low, indirect heat) to relax kinks for easier fit
• Start at the corners and work evenly around the door; on screw-retained liners, loosen screws, seat the gasket lip, then retighten
• Close the door and check the seal; smooth out waves and allow the gasket to conform over the next 24 hours

This refrigerator door gasket seals the door to the cabinet to keep cold air in and moisture out. Replacing a worn or deformed gasket restores a reliable seal, steadier temperatures, and more efficient performance.

• Creates an air-tight seal around the door perimeter
• Helps maintain correct temperatures and reduce frost or condensation
• Supports proper door closing and overall cooling efficiency
• Replace if the gasket is torn, cracked, warped, hardened, or leaves gaps; if the door pops open; or if you see moisture/frost along the door edge

• Disconnect power; remove items from the door bins for access
• Pull the old gasket from the retainer; transfer/loosen corner screws if applicable
• Warm the new gasket (hot water or low-heat hair dryer) to relax it; seat the lip evenly, corners first
• Close the door and check for uniform contact; adjust with gentle heat and by leveling/hinge alignment if needed; allow up to 24 hours for the gasket to fully conform

This dishwasher water deflector redirects spray back into the tub at the front edge, helping prevent splash-over and leaks during cycles. Replace a cracked, warped, or missing deflector to keep floors dry and wash performance consistent.

• Directs wash water away from the door opening and front corners
• Helps reduce leaks and puddles at the bottom front of the dishwasher
• Restores proper containment when the original deflector is deformed, loose, or missing
• Common symptoms include water on the floor at the front, drips during cycles, or visible damage to the deflector

• Disconnect power and turn off the water supply before servicing
• Open the door to access the front/tub area; remove the old deflector
• Clean the mating area and seat the new deflector fully and evenly
• Run a short test cycle and check for leaks

This horizontal oven door seal lines the top and bottom edges of the door opening to keep heat contained inside the cavity. Replacing a worn seal restores stable temperatures, more efficient preheating, and consistent baking results.

• Seals the oven opening along the top and bottom edges to reduce heat loss
• Helps maintain set temperature and overall cooking performance
• Replaces cracked, frayed, flattened, or brittle horizontal gasket
• Common signs include visible gaps, heat escaping around the door, longer preheat times, and temperature fluctuations

• Disconnect power and allow the oven to cool completely before servicing
• Open the door and carefully pull the old seal straight out of the retainer
• Note clip/retainer positions as you remove the old seal and reuse them as designed
• Press the new seal evenly into place without stretching; ensure corners are fully seated for a uniform seal

This refrigerator door gasket replaces a worn seal to restore a tight, even closure around the door. A proper seal keeps cold air in and moisture out, helping maintain temperature, reduce frost, and minimize run time. What it does:

• Forms a tight seal between the door and cabinet frame
• Helps maintain set temperatures and reduce moisture intrusion
• Resolves frost or condensation at the door and frequent compressor cycling
• Common signs: torn, cracked, or warped gasket; gaps; door not sealing smoothly

• Includes: 1 door gasket

• Disconnect power before servicing; remove or secure contents for safety
• On many models, loosen the inner-liner screws or pull the old gasket from the retainer/channel to remove
• Warm the new gasket (warm water or low heat from a hair dryer) to relax shipping folds
• Seat corners first, then press the rest into the retainer; verify seal with a paper-slip test and adjust as needed

This door seal fits around the dryer door opening to keep heat and moisture inside the drum. Replacing a worn seal restores airflow, improves drying performance, and helps prevent lint and warm air from escaping around the door.

• Seals the door perimeter to maintain proper airflow and temperature inside the drum
• Reduces heat and moisture loss that can lead to longer dry times
• Helps contain lint and dust around the door opening
• Replace if the seal is torn, brittle, flattened, missing sections, or if you feel warm air or see lint escaping around the door

• Disconnect power and allow the dryer to cool before servicing
• Remove the old seal and clean the door surface so the new seal seats flat
• Align and press the new seal evenly around the opening; avoid stretching
• Close the door to confirm latch engagement and an even seal; run a short test cycle to check for leaks

Kit contains 2 pads, 1 right glide, 1 left glide, and instruction sheet. Support brace no longer included.