Admiral Gasket & Seal

This rubber seal creates a tight barrier between mating components to keep water contained and stop drips. Replacing a flattened or cracked seal helps prevent leaks and protects nearby parts from moisture-related damage. What it does:

• Forms a watertight gasket between two parts in the assembly
• Helps prevent drips or seepage at the connection point
• Restores proper compression when the original seal hardens or deforms
• Common signs of failure: leaks, dampness, or visible cracking/flattening of the old seal

• 1 rubber seal

• Disconnect power; for water-bearing assemblies, shut off the water supply
• Access the seal location per your service information and note orientation/depth before removal
• Clean mating surfaces; lightly moisten the new seal with water or mild soap to ease installation
• Ensure the seal is fully seated, reassemble, and test for leaks

This door seal replaces a worn or damaged gasket around the oven door, creating a tight barrier between the door and the front frame. A fresh seal helps the appliance heat efficiently and maintain steady cooking temperatures. What it does:

• Seals the gap between the door and oven frame to minimize heat loss
• Helps the oven preheat faster and hold set temperatures more consistently
• Replace if the gasket is torn, brittle, flattened, or frayed
• Common signs include heat escaping around the door edge and longer cook times

• 1 door seal

• Disconnect power and allow the oven to cool completely before beginning
• Open the door and carefully remove the old seal, noting its routing and attachment points
• Clean the mating surface to remove debris for a proper seal
• Install the new seal evenly without stretching; ensure all ends and anchors are fully seated

This cap seal creates a tight barrier between a cap and its mating surface in your appliance. Replacing a worn seal restores a secure, leak-resistant fit and helps maintain proper performance over time.

• Forms a tight seal where the cap seats to prevent leaks and seepage
• Helps maintain intended pressure/flow and keeps contaminants out
• Typical failure signs: drips or moisture around the cap area, loose cap fit, or a flattened/cracked seal
• Age, heat, and detergents/chemicals can harden or deform the seal

• Disconnect power and shut off water before servicing
• Remove the cap and note the seal's orientation
• Clean mating surfaces; seat the new seal fully without twisting
• Reinstall the cap and test operation, checking for a leak-free fit

This freezer door gasket replaces a worn or deformed seal to restore a tight, even closure on the freezer door. A proper seal keeps cold air in and humid air out, reducing frost buildup and temperature swings.

• Creates an air-tight seal between the freezer door and cabinet to contain cold air
• Helps maintain correct temperature and efficiency; reduces frost/ice around the door perimeter
• Symptoms of failure: tears, cracks, warping, gaps, or door not closing fully
• Presents as frost buildup, moisture/condensation, or warm spots in the freezer

• Disconnect power to the refrigerator before servicing
• Let the new gasket relax (lay flat; warm gently with hot water or a hair dryer) for easier fit
• Remove the old gasket from the retainer/channel; on screw-retained styles, loosen (do not remove) liner screws as needed
• Seat the new gasket evenly, starting at the corners; use gentle heat to smooth wrinkles and ensure a uniform seal all around

This is the front seal for the refrigerator's crisper compartment. It restores a tight barrier at the drawer's front edge so the crisper closes flush and maintains proper humidity to help keep produce fresh.

• Seals the front edge of the crisper to limit air leaks between the drawer and fresh food compartment
• Helps maintain intended humidity levels inside the crisper
• Restores smooth, flush closure of the drawer front
• Replace if the seal is torn, deformed, or missing; symptoms can include excess condensation or wilting produce

• Unplug the refrigerator and remove the crisper drawer
• Pull the worn seal off the crisper front/channel and clean the mating surface
• Warm the new seal in hot water to improve flexibility; press it evenly into place and ensure corners are fully seated
• Reinstall the drawer and verify proper alignment and closure

This agitator seal assembly sits at the agitator/drive-shaft pass-through to keep wash water inside the tub and away from the drive system. Replacing a worn seal helps stop center-post leaks and protects internal components from moisture.

• Seals the opening where the agitator/drive shaft passes through the tub or centerpost
• Helps prevent water from migrating into the centerpost/gearcase area
• Supports reliable agitation and spin by keeping contaminants out of the drive assembly
• Common symptoms of failure: water leaking from the center of the tub or beneath the washer, or rust/water tracks around the agitator hub

• Disconnect power and shut off water; wear gloves and eye protection
• Remove agitator cap and fastener, then lift the agitator to access the seal (procedure varies by model)
• Note the original seal orientation; clean mating surfaces and install the new seal squarely (lightly lubricate only if specified by the manufacturer)
• Reassemble and run a short fill/agitate test while observing for leaks

This coupler gasket creates a tight, leak-resistant seal at a coupler connection point, helping maintain proper operation of the assembly. Replace when the original gasket is worn, cracked, or flattened to prevent drips and seepage.

• Forms the seal between a coupler and its mating component
• Helps prevent water seepage and air intrusion at the joint
• Supports correct flow/pressure through the connection
• Common symptoms: drips at the fitting, moisture around the coupler, or needing to over-tighten to stop leaks

• Disconnect power and shut off water supply before servicing
• Relieve line pressure and place a towel to catch residual water
• Clean mating surfaces; seat the gasket squarely in the coupler recess
• Tighten fittings evenly; restore service and check for leaks

Size: 1-1/16 x 5/8 inch. Used for fill hose. For a 4 pack order 285448A

This injector seal fits the refrigerator's water injector. It restores a tight, watertight/airtight connection where the injector passes through the liner or mates to the fill tube, helping prevent leaks and frost around the opening.

• Seals the injector-to-liner/fill-tube connection to stop water seepage and air leaks
• Helps prevent frost/ice buildup near the injector area and fill tube freeze-ups
• Addresses issues from a cracked, shrunken, or missing seal
• Common symptoms: water drips at the back/freezer wall and frost near the fill opening

• Disconnect power and shut off the water supply before servicing
• Access the injector area (rear of freezer or cabinet, depending on model)
• Remove the old seal; press the new seal fully and evenly into place
• Reassemble, restore water/power, and check for leaks and proper fill

Hose washer and plastic insert for inlet hose. To order separately: for washer use WPY013783, for strainer use WP22002960.

This fresh food door gasket seals the refrigerator compartment door to keep cold air in and warm air out. Replacing a worn gasket restores a tight seal, improves temperature stability, and helps prevent condensation and frost around the door.

• Seals the perimeter of the fresh food (refrigerator) door to limit air leaks
• Helps maintain proper interior temperature and efficiency
• Typical symptoms of failure: door not closing or sealing fully; visible tears, gaps, or warping
• May cause moisture, sweating, or frost near the door gasket area

• Disconnect power before servicing
• Warm and relax the new gasket (soak in warm water or use low heat) to ease installation; do not overheat
• Clean the door's gasket channel; install starting at the corners and ensure even seating all around
• Close the door and check for uniform contact; use a paper-slip test to confirm the seal

This factory washer is used in appliance assemblies to distribute load under a fastener and maintain a secure, accurate fit. Replace a missing or damaged washer to restore proper stack-up and reduce vibration, noise, or loosening.

• Distributes load and provides proper spacing in the fastener assembly
• Helps keep bolts, screws, or nuts tight to minimize vibration and rattling
• Direct replacement when the original washer is worn, bent, cracked, or missing
• Typical signs include loose panels/brackets, recurring looseness after tightening, or new vibration after service

• Unplug the appliance; shut off water supply if working near hoses or valves
• Note the original hardware stack-up and reassemble in the same order
• Inspect mating surfaces and companion hardware; replace any damaged parts
• Tighten fasteners snugly per service guidance; avoid overtightening

This tub cover seal is a molded rubber gasket that helps keep wash water inside the tub and seals the cover area to prevent leaks. It restores a watertight seal and reduces seepage and debris buildup around the tub cover. What it does

• Seals the joint between the tub and tub cover to help prevent water leaks during cycles
• Cushions the cover edge to reduce noise and vibration
• Helps block lint, detergent residue and moisture from entering gaps
• Common symptoms: visible water on the floor near the tub cover, persistent dampness, or visible wear/cracking of the existing seal

• Disconnect power and water before beginning any repair
• Verify correct orientation and full seating of the gasket around the tub cover; replace if torn, deformed, or hardened
• Removal/installation may require access to the control panel or outer cabinet depending on model

Note: For faucet adapter