Admiral Refrigerator Parts

Best Seller

Genuine Whirlpool part

Admiral Water Valve Single

By: Whirlpool

Part Number: 4318047

The Single Water Valve is an OEM part for Whirlpool refrigerators. This valve controls the flow of water to the refrigerator’s ice maker and water dispenser, ensuring a consistent and reliable supply of water for ice production and dispensing.

Causes of a bad single water valve can include wear and tear over time, mineral buildup from hard water, or electrical malfunctions.

Symptoms of a bad single water valve include:

No water dispensing from the refrigerator
The ice maker not producing ice
Leaks around the valve area
Unusual noises when the water dispenser is activated

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This part fixes the following symptoms

Ice maker not making ice
Leaking

Do-It-Yourself Stories from Customers like You Leaking valve on ice maker Richard D. • Front Royal , VA • March 15, 2014

Order new valve Read more

$44.95

Compare At:: $53.04
You Save:: $8.09

IN STOCK

Ships Monday Guaranteed

Add to Cart

Best Seller

Genuine Whirlpool part

Admiral Defrost Thermostat (Refrigerator)

4.9 (14)

By: Whirlpool

Part Number: WP67004757

This refrigerator defrost thermostat senses evaporator temperature and controls power to the defrost heater. It melts frost when needed and shuts the heater off at a safe temperature to protect components and keep cooling performance steady.

Monitors coil temperature and opens/closes the defrost heater circuit
Terminates the defrost cycle at a safe cutoff to prevent overheating
Helps keep the evaporator clear of ice so air can circulate
Common symptoms: heavy frost on the freezer back wall/evaporator, warm refrigerator section, fan noise from ice, long run times with little or no defrosting

What's included: 1 defrost thermostat Install notes:

Disconnect power before service; use cut-resistant gloves
Access the evaporator behind the freezer rear panel and fully thaw any ice using heat-safe methods—never chip or pry
Reinstall the thermostat in the original location with firm metal-to-metal contact on the evaporator; route and secure wiring as originally
After reassembly, verify defrost operation and confirm unobstructed airflow

This part fixes the following symptoms

Freezer not defrosting
Freezer section too warm

Do-It-Yourself Stories from Customers like You Fridge not cooling freezer eval coil frosted over Tom A. • Ridgecrest , CA • June 10, 2016

Ended up being the defrost sensor. Ordered the heater and control board just in case. Started with the control board still didn't defrost. replaced the sensor and all is well. Super helpful tech staff answered all my questions... Read more

$65.64

Compare At:: $77.46
You Save:: $11.82

IN STOCK

Ships Monday Guaranteed

Add to Cart

Best Seller

Genuine Whirlpool part

Admiral Crisper Frame Support

5.0 (7)

By: Whirlpool

Part Number: WP12603701

The Crisper Frame Support is an OEM part for Whirlpool refrigerators. This part provides structural integrity and support for the crisper drawer, ensuring it remains stable and functions smoothly.

Causes of a bad crisper frame support can include regular wear and tear from frequent use, accidental impacts, or overloading the crisper drawer.

Symptoms of a bad crisper frame support include:

The crisper drawer not sliding in and out easily
Misalignment or instability of the crisper drawer
Visible cracks or breaks in the frame support
Difficulty in opening or closing the crisper drawer

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Do-It-Yourself Stories from Customers like You Broken parts Sean A. • Delaware , OH • July 21, 2017

Replacement of parts found on this site- great explanation and pictures as shown! Read more

$10.95

Compare At:: $13.14
You Save:: $2.19

IN STOCK

Ships Monday Guaranteed

Add to Cart

Best Seller

Genuine Whirlpool part

Admiral Light Bulb

4.7 (21)

By: Whirlpool

Part Number: W10857122

The Light Bulb is an OEM part for Whirlpool refrigerators. This part illuminates the water and ice dispenser area, providing visibility and ease of use, especially in low light conditions.

Over time, the light bulb can fail due to normal wear and tear, electrical surges, or damage from vibrations and impacts.

Symptoms of a bad light bulb include:

The dispenser area not lighting up when activated
Flickering or dim lighting
The bulb failing to turn on consistently

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Do-It-Yourself Stories from Customers like You My dryer was making noise James M. • Middletown , RI • September 19, 2014

I went on line and purchased all of the possible parts that could be worn out. I spent less than the service guy wanted to show up...The online videos were spot on. Two hours and it works like new! One of the best values on the Internet! Read more

$13.47

Compare At:: $16.03
You Save:: $2.56

IN STOCK

Ships Monday Guaranteed

Add to Cart

Best Seller

Genuine Whirlpool part

Admiral Water Line Union

4.8 (14)

By: Whirlpool

Part Number: WP2300868

The Water Line Union is an OEM part for Whirlpool refrigerators. It connects sections of the water line, ensuring a secure and leak-proof connection that facilitates the proper flow of water to the ice maker and water dispenser.

Causes of a bad water line union can include wear and tear from prolonged use, exposure to fluctuating temperatures, or physical damage from handling.

Symptoms of a bad water line union include:

Leaks or water pooling around the refrigerator
Reduced water flow to the dispenser or ice maker
Water line disconnections
Visible cracks or damage on the union

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This part fixes the following symptoms

Leaking

Do-It-Yourself Stories from Customers like You Leak/puddle on floor Barbara F. • Laurel , MD • April 22, 2014

Thought leak was coming from icemaker but refrigerator was making ice just fine. had puddle on floor just below freezer door. upon closer inspection realized leak was coming from drain line. there were 2 pieces of tubing and the connector. leak was coming from where tubing goes into connector. wanted to replace it. didn't know what it was called. did live chat with someone I think was named James. he sent me diagrams and I could identify the part. once identified I ordered it. boom.... Read more

$20.95

Compare At:: $25.14
You Save:: $4.19

IN STOCK

Ships Monday Guaranteed

Add to Cart

Best Seller

Genuine Whirlpool part

Admiral Refrigerator Door Gasket

4.5 (13)

By: Whirlpool

Part Number: WP61004010

Color: White. Size: 31 1/2 inches 41 inches. For black order WP61004017.

This part fixes the following symptoms

Door sweating
Fridge runs too long

Do-It-Yourself Stories from Customers like You I needed to replace a refrigerator gasket on my maytag refrigerator: model # mtb2155brw Scott P. • Bucyrus , OH • November 29, 2015

I used the Company's chat line on 11/18/2015 to speak with a representative to make sure I would be ordering the correct replacement part. That was a very helpful and pleasant experience. The agent assured me I would be receiving the part within two days and she was spot on. She indicated I would be receiving an Order Confirmation email with a link to a repair video. The video was very helpful in describing the process to remove the old gasket and the tools I would need. I installed the... Read more

$156.55

Compare At:: $186.29
You Save:: $29.74

IN STOCK

Ships Monday Guaranteed

Add to Cart

Best Seller

Genuine Whirlpool part

Admiral Dispenser Overlay

4.8 (24)

By: Whirlpool

Part Number: WP67004151

The Dispenser Overlay is an OEM part for Whirlpool refrigerators. It is a component that covers and protects the control panel and buttons of the dispenser on the fridge. It provides a protective barrier against dust, moisture, and every day wear and tear, helping to maintain the appearance and functionality of the dispenser.

Causes of a damaged or worn-out dispenser overlay can include regular use over time, accidental spills or scratches, or exposure to harsh cleaning chemicals. These factors can lead to a faded or unreadable display, a sticky or unresponsive touchpad, or an unattractive appearance.

Symptoms of a bad dispenser overlay may include:

Faded or illegible display on the control panel
Unresponsive or sticky buttons on the dispenser
Visible damage, scratches, or discoloration on the overlay

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

Do-It-Yourself Stories from Customers like You The insert and facade of the water & ice dispenser had two broken buttons (bad design) they are intended to break Louis A. • Beaumont , CA • August 23, 2015

1. Purchased a new Facade. The removal of the old one was relatively easy except that the two screws that hold it in place (behind the spill tray) were rusted (they should have used stainless steel ones) one came out with a vise grip but on the other I had to buy an "Easy Out" tool from Home Depot, once out the unit drops down. Had my wife hold the new unit, swiped the wires from old to new, removed the control board from the old one and installed it on the new one with one screw and cleaned... Read more

$55.95

Compare At:: $66.58
You Save:: $10.63

IN STOCK

Ships Monday Guaranteed

Add to Cart

Best Seller

Genuine Whirlpool part

Admiral Air Grille (Top Vent, Microwave)

4.2 (4)

By: Whirlpool

Part Number: WPW10175909

Restore the clean look and proper ventilation of your microwave with this air grille. It covers the upper front vent opening, helps guide airflow through the vent path, and shields internal components for reliable performance.

Covers the upper/front vent opening while allowing proper airflow
Helps secure the charcoal filter on many recirculating models
Restores appearance and fit when the original grille is cracked or missing
Common fix for a loose, rattling, or broken vent cover

What's included: 1 air grille Install notes:

Disconnect power to the microwave before servicing
Open the door (most models), remove the screws along the top edge, and slide the old grille to release its tabs
Position the new grille, ensure tabs engage fully, and reinstall the screws without overtightening

Do-It-Yourself Stories from Customers like You Clogged refrigerator drain; in the process we broke the part we subsequently ordered from you Douglas M. • Phoenix , AZ • September 25, 2016

There is nothing you can't do given the right YouTube video! We disassembled the bottom mount freezer n our Jenn Air refrigerator to remove all the ice and then located the clogged grommet on the back of the unit and cleared it and added a notch. In the process of reassembling we broke the bracket on a part that should have been the easiest portion of the entire installation! In seconds we located and ordered the part on your site. It arrived in a couple of days and then we removed the door and... Read more

$43.95

Compare At:: $52.74
You Save:: $8.79

IN STOCK

Ships Monday Guaranteed

Add to Cart

Best Seller

Genuine Whirlpool part

Admiral Door Gasket (White)

5.0 (2)

By: Whirlpool

Part Number: WP4357099

This white door gasket seals the perimeter of the refrigerator door. It helps keep cold air in and humid air out, supporting stable temperatures and reducing frost and moisture around the door opening. What it does:

Maintains an airtight seal between the door and cabinet
Replaces a torn, cracked, shrunken, or deformed gasket that won't seal
Helps address condensation around the door, frost/ice buildup, temperature fluctuations, or a door that won't close flush

What's included:

1 door gasket (white)

Install notes:

Unplug the appliance before servicing
Warm the new gasket (soak in warm water or use low, indirect heat) to relax kinks for easier fit
Start at the corners and work evenly around the door; on screw-retained liners, loosen screws, seat the gasket lip, then retighten
Close the door and check the seal; smooth out waves and allow the gasket to conform over the next 24 hours

Do-It-Yourself Stories from Customers like You Freezer gasket replaced by 77 year old lady Patricia R. • Florence , OR • July 09, 2017

I purchased a freezer gasket + key// from appliancepartspros.com //easy to order. I did not need to lock up my freezer but thought it might help the gasket seat (good thought). To replace gasket I started at top of door, wow, I should have started at bottom. Hated laying on my "belly" to screw in gasket. Ok, I am 77 years old but got the job done. All went okay until I had to close the door, the door would not stay shut. Key: I locked the door for a week. New seal is settling in, freezer is... Read more

$156.95

Compare At:: $186.77
You Save:: $29.82

IN STOCK

Ships Monday Guaranteed

Add to Cart

Best Seller

Genuine Whirlpool part

Admiral Ice Auger End Cap

5.0 (28)

By: Whirlpool

Part Number: WPD7749401

This end cap fits on the front of the ice-bin auger. It secures the auger shaft and blade stack inside the ice container so cubes or crushed ice dispense smoothly and the auger stays properly aligned.

Secures the front of the auger and blades in the ice bucket
Maintains auger alignment with the drive for reliable ice dispensing
Helps prevent jams and rattling in the ice container
Common symptoms of a failed cap: weak/no ice dispense, loose/wobbly auger, grinding or rattling noises, visible cracks or a missing cap

What's included: 1 end cap Install notes:

Disconnect power and remove the ice bin before servicing
Note the order of blades, spacers, and washers; take a photo for reassembly
Replace the cap and reassemble in the original order using existing hardware
Ensure the bin is fully seated and test dispense after restoring power

This part fixes the following symptoms

Ice maker won't dispense ice

Do-It-Yourself Stories from Customers like You Cap helixend Richard B. • Brevard , NC • March 21, 2015

Removed old cap replace with new 5 min. works like new received new part in 2 days Read more

$26.95

Compare At:: $31.80
You Save:: $4.85

IN STOCK

Ships Monday Guaranteed

Add to Cart

Best Seller

Genuine Whirlpool part

Admiral Door Switch Assembly

4.9 (16)

By: Whirlpool

Part Number: W11291138

The Door Switch Assembly is an OEM replacement part for Whirlpool refrigerators. It is responsible for turning the light on when you open the refrigerator door and turning it off when the door is closed. It ensures that the light functions properly, allowing you to easily locate and retrieve items from your refrigerator.

Symptoms of a faulty door light switch include:

Interior light not turning on when the door is opened
Interior light staying on even when the door is closed

A bad door light switch can occur due to regular use, wear and tear, or accidental damage. If you notice issues such as the interior light not turning on or off when you open or close the door, it may be time to replace the door light switch.

This Whirlpool replacement part is also compatible with Sears/Kenmore models.

Do-It-Yourself Stories from Customers like You Interior light on refrigerator was flashing Billy R. • Reedsport , OR • February 28, 2020

Replaced light switch. That did not work, problem was in led lights. Read more

$27.95

Compare At:: $33.26
You Save:: $5.31

IN STOCK

Ships Monday Guaranteed

Add to Cart

Best Seller

Genuine Whirlpool part

Admiral Door Hinge

4.9 (10)

By: Whirlpool

Part Number: WP8066056

The Door Hinge is an OEM part for Whirlpool dryers. This hinge ensures the secure attachment of the dryer door to the appliance, allowing it to open and close smoothly. Right-hand hinge. For the left hinge use AP3047600

Causes of a bad door hinge can include regular wear and tear, accidental impacts, or overloading the door.

Symptoms of a bad door hinge include:

Door not closing properly
Door sagging or misaligned
Difficulty opening or closing the door
Noises or squeaking when moving the door

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Do-It-Yourself Stories from Customers like You Broken dry door hinge. Lynda S. • Apex , NC • September 24, 2018

Watched your very helpful and informative "how to" video and replaced both right and left hinges. Getting the front panel to line up on the clips was the most difficult part. Read more

$48.95

Compare At:: $58.74
You Save:: $9.79

IN STOCK

Ships Monday Guaranteed

Add to Cart

Best Seller

Genuine Whirlpool part

Admiral Evaporator Fan Motor (Refrigerator)

4.9 (10)

By: Whirlpool

Part Number: WP61004888

This evaporator fan motor circulates cold air across the evaporator coils and through the freezer and fresh-food sections to maintain even temperatures. Replacing a failed or noisy motor restores proper airflow and dependable cooling performance.

Drives the evaporator fan blade to move air over the coils and throughout the cabinet
Helps maintain consistent temperatures between freezer and refrigerator compartments
Failure symptoms include weak/no airflow, the fan not running, loud squealing/rumbling, or the fresh-food section warming up
Poor airflow can also lead to frost or ice buildup on the freezer back panel

What's included: 1 evaporator fan motor Install notes:

Disconnect power before servicing; wear cut-resistant gloves and eye protection
Access the motor behind the freezer's rear panel; use caution around sharp metal and evaporator fins
Note wire positions; transfer the fan blade and any brackets/grommets from the original motor; secure wiring connections
Ensure the blade spins freely; engage the door switch when testing and strong airflow after reassembly

This part fixes the following symptoms

Noisy
Freezer section too warm
Fridge too warm

Do-It-Yourself Stories from Customers like You Evaporator fan motor noisey 15 years old Jack R. • Ithaca , MI • May 19, 2014

Removed back panel in freezer compartment. Held on by four hex head screws. Disconnected wire assembly from panel and then replaced evaporator fan motor on kitchen table. Evaporator fan motor is attached to back side of freezer panel by four hex head screws. Easy repair to do.It took me about 30 minutes to do the repair. Read more

$79.95

Compare At:: $95.14
You Save:: $15.19

IN STOCK

Ships Monday Guaranteed

Add to Cart

Best Seller

Genuine Whirlpool part

Admiral Ice Auger And Crusher Blade Assembly

5.0 (12)

By: Whirlpool

Part Number: WP12740302

The ice auger and crusher blade crush and shave the ice that dispenses on a refrigerator. This part can be used to repair a refrigerator that is no longer dispensing ice. Sometimes when the ice dispenser malfunctions and makes a loud noise but doesn't dispense cubed or shaved ice, the problem is with the auger and crusher blade. Perform a visual inspection of the auger and crusher blade to ensure no external damage is done to the components.Disconnect the refrigerator from its power source before starting this repair. Open the freezer door to access the ice bucket and dispenser area. The bucket is held in place by fastening clips that can be pushed to remove the bucket. Lay the bucket flat on its back with the auger and blade facing upwards. Remove the old auger and crusher blade by removing the four hex screws. Remove the helix end-cap from the old auger system and replace it with the new one. Repeat these steps in reverse to install the new component.This Whirlpool ice auger and crusher is a genuine OEM product sourced directly from Whirlpool. The part listed is only available individually and is not included with any other parts or original appliances. This part is compatible with Whirlpool, Amana, Kenmore, and Maytag appliances.

This part fixes the following symptoms

Ice maker not making ice
Ice maker won't dispense ice

Do-It-Yourself Stories from Customers like You Broken ice bucket and crushed ice agitator George W. • Trophy Club , TX • December 29, 2014

Replaced both parts Read more

$291.66

Compare At:: $347.08
You Save:: $55.42

IN STOCK

Ships Monday Guaranteed

Add to Cart

Best Seller

Genuine Whirlpool part

Admiral Water Inlet Valve (Refrigerator)

5.0 (28)

By: Whirlpool

Part Number: WP61005273

This water inlet valve controls the flow of household water into the refrigerator system. Replacing a failing valve restores reliable water supply for functions like ice making and dispensing.

Opens and closes to allow water into the refrigerator as commanded
Common failure signs: no ice production, slow or no water from dispenser, intermittent fill, or leaks at the valve area
May cause humming from the valve when energized but not filling

What's included: One water inlet valve assembly. Install notes:

Unplug refrigerator and shut off the water supply before starting
Have a towel ready to catch any residual water
Transfer any mounting hardware or fittings from the old valve if reused
After installation, restore water and power, then check all connections for leaks

Do-It-Yourself Stories from Customers like You The ice maker would overflow because the water would not shut off Philip H. • Henderson , NC • June 12, 2014

I replaced the old water valve with the one ordered and the problem was resolved. Read more

$54.95

Compare At:: $65.39
You Save:: $10.44

IN STOCK

Ships Monday Guaranteed

Add to Cart

Best Seller

Genuine Whirlpool part

Admiral Defrost Heater (Evaporator)

5.0 (9)

By: Whirlpool

Part Number: WP67001794

This evaporator defrost heater melts frost from the freezer's evaporator coil during the automatic defrost cycle, restoring proper airflow and cooling. Replacing a failed heater helps prevent recurring ice buildup and temperature swings.

Heats the evaporator coil at set intervals to clear ice
Maintains airflow so the fresh food section and freezer cool consistently
Common signs of failure: heavy frost on the back freezer panel or evaporator
Other symptoms may include warm refrigerator temperatures, reduced airflow, or fan noise from ice contact

What's included: One defrost heater Install notes:

Disconnect power before servicing; wear appropriate PPE
Access the heater behind the freezer's rear panel; defrost ice with warm air/steam—avoid sharp tools
Reinstall in the original position; keep wiring clear of the fan and moving/hot parts; ensure secure harness connections
After reassembly, verify the defrost cycle per service instructions; if frost returns, also check the defrost thermostat/bi-metal and control

Do-It-Yourself Stories from Customers like You Refrigerator warm freezer normal Edward H. • Harrisburg , PA • March 15, 2015

The cooling coils were iced-up. The ice was blocking air flow to the refrigerator. This resulted in the freezer working fine while the refrigerator was warm. Called AppliancePartsPros and talked to Sally. Sally was a big help in troubleshooting the problem. I ordered and replaced the cooling coil heater. If you attempt to do this repair yourself, BE CAREFUL, the cooling coil fins are sharp. Read more

$89.95

Compare At:: $107.94
You Save:: $17.99

IN STOCK

Ships Monday Guaranteed

Add to Cart

Appliance

Appliance

Lawn & Garden

Need help finding dishwasher parts?

Need help finding dishwasher parts?

Need help finding dishwasher parts?

Admiral Refrigerator Parts

Admiral Water Valve Single

Admiral Defrost Thermostat (Refrigerator)

Admiral Crisper Frame Support

Admiral Light Bulb

Admiral Water Line Union

Admiral Refrigerator Door Gasket

Admiral Dispenser Overlay

Admiral Air Grille (Top Vent, Microwave)

Admiral Door Gasket (White)

Admiral Ice Auger End Cap

Admiral Door Switch Assembly

Admiral Door Hinge

Admiral Evaporator Fan Motor (Refrigerator)

Admiral Ice Auger And Crusher Blade Assembly

Admiral Water Inlet Valve (Refrigerator)

Admiral Defrost Heater (Evaporator)

Related Parts

Common Problems

Popular Admiral Refrigerator Models