Amana Dryer Parts

The rubber foot is an OEM replacement part for Whirlpool washing machines. This small but essential component fits beneath the leveling legs, providing stability and preventing the appliance from moving or vibrating excessively during operation. It also protects flooring surfaces from potential scratches or damage.

Symptoms of a bad Leveling Leg Pad include:

• Increased vibration or noise during the wash or spin cycle
• The washing machine wobbling or becoming unsteady
• Visible wear, cracks, or damage to the pad

Causes of a failing Leveling Leg Pad can include wear and tear from prolonged use, exposure to moisture, or excessive weight causing deformation. Replacing worn pads helps maintain the appliance's balance and efficiency.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

For the leveling leg order W10176519.

Leg, adjustable (w/nut)

This hinge cover is a small trim piece that conceals the door hinge and mounting screws. Replace a cracked or missing cover to restore a clean, finished look and help keep lint and debris out of the hinge cavity.

• Covers and protects the door hinge and screw heads
• Restores a smooth, finished appearance around the hinge opening
• Helps shield the hinge pocket from lint and debris
• Common replacement when the original cover is cracked, missing, or loose

• Disconnect power; for gas units, also shut off the gas supply
• Support the door; loosen/remove hinge screws as needed to access the cover
• Remove the damaged cover; position the new cover and secure per model design
• Verify door closes and aligns properly before returning to service

The Door Strike is an OEM replacement part for Whirlpool dryers. This component ensures the dryer door securely latches, enabling the appliance to operate and preventing it from running with the door ajar. It works in conjunction with the door catch to maintain a proper seal during drying cycles.

Symptoms of a bad Door Strike include:

• The dryer door not latching or staying closed
• The dryer not starting due to the door remaining open
• The door popping open during operation
• Visible wear, bending, or damage to the strike

Causes of a failing Door Strike can include regular wear and tear, misalignment from improper use, or damage from slamming the door. Replacing a faulty strike ensures the dryer operates safely and efficiently.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This white handle mounts to your appliance and provides a secure, comfortable grip for everyday use. Replace a cracked or loose handle to restore smooth operation and bring back a clean, factory look. What it does:

• Attaches to the door or drawer front and serves as the pull point for opening and closing
• Helps resolve issues like a cracked/broken or wobbly/missing handle
• Improves ease of use when the handle no longer secures properly
• Refreshes worn or discolored exterior appearance with a matching OEM-style finish

• One handle in white

• Disconnect power to the appliance before servicing; turn off gas if applicable
• Access and remove the fasteners securing the old handle, noting their location/orientation
• Align the new handle; transfer and reuse existing screws, spacers, or end caps as required by your model
• Start all fasteners by hand, tighten evenly, and verify secure fit and smooth operation

This flexible, narrow brush reaches under and behind the cabinet to sweep dust and lint from condenser coils and vents. Cleaning built-up debris helps restore airflow and support proper cooling performance.

• Sweeps dust, lint, and pet hair from condenser coils and ventilation areas
• Flexible reach helps access coils beneath or behind the appliance
• Aids proper heat dissipation by clearing airflow paths
• Helpful when coils are visibly dirty, cooling seems weak, or the unit runs longer than usual

• Unplug or disconnect power before cleaning
• Remove the toe grille or rear access panel if needed to access coils
• Brush gently along the coil fins; avoid bending fins or damaging tubing
• Vacuum or wipe up loosened debris before replacing any panels and restoring power

Door hinge, left. For right hand hinge order WP3387560.

Right hand side. Used most Admiral, Crosley, Norge, and Magic Chef dryers. Includes glide and felt pad.

This door seal replaces a worn or damaged gasket around the oven door, creating a tight barrier between the door and the front frame. A fresh seal helps the appliance heat efficiently and maintain steady cooking temperatures. What it does:

• Seals the gap between the door and oven frame to minimize heat loss
• Helps the oven preheat faster and hold set temperatures more consistently
• Replace if the gasket is torn, brittle, flattened, or frayed
• Common signs include heat escaping around the door edge and longer cook times

• 1 door seal

• Disconnect power and allow the oven to cool completely before beginning
• Open the door and carefully remove the old seal, noting its routing and attachment points
• Clean the mating surface to remove debris for a proper seal
• Install the new seal evenly without stretching; ensure all ends and anchors are fully seated

This dryer power cord connects an electric dryer to a 4-prong household outlet. Replace a worn or damaged cord to restore a safe, reliable power connection and help prevent intermittent power or overheating at the cord connection. What it does:

• Connects an electric dryer to a 4-prong receptacle for proper power and grounding
• Four-conductor design supports modern installation requirements
• Replaces cords with cracked insulation, loose prongs, or burned terminals

• 1 dryer power cord

• Disconnect power at the breaker before servicing
• Attach to the dryer terminal block per the appliance's wiring diagram and secure the strain relief

This replacement control knob restores smooth, reliable turning on your appliance's control panel so you can select settings accurately again. It's designed to slide onto the control shaft and provide a secure, easy-grip interface. What it does

• Attaches to the control shaft to let you select settings
• Replaces cracked, stripped, or missing knobs
• Helps ensure the switch or valve engages properly when turned
• Improves grip and appearance on the front panel

• 1 control knob

• Disconnect power; if servicing a gas appliance, also shut off the gas supply
• Pull the old knob straight off the shaft—do not pry against the panel
• Align the new knob with the shaft flats/splines and press straight on without forcing
• Test operation to ensure the knob fully engages the control

Bottle with brush. Color: Black. Size: 0.6 fl.oz.

The Bulb-Light is an OEM part for Whirlpool refrigerators. It provides lighting within the refrigerator compartments, allowing for easy viewing of contents. The bulb-light joins with compatible sockets or bases designed precisely for its installation within the refrigerator. 

Causes of a bad bulb light can include burnout over extended use, accidental damage during cleaning, or faulty wiring that prevents the bulb from receiving power.

Symptoms of a bad Bulb-Light include:

• Dark or no light in refrigerator compartments  
• Bulb producing a flickering or intermittent light instead of consistent illumination
• Signs of overheating, melting, or charring around the bulb

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This cycling thermostat regulates on/off heat cycles to maintain consistent operating temperature. Replacing a failed thermostat restores proper temperature control and helps protect the appliance from overheating or underheating during normal operation.

• Senses internal temperature and opens/closes contacts to control the heating circuit
• Helps prevent overheating; supports stable, repeatable heat cycling
• Common failure symptoms include no heat, overheating/shutting off too soon, or longer-than-normal run times
• Electrical component—failure may be intermittent before complete loss of function

• Disconnect power (and gas supply, if applicable) before service
• Note wire locations; transfer connectors one at a time to the new thermostat
• Mount firmly against the mating surface for accurate temperature sensing
• After installation, verify proper operation and temperature cycling

The door seal forms the primary gasket around the door opening on horizontal-axis machines, creating a tight barrier that keeps contents contained and prevents gaps that can lead to leaks, odors, and poor performance. What it does

• Seals the perimeter of the door opening to contain wash water and suds
• Helps the door close flush and maintain a consistent, leak-free seal
• Common symptoms: water leaking at the door area, visible tears or cracks in the seal, persistent mildew/odors around the gasket, or a door that won't seal properly

• 1 door seal

• Disconnect power and shut off water supply before servicing
• Remove the front panel/retaining bands as needed to access the seal
• Note orientation and drain holes at the bottom; press the seal fully into its groove all the way around
• Reinstall retainers, ensure the door closes flush, and run a short test to check for leaks

Includes 2 adhesive pads, 2 brackets, 4 screws, and installation instructions.