Amana Spring Parts

The Suspension Spring Kit is an OEM replacement part for Whirlpool washing machines. It contains suspension springs that absorb vibrations and support the weight and movement of internal components like the tub, agitator, and transmission.

Causes of a bad spring kit include wear from years of use, dry rot of rubber components, or damage/breakage incident to an out of balance or overly aggressive load.

Symptoms include:

• Excessive shaking and vibration, especially on higher speed cycles
• Loud banging or knocking noises
• Stress fractures developing in other housing parts over time

This OEM Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

For the complete ice door kit order W10823377.

This ice door spring restores the closing tension on the dispenser chute door. Replacing a fatigued spring helps the flap seal properly after dispensing, reducing warm-air leaks that cause frost buildup and ice clumping around the chute. What it does:

• Provides return tension so the ice chute door closes after dispensing
• Helps maintain a tight seal to limit frost, condensation, and air leaks
• Can resolve a chute door that sticks open/closed or won't fully close
• Reduce rattling or poor ice flow caused by a loose flapper

• 1 spring

• Disconnect power to the refrigerator before servicing
• Remove dispenser trim/control panel to access the ice door assembly
• Note spring orientation on the flapper; transfer/install carefully without over-bending
• Smooth flap movement and a proper seal before reassembly

• Dispenser door spring
• Flapper spring
• Ice chute door spring

This door spring counterbalances your dishwasher door so it opens and closes smoothly without slamming. Replacing a fatigued or broken spring restores proper tension and helps protect the hinges and latch.

• Provides counterbalance tension to the door through the hinge mechanism
• Helps the door open and close with controlled movement and stay in position
• Symptoms of failure can include a door that drops quickly, feels heavy, or won't stay put
• May also cause popping/squeaking noises or uneven action on one side of the door

• Disconnect electrical power and turn off the water supply before servicing
• Remove the toe panel/kick plate to access springs near the hinges
• Carefully relieve and reattach spring tension; wear gloves and eye protection
• Ensure both sides are tensioned evenly after replacement

A replacement tension spring designed to restore proper movement and return force to the appliance mechanism. Helps the affected component operate smoothly so doors, levers or assemblies move with correct tension and alignment. What it does:

• Provides return and holding tension for the appliance mechanism to restore normal movement.
• Helps reduce sagging, misalignment, or loose operation of the associated door or linkage.
• Minimizes noise and vibration caused by a worn or weakened spring.
• Works as the direct-fit part when the listed part number matches your appliance.

• Disconnect power and water (if applicable) before beginning any repair.
• Springs are often under tension—wear eye protection and use caution when removing or installing.
• Follow the appliance's service manual or OEM instructions for correct orientation and safe installation.

This is the idler tension spring that holds the dryer belt tight for smooth drum rotation and reliable drying. It restores proper belt tension to help eliminate slipping and uneven drum movement. What it does:

• Applies tension to the dryer idler assembly so the belt stays engaged with the drum and motor pulley
• Helps stop belt slippage that can cause the drum to not turn or to turn intermittently
• Reduces squealing or rubbing noises caused by a loose or worn tension spring
• Works with the idler pulley and belt to maintain consistent drum rotation during operation

• 1 idler tension spring

• Disconnect power to the appliance before any service to prevent shock or injury
• Access may require removing the dryer front or top; follow OEM service instructions for your model
• Relieve belt tension carefully when removing/installing the spring; use gloves and eye protection
• After installation, verify proper belt alignment and test a short cycle to confirm normal operation

This spring element support secures and stabilizes a range or oven heating element to keep it properly positioned for consistent heating and safe operation. It replaces a worn or broken support that allows an element to sag or vibrate. What it does:

• Holds the bake/broil heating element in the correct position so it heats evenly
• Prevents the element from sagging, touching the oven cavity, or rattling during use
• Helps maintain correct element clearance to reduce arcing and uneven cooking
• Addresses symptoms like a loose or wobbly element, unusual noises, or intermittent heating

• One spring element support

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Handle the heating element and support carefully to avoid bending or damaging the element
• Verify correct part orientation against the oven's wiring diagram during installation

This spring provides tension for the door hinge, helping the door open and close smoothly and stay properly balanced. Replacing a weakened or broken spring restores correct door movement and prevents slamming or drooping.

• Maintains tension on the door hinge mechanism
• Helps the door stay level and close securely
• Can reduce issues like a sagging, loose, or slamming door
• Restores smooth, controlled door operation

• Disconnect power and shut off gas or water (as applicable) before service
• Support the door to relieve hinge tension prior to removal
• Note spring orientation/routing before replacing
• Wear cut-resistant gloves; hinge areas can be sharp and under tension

This idler spring maintains proper tension on the dryer drum belt by keeping the idler pulley engaged. Replacing a weak or broken spring restores consistent drum rotation and helps prevent belt slippage and squealing during operation.

• Maintains belt tension by pulling the idler arm/pulley against the drum belt
• Helps the motor start and keep the drum turning smoothly
• Reduces belt slippage that can cause squealing or chirping
• Common symptoms of a failed spring: drum won't turn or turns intermittently; belt comes off or feels loose; loud squeal from idler area

• Disconnect power; for gas dryers, shut off the gas supply
• Access the idler assembly; relieve belt tension and note belt/spring routing before removal
• Attach the new spring to the same holes/orientation on the idler arm and base; verify belt path
• Rotate the drum by hand to confirm alignment and tension before reassembly

This spring provides the tension or return force used in the appliance's moving assemblies to restore position and maintain secure connections. It's a simple replacement that helps restore proper function and reduce slippage or sag. What it does:

• Replaces a worn or broken tension coil that provides return force for door, latch, or linkage components.
• Helps stop doors, latches, or moving parts from staying loose, drooping, or failing to return.
• Can reduce rattling or clunking caused by a failed spring under load.
• Often used where a compact coil spring is required to maintain tension in a mechanism.

• One replacement spring.

• Disconnect power (and gas if applicable) before servicing—always follow the appliance's safety instructions.
• Use proper tools and keep hands/loose clothing clear of pinch points; springs can release stored energy.
• Verify the exact spring orientation and attachment points before removing the old part.

A replacement solenoid spring that restores proper plunger return and tension for compatible Whirlpool solenoid assemblies. Replaces worn or broken springs to help ensure reliable actuator movement and consistent operation. What it does

• Provides return tension for the solenoid plunger so the actuator snaps back after activation
• Helps restore normal solenoid movement when a worn spring causes sticking or weak response
• Commonly used when the appliance fails to engage, release, or cycle components driven by a solenoid
• Works as a direct-fit spring for the matching solenoid assembly when part is specified

• Disconnect power to the appliance before beginning any repair to avoid shock or injury.
• Remove access panels and the solenoid assembly to access the spring.
• Handle small parts carefully; note placement and orientation of the spring for correct reassembly.
• If other solenoid or actuator components are damaged or corroded, replace the entire assembly for reliable operation.