Bosch Parts

This is a white on/off pushbutton that restores the user control for turning the appliance on and off. It replaces a worn, cracked, or missing button to make the control panel usable again. What it does:

• Acts as the primary on/off actuator on the appliance control panel
• Allows reliable on/off switching when pressed
• Replaces cracked, chipped, or non-responsive buttons
• Helps resolve symptoms like a loose, stuck, or missing on/off button

• One white on/off pushbutton

• Disconnect power to the appliance before attempting any service
• This button typically snaps into the control panel; use gentle prying to remove the old button
• Inspect the control panel bezel and switch mechanism for damage before installing

This sump collects and channels dishwasher wash water into the wash pump, helping maintain proper drainage and reduce leaks at the tub-to-pump connection. Replace a cracked or damaged sump to restore correct water flow and sealing. What it does

• Directs wash water from the tub into the wash pump and drain system.
• Houses the pump inlet and seals the pump-to-tub interface.
• Prevents leaks by providing a secure seal between the tub and pump assembly.
• Common symptoms: pooling water in the tub, dishwasher not draining, leaks from the base, or unusual pump noise/vibration.

• Disconnect power and turn off the water supply before starting any repair.
• Handle carefully; inspect and replace any worn gaskets or seals when installing the new sump.
• Access typically requires removing lower access panels and the lower dish rack.
• After installation, test for leaks and proper drain operation before returning the appliance to normal use.

This is the right side hinge plate. For left side use 00298567.

This gas burner jet holder assembly routes fuel through the orifice to the burner and secures the connection. The red 11,000 BTU version is designated for the right-front or left-rear burner, helping restore proper flame and heat output.

• Positions the jet and routes gas from the manifold to the burner for the specified heat output
• 11,000 BTU, red-coded variant designated for RF/LR burner location
• Provides a stable, serviceable connection between tubing and burner base for a consistent flame
• Symptoms include weak or irregular flame, failure to ignite, or incorrect flame size at the RF/LR burner

• Shut off gas supply and power; allow the appliance to cool before servicing
• Remove grates, burner caps/heads, and any panels needed to access the holder
• Support gas tubing and use two wrenches on fittings to avoid twisting or damage during removal/installation
• After installation, check all joints with an approved leak-detecting solution and verify flame quality

Replacement fan motor that powers the appliance's blower to circulate air for proper cooling and ventilation. Restores airflow and helps reduce noisy operation, overheating, or poor circulation caused by a failed motor. What it does:

• Drives the blower wheel to move air through the appliance, addressing weak or no airflow.
• Stops or reduces unusual grinding, rattling, or humming noises when the original motor fails.
• Restores proper ventilation to help prevent overheating and maintain consistent temperature.
• Used as the specified replacement when this part number is required.

• Disconnect power to the appliance before servicing; for gas models, shut off the gas supply as well.
• Handle wiring connectors carefully and match connector positions/colors during reassembly.
• Basic hand tools are typically required.

This replacement drum belt wraps around the dryer drum and motor pulley to rotate the drum for normal drying. Replaces worn or broken belts to restore tumbling and help your dryer move loads evenly. What it does:

• Transfers motor power to the drum so clothing tumbles during the drying cycle
• Commonly used when the drum slips, won't turn, or makes a rubbing/squealing noise
• Helps maintain proper drum alignment and smooth rotation when in good condition

• Disconnect power before any service; follow the dryer's service manual for safe access
• Inspect idler pulley and motor shaft for wear when replacing the belt
• Re-tension and route the belt per the OEM diagram to avoid mis-tracking

This water inlet hose gasket seals the connection between the supply hose and the appliance's inlet fitting. Replace a flattened or damaged washer to stop drips at the coupling and restore a reliable, watertight connection.

• Creates a watertight seal at the inlet hose-to-appliance connection
• Helps prevent drips, puddles, and water damage around the machine
• Replace if the old gasket is cracked, hardened, flattened, or missing
• Common symptoms: leaking at the hose coupling or needing to retighten the fitting to stop drips

• Disconnect power and turn off the water supply before servicing
• Place a towel to catch residual water, then detach the inlet hose from the appliance fitting
• Remove the old gasket from the hose coupling and seat the new gasket evenly
• Reattach and hand-tighten the coupling; open water supply and check for leaks—do not overtighten

This burner base supports the cooktop burner assembly and helps position the burner cap for a consistent flame. Replace a damaged or warped base to restore proper burner alignment and reliable ignition. What it does

• Holds the burner head and cap in the correct position for even flame distribution.
• Stabilizes the burner assembly so the ignition electrode can spark reliably.
• Helps prevent burner cap wobble or misalignment that causes uneven heating.
• Can resolve symptoms like burners that light intermittently or produce an irregular flame pattern.

• One burner base.

• Disconnect power and shut off the gas supply before beginning service.
• Remove burner grates and caps; replace base using basic hand tools—do not force parts.
• Inspect surrounding gaskets and the ignition electrode for damage; clean any debris before reassembly.

This rear pump housing is the dishwasher's molded enclosure that supports the drain/pump assembly and channels wash and drain water. Replacing a damaged housing restores proper water flow and helps stop leaks. What it does:

• Houses and aligns the drain/pump components and motor coupling
• Channels water between sump, pump and drain lines to ensure proper draining
• Prevents leaks by sealing the pump assembly area when intact
• Can cause noisy pump operation or failure to drain if cracked or broken

• One rear pump housing

• Disconnect power and turn off water supply before starting; drain any standing water
• Inspect associated seals, gaskets, impeller and mounting hardware; replace if worn
• Handle carefully to avoid damaging mating surfaces; test for leaks after reassembly

Replacement knob for the cooking area that restores reliable control over cooktop burner settings. Replaces cracked, stripped, or missing knobs so you can safely select and adjust heat levels. What it does

• Turns the cooktop control shaft to set burner heat (off through high) and restores tactile control.
• Replaces knobs that are cracked, melted, stripped, loose, or missing.
• Maintains proper alignment and grip for accurate temperature selection.
• Helps prevent accidental control movement from worn or damaged knobs.

• Always ensure controls are OFF and the surface is cool before removing or installing the knob.
• Pull the old knob straight off the control shaft; align and push the new knob onto the shaft until it seats.
• No special tools are typically required; if a knob is stuck, protect the finish and use gentle leverage.

Drum shock absorber for front-load washers. This damper connects the tub to the chassis and controls movement during wash and spin, reducing vibration and noise so the washer can ramp to proper spin speed without banging.

• Damps and stabilizes the drum to control vibration during acceleration, spin, and coast-down
• Helps reduce shaking, banging, and "walking" across the floor
• Can help address out-of-balance messages and noisy operation
• Worn shocks may leave loads wet after spin or cause loud thumping

• Disconnect power and shut off water before servicing; move the appliance to access panels safely
• Access the shock from the front or rear per model; support the tub to relieve tension
• Note pin/bolt orientation; transfer any reusable hardware and fully seat both ends of the new shock
• Consider replacing them as a set for balanced damping; run a short test cycle to verify stability

This jet holder assembly secures the burner orifice and delivers the correct-sized gas jet for a 12,500 BTU natural gas burner, helping restore proper flame size and consistent ignition. What it does:

• Holds the burner orifice in the correct position so gas flows through the proper jet
• Provides the factory-sized orifice for a 12,500 BTU natural gas burner to maintain intended flame height
• Helps correct weak or uneven flames caused by a missing, damaged, or incorrect jet holder
• Supports reliable ignition when installed and aligned properly

• One jet holder assembly (blue) with the 12,500 BTU natural gas orifice installed

• Turn off the appliance and shut off the gas supply before starting any work
• Only install the exact orifice variant specified for your appliance; confirm color/marking and orientation before tightening
• Re-check all gas fittings and perform a leak test after installation

Bushing included. To order bushing separately use 00165296. This is the left side hinge. For right side hinge use 00263119.

Replacement oven door handle that restores a secure grip for opening and closing the oven door. Replaces cracked, broken or loose handles to help make daily use safer and more reliable. What it does:

• Provides a firm grip to open and close the oven door smoothly.
• Replaces handles that are cracked, broken, loose, or missing.
• Helps prevent further damage to door trim and reduces the risk of sudden handle failure.
• Designed for factory mounting locations for a straightforward swap.

• Disconnect power to the appliance before starting; for gas units, turn off the gas supply if applicable.
• Support the door while removing and installing the handle to prevent the door from dropping — use a helper if needed.
• Remove existing mounting screws or fasteners, position the replacement handle, then reinstall and snug hardware.

This outer door is the dishwasher's exterior front panel that restores the appliance's appearance and protects internal components from damage. It provides a finished look and replaces dented, scratched, or corroded panels. What it does

• Covers and protects the inner door assembly, controls, and insulation from impact and moisture.
• Restores the dishwasher's exterior finish and alignment for proper sealing.
• Helps prevent further cosmetic damage and exposure-related corrosion.
• Resolves issues where visible dents, deep scratches, or rust affect the door surface.

• One outer door panel only.

• Disconnect power and water supply before starting any repair.
• Door panels can be heavy or awkward—have a second person assist to avoid dropping or bending the panel.
• Follow the manufacturer's service manual for correct removal/reinstallation steps and torque specifications.
• If trim, latch, or control components are attached, verify whether they must be transferred from the old door.

This washing machine shock absorber stabilizes the outer tub during wash and spin. Replacing a weakened damper helps control vibration and noise so the washer runs smoother and is less likely to shake, bang, or walk.

• Mounts between the tub assembly and cabinet/base to cushion movement
• Helps prevent excessive vibration, shaking, and thumping noises
• Can reduce "walking" or out-of-balance interruptions when a damper is worn
• Supports smoother, quieter spin performance

• Disconnect power and turn off water supply before servicing
• Remove the appropriate access panel(s) to reach the dampers
• Support the tub when removing mounting pins/bolts; match the original orientation
• Inspect all dampers; replace any that show wear for balanced performance