Bosch Parts

Fix a dishwasher that runs endlessly without heating water. This heating element restores proper water temperature for effective cleaning cycles.

Flexible rubber seal between washer tub and door opening. Replace if you notice leaks, tears, mold, or water dripping during cycles. Confirm fit with model.

Removes chlorine and impurities for better-tasting coffee. Replace after approximately 400 cups of coffee or 1000 espresso shots. Verify fit with your model.

Fix a washer that won't stop filling or overflows during cycles. This water valve magnet controls water flow during wash and rinse. Common DIY repair.

Replacement fan motor that circulates air to help maintain proper operating temperature and protect components from overheating. Restores airflow to stop noisy operation, vibration, or a fan that won't run. What it does:

• Drives the appliance cooling/evaporator/condenser fan to move air across coils and components.
• Restores proper airflow to improve cooling performance and reduce overheating risk.
• Stops common symptoms like loud humming/grinding, excessive vibration, or a fan that does not spin.
• Helps prevent related issues caused by stalled or weak fans.

• Disconnect power to the appliance before beginning any repair.
• Handle the fan blade and motor shaft carefully to avoid damage; use basic hand tools.

Dishwasher not filling with water or soap not dissolving? The water inlet valve controls water flow into your dishwasher. Takes about 1 hour to replace.

Seals the NTC temperature sensor port in your dishwasher to prevent leaks and ensure accurate temperature readings. Replace if leaking or worn. Verify fit with your model number before ordering.

Replacement foot assembly for gas cooktop or range grates. Installs on the underside to cushion contact and stabilize the grate. Replace when worn, missing, or broken.

Replace a cracked, missing, or sticky control panel button on your dishwasher. This button provides the physical interface to press the underlying switch.

This replacement lid restores the appliance's finished top cover, protecting internal components and helping the door/hatch close properly. Use when the original lid is cracked, warped, or missing to keep the unit looking and operating as intended. What it does:

• Covers and protects the appliance's top/opening area from debris and damage.
• Secures to existing hinge or mounting points to ensure proper closure.
• Replace if you see visible cracks, chips, warping, or if the lid no longer latches or aligns.
• Helps prevent rattling or rubbing caused by a damaged or loose lid.

• Disconnect power (and water, if applicable) before starting any repair.
• Handle edges carefully; some lids include glass or thin sheet material that can chip.
• Basic hand tools (screwdriver/torx) may be required; keep mounting hardware if reusing.

Seals the aqua sensor assembly to prevent water leaks and protect electronics. Replace if you notice leaks or sensor errors. Confirm fit with your model.

Support strap that cushions and secures the dishwasher circulation motor, stabilizing the motor assembly to reduce vibration and help maintain alignment for steadier, quieter operation. Designed for circulation motors with softer bearings. What it does:

• Cushions and supports the circulation motor to limit movement and vibration and reduce motor noise.
• Secures the motor assembly to the tub/chassis to maintain proper clearance and fit.
• Helps prevent undue stress on motor bearings and mounting points that can cause premature wear.
• Commonly replaced when the strap is cracked, stretched, or no longer holds the motor firmly in place.

• Disconnect power and water supply before servicing; follow all safety and OEM service instructions.
• Remove access panels and any obstructing components to reach the circulation motor as required.
• Replace using the original mounting hardware; inspect motor mounts and bearings while accessible.
• Reassemble and run a short test cycle to confirm reduced vibration/noise and proper motor operation.

This is a white on/off pushbutton that restores the user control for turning the appliance on and off. It replaces a worn, cracked, or missing button to make the control panel usable again. What it does:

• Acts as the primary on/off actuator on the appliance control panel
• Allows reliable on/off switching when pressed
• Replaces cracked, chipped, or non-responsive buttons
• Helps resolve symptoms like a loose, stuck, or missing on/off button

• One white on/off pushbutton

• Disconnect power to the appliance before attempting any service
• This button typically snaps into the control panel; use gentle prying to remove the old button
• Inspect the control panel bezel and switch mechanism for damage before installing

Restores tactile control over burner or temperature settings. Replaces cracked, stripped, worn, or missing original knobs for precise heat adjustment.

Dishwasher not spraying water or dishes staying dirty? The circulation pump motor distributes water to spray arms. Moderate DIY repair, about 3 hours.

Dishwasher not draining or water pooling at bottom? A cracked sump disrupts water flow to the pump. This housing restores drainage and prevents leaks.