Parts for Whirlpool KSEG700EBS0: 03 - Chassis Parts

Mounts to the range frame to anchor the door hinge arm. Replace if cracked, bent, or worn to restore proper door alignment and smooth operation.

Replacement mounting screw for ranges. Secures panels, trim pieces, control boards, and brackets. Order when original screws are missing, stripped, or damaged.

Replacement side panel that restores your range's exterior finish. Covers dents, scratches, or damaged cabinet trim. Easy-to-install cosmetic part.

Size: 10-32

Seals oven door to prevent heat loss and maintain consistent temperature. Replace if frayed, flat, or allowing smoke/heat to escape. Clips install easily.

The Broil Element is an OEM part for Whirlpool wall ovens and ranges. This heating element is responsible for the broiling function of the oven.

Located at the top of the oven cavity, the broil element functions by directing intense radiant heat downward to cook and brown food from above. 

Causes may include natural wear and damage over prolonged high-heat use. Electrical malfunctions inside the element can also cause premature failure. 

Symptoms of a bad broil element include:

• Failure of the broil function
• Diminished or uneven heating during broil cycles
• The presence of cracks, breaks or corrosion on the heating coils

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Bake Element is an OEM replacement part for Whirlpool ovens. It is a component responsible for generating the heat necessary for baking and roasting operations within the oven cavity.

Symptoms of needing to replace the bake element include:

• Uneven or inconsistent baking results
• Difficulty in reaching or maintaining the desired oven temperature
• Visible damage or burnout on the element itself
• Unusual smells or odors associated with a faulty heating element

Causes of a faulty bake element can include normal wear and tear over time, electrical malfunctions, or physical damage due to impact or excessive temperature fluctuations.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore oven models.

This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.

• Fastens panels, brackets, covers, or internal parts to the chassis or frame
• Helps maintain alignment and support, reducing rattle, vibration, or looseness
• Replaces missing or damaged screws that have backed out, broken, or stripped
• Restores secure mounting after service when original hardware is lost

• Disconnect power; shut off water or gas supplies before servicing
• Use the correct driver; start threads by hand to avoid cross-threading
• Match length and thread to the original location; do not substitute with longer hardware
• Tighten snugly; do not overtighten into plastic or thin metal

Front leveling foot adjusts range height for stability. Replaces cracked, broken, or missing feet. Ensures proper leveling to reduce vibration.

This factory screw secures panels, brackets, or trim within your appliance. Replacing a missing or stripped fastener restores a tight fit, reduces vibration and rattles, and helps keep components aligned for reliable, long-term performance.

• Fastens panels, brackets, or trim to the appliance cabinet/frame
• Replaces damaged, rusted, or missing hardware
• Helps eliminate vibration noises, gaps, and loose-fitting parts
• Supports proper alignment of adjoining components

• Disconnect power; turn off gas/water supplies where applicable.
• Match to the original screw from your model's parts diagram before installation.
• Start threads by hand to avoid cross-threading; use the correct driver bit for the head.
• Tighten snugly—do not overtighten to prevent stripping threads or cracking plastic bosses.

Protects oven cavity components from direct heat and maintains temperature distribution. Replace if damaged, warped, or missing to prevent heat wear.

Structural support base for range drawer rail assembly. Replacement needed when original is cracked, broken, or warped causing misalignment or instability.

Structural support base for range drawer rail assembly. Replacement needed when original is cracked, broken, or warped causing misalignment or instability.

Adjustable leveling leg installs on the front or rear corners of your range. Replace if broken, cracked, or worn to stabilize and level your appliance.

Oven won't heat or both elements stopped working? A faulty thermal fuse cuts power to prevent overheating. Easy DIY fix with basic tools in under an hour.

Replacement mounting screw for securing appliance panels, trim, and internal components. Restores proper fastening when original screws are missing or stripped.

Service bracket for electric and gas ranges. Mounts internal components securely. Replace if bent, broken, or missing to restore proper structural support.

The Terminal Block is an OEM part for Whirlpool ranges. It serves as a crucial connection point for the range’s electrical wiring, ensuring a safe and reliable transfer of power to the appliance.

Over time, terminal blocks can deteriorate due to factors such as heat exposure, electrical surges, or wear and tear. When the terminal block becomes damaged or corroded, it can lead to poor electrical connections or potential safety hazards.

Symptoms of a bad terminal block include:

• Burnt or scorched connections
• Intermittent power loss to the range
• Difficulty in the range heating up properly
• Visible damage or corrosion on the terminal block

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.

• Fastens panels, brackets, covers, or internal parts to the chassis or frame
• Helps maintain alignment and support, reducing rattle, vibration, or looseness
• Replaces missing or damaged screws that have backed out, broken, or stripped
• Restores secure mounting after service when original hardware is lost

• Disconnect power; shut off water or gas supplies before servicing
• Use the correct driver; start threads by hand to avoid cross-threading
• Match length and thread to the original location; do not substitute with longer hardware
• Tighten snugly; do not overtighten into plastic or thin metal

Light socket assembly houses your oven bulb and provides electrical connections to illuminate the interior. Replace when bulb won't stay secure or light fails.

Original Whirlpool light bulb, 40 watt.

Symptoms of needing to replace the light bulb include:

• Dimming or flickering light
• Complete lack of illumination inside the appliance
• Visible signs of damage or burnout on the bulb itself

Causes of a faulty light bulb can include normal burnout over time, electrical issues, or physical damage due to impact or vibrations.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Kenmore, Frigidaire, GE, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore appliances.

Self-tapping screw secures panels, brackets, and trim to range frames and housings. Replace worn, missing, or stripped fasteners to restore fit.

Oven not heating to correct temperature or overheating? The temperature sensor monitors and maintains accurate oven temps. DIY repair in 30 minutes.

This replacement screw secures appliance panels and components so they stay tight and aligned during use. Replacing a missing or damaged screw restores a solid fit and helps eliminate rattles, loose trim, or shifting parts.

• Fastens brackets, panels, trim, or components to the appliance chassis
• Helps correct loose or missing hardware after vibration or service
• Replaces stripped, rusted, or broken screws
• Can reduce rattling noises or misaligned parts caused by missing fasteners

• Disconnect power; for gas appliances, also shut off the gas supply
• Support the part being fastened; start threads by hand to avoid cross-threading
• Use the correct driver size; tighten snugly without overtightening
• Replace hardware with the exact part number to ensure proper fit

Protects range wiring from heat, abrasion, and vibration damage. Replace when insulation is cracked, frayed, or exposed. Verify fit with your model number.

The Screw is an OEM part for Whirlpool ranges. This screw is used to secure various components within the range, ensuring that parts such as panels, control boards, or burners are firmly attached and remain stable during operation.  

Causes of a bad range screw can include regular wear and tear, over-tightening, or exposure to high heat.  

Symptoms of a bad range screw include:

• Loose or unstable components within the range
• Difficulty in securing parts during maintenance or repair
• Visible damage or wear on the screw
• Parts becoming misaligned or rattling during operation

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Replacement mounting spacer for ranges. Maintains proper alignment and clearance between components. Replace if missing, cracked, or worn to restore spacing.

Protective panel lining the bottom of your oven cavity. Replace if cracked, warped, or rusted from heat exposure and spills. Provides smooth surface.

Oven light not turning on when door opens? This door-activated switch detects door position and controls interior lighting. Easy push-in installation.

Fix loose or burnt wire connections in your range with this wire connector. Essential for restoring power to burners or oven elements. Simple repair.

Adjustable oven rack shelf for electric and gas ranges. Replaces worn, warped, or missing racks to restore proper cookware support and oven airflow.

The Convection Fan is an OEM part for Whirlpool wall ovens and ranges. It circulates hot air inside the oven cavity, facilitating even heat distribution during the cooking and baking cycles. The convection fan enhances cooking performance through fast, forced air movement.

Causes of a bad convection fan include a failed motor, worn-out blades, or blockages that disrupt airflow.  

Symptoms of a bad convection fan include:

• Incomplete or uneven cooking even at higher temperatures
• Longer than normal cook times 
• Loud buzzing or grinding noises from the fan motor area

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Support bracket for ranges. Provides structural support for internal components. Replace if cracked, bent, broken, or missing to restore stability.

Oven floor dirty or stained? This hidden floor pan protects the cavity from spills and debris while maintaining heat distribution. Direct fit.

Replace the air duct in your electric or gas range. This component channels airflow through the appliance and may need replacement if cracked or damaged.

The Fan Blower is an OEM replacement part for Whirlpool ranges. This component is crucial for circulating air within the range to ensure even heating and proper ventilation during cooking.

The fan blower can fail due to wear and tear from regular use, buildup of grease and debris, or electrical issues. Overheating or physical damage can also cause the blower to malfunction.

Symptoms of a bad fan blower include:

• Unusual noises or rattling during operation
• Inadequate ventilation or uneven cooking
• The fan not running or starting intermittently
• Overheating of the range

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This door channel secures the range door glass panel. Replace if the original is cracked, broken, or missing to restore proper door assembly and appearance.

Protective cover that shields and organizes range wiring. Replace if your wire harness cover is cracked, broken, or missing to prevent wire damage.

Rear cover panel for electric and gas ranges. Installs on the back of the range to protect internal components. Replace if cracked, damaged, or missing.

Oven steam rack reservoir that holds water for moisture release during cooking. Replace if cracked, leaking, or broken to restore steam function.

Oven steam rack reservoir that holds water for moisture release during cooking. Replace if cracked, leaking, or broken to restore steam function.

Heavy-duty steam oven rack for electric and gas ranges. Replace worn, warped, or damaged racks to restore proper cookware support and stability.

Replace bent, rusted, or missing oven racks to restore a stable cooking surface. This rack slides in and out smoothly for safe baking and roasting.

Insulation panel that lines the oven door to provide thermal protection. Replace if torn, compressed, or missing to restore proper heat retention.

Replace cracked or worn door insulation on your range. This thermal barrier installs between the door panels to improve heat retention and efficiency.

Cable retainer strap for electric and gas ranges. Secures wiring harnesses in place. Replace if cracked, broken, or missing to properly hold cables.

If your oven runs hot or cold or exterior surfaces feel too warm, damaged cavity insulation may be the cause. This thermal barrier restores even heat.