Crosley Dishwasher Parts

Replaced the upper spray arm tube with a new one. Also replaced delivery tube grommet and the delivery tube gasket. Now everything works fine and no more leaks. Read more

• Not drying dishes properly

Turned off power to dishwasher. Removed front bottom cover of dishwasher and removed the wires going to each end of the heating element. unscrewed the two nuts holding the faulty heating element in place. Then removed bottmo dish rack and spinning washer arm from inside the dishwasher. Removed old heating element and replaced with new one. Installed in reverse order (tightened two nuts, connected wires, etc.). Turned power on as last step and was off and running...or should I say washing. Read more

• Noisy

After having replaced the drum support rollers twice in a roughly 3yr period, I realized something wasn't quite right, and indeed it wasn't. I had been ordering the wrong parts - I did use the online parts locator after checking, & double checking my model number. Apparently my older Whirlpool dryer has a somewhat ambiguous model number because the rollers that were shipped each time looked nothing like the originals. I realize that is not particularily uncommon - manufacturers often modify... Read more

I ordered the parts and replaced them with new ones. Read more

Tipped the dishwasher on to its front, loosened the drain hose clamp and pulled the hose off. Then unscrew the fill hose which looks like a garden hose adapter. Cut the zip tie on the drain hose and take note of how both hoses are routed, then pull both hoses out the back of the dishwasher. Insert new hoses and route them correctly and hook everything back up. Couple of notes, I didn't have to take off the outer cabinet to do this repair. Get plenty of towels because a lot of water can get... Read more

Replaced it. Read more

Replaced hose Read more

I first wanted to get the dishwasher running, before ordering the spring links. So I disassembled the pump / motor assembly to determine the reason the motor would not start. My wife cleaned all of the parts in the pump assembly. I took the motor apart and discovered that the lower bearing ( a sleeve type bearing) was dry and dirty, and was the culprit for the motor seizing. I cleaned up the bearing and lubricated it with SAE 20W. I also packed felt inside the cavity adjacent to the bearing.... Read more

The key was that information section that shows what model of dishwasher is compatible it was the only site I could find Read more

We initially noticed the dishwasher running loud and failing to completely clean dishes. Research suggested issues like this were normally caused by either the main circulation motor or the drain motor. Over the next week the noise worsened, and it became obvious that the circulation motor had went (loud whirring noise whenever the spin cycle kicked in). I watched a couple youtube videos on the removal and dissassembly until I felt confident that my wife and I could handle the project. For the... Read more

Dishwasher washer would not drain after hearing glass-like particles during the drain cycle despite trying to clean the cylinder filter. Originally suspected the drain motor was damaged. After watching a video on how to replace the drain pump, I carefully energized the dishwasher (from water and electricity) then removed the dishwasher to take a look. After removal of drain hose from the pump, discovered that drain hose was connected to water inlet assembly which also needed removal to... Read more

The fix took 30 seconds. The key to success was your video that explained how reinstalled parts "lock in". Read more

• Won't start
• Door latch failure

Discovered that the common cause of the problem was the latch in the door. Found a video online that showed the exact procedure for my model dishwasher. Ordered the part from AppliancePartsPros on a Thursday afternoon and it was in my hands by noon on Friday. Carefully took the door apart, compared parts, reassembled, and the joy on my wife's face was priceless when the dishwasher started up without doing anything special. Do not be afraid to attempt this repair. Read more

Replaced hose that came with the new washer with this longer one. Read more

I first thought the leak came from the pump assembly rear o ring. I was wrong. The water was leaking from the pump. The pump assembly was shipped in 1 1/2 days with 2 more o rings. I lubed the o rings with dish soap, they slid in perfectly. reinstalled the clamp and screws and was ready to reinstall the dishwasher. Worked great. Next time I will buy the pump the first time. Buying the o rings separately adds $$. Read more

I first thought the leak came from the pump assembly rear o ring. I was wrong. The water was leaking from the pump. The pump assembly was shipped in 1 1/2 days with 2 more o rings. I lubed the o rings with dish soap, they slid in perfectly. reinstalled the clamp and screws and was ready to reinstall the dishwasher. Worked great. Next time I will buy the pump the first time. Buying the o rings separately adds $$. Read more