Crosley Dishwasher Parts

The Power Cord Kit is an OEM replacement part for Whirlpool dishwashers. It is a 3-prong grounded, 16-gauge cord that includes all the hardware needed for installation. Includes all hardware needed for installation.

Causes of a bad power cord can include normal wear and tear over years of use, accidental impacts or cuts to the wiring, or improper installation that damages components.

Symptoms of a bad power cord include:

• The dishwasher not turning on or completing cycles
• Warm or hot power cords during operation
• Frayed, cracked, or exposed copper wiring

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air, and some Kenmore models.

This replacement seal restores a tight barrier between mating parts in your appliance, helping contain air, moisture, or fluid so the unit operates efficiently and reliably over time.

• Provides a compressible barrier between components to prevent escaping air or liquids
• Helps maintain proper performance when the original seal is worn or deformed
• Common symptoms include poor sealing, seepage around a joint, or visible cracks/flattening
• Replace if cut, brittle, misshapen, or no longer seats securely

• Disconnect power; shut off water or gas supply before servicing
• Note the seal's orientation and seating depth before removal
• Clean mating surfaces and grooves; avoid sharp tools that could damage the new seal
• Seat the new seal evenly all the way around; reassemble and test for a proper seal

Comes with the metal shields

Left hand hinge. For right hinge use WP8066056

This float detects and monitors water levels in the appliance's sump/drain area to help prevent overfilling and water pooling. Replacing a damaged or stuck float restores proper water sensing and reduces leak risk. What it does:

• Senses water level in the drain pan or sump so the appliance can stop or redirect water flow
• Helps prevent water from overflowing or pooling under the appliance
• Can stop false fill/overfill conditions caused by a stuck or broken float
• Fault symptoms include water pooling, continuous or unexplained filling, or failure to drain properly

• Always unplug the appliance before accessing internal panels or service areas
• Remove the required access panels or trim to reach the sump/drain area; follow the model's service manual
• Handle the float and any clips or wiring carefully to avoid damage; reconnect any electrical connectors securely
• After installation, restore power and run a manual fill/drain test to verify proper operation

This water inlet valve regulates the flow of household water into the appliance. When the control energizes the solenoid, it opens to deliver the correct amount of water for filling and operation, restoring proper flow and performance.

• Controls on/off flow from the household water supply
• Opens when signaled to provide the correct amount of water for fill functions
• Helps maintain consistent water flow to the system
• Common failure symptoms: no water flow, slow fill, intermittent filling, or leaking at the valve body

• Disconnect power and turn off the water supply before servicing
• Place a towel to catch residual water and relieve line pressure
• Note tubing and wire locations before removal; transfer any brackets or clips as needed
• After installation, restore water and power, check for leaks, and purge air from the lines

This is the complete lower dishrack that slides in and out on the tub rails. It provides a stable place to load plates, bowls, and larger cookware on the bottom level and restores smooth rolling and proper dish placement when the original rack is worn or damaged.

• Holds and organizes dishes on the lower level of the dishwasher
• Restores smooth rolling and proper alignment of the lower rack
• Common failure signs include broken or rusted tines, wobbling or derailed rack, and difficulty rolling the rack in/out
• Helps when dishes are not staying in place or the rack no longer supports loads properly

• Disconnect power before servicing
• Pull the old rack straight out of the tub; transfer any usable accessories if applicable
• Slide the new rack onto the existing rail tracks; ensure wheels are seated on both sides
• Test smooth movement and clear door closure before running a cycle

The Pump Cover is an OEM part for Frigidaire dishwashers. It is designed to cover and protect the dishwasher's pump, which is essential for the proper circulation of water during the wash cycle. This cover helps ensure that the pump operates efficiently and prevents debris from entering and damaging the pump.

Causes of a bad pump cover can include repeated exposure to high water pressure, accidental impact during loading or unloading of dishes, or buildup of debris and hard water deposits.

Symptoms of a bad Pump Cover include:

• Leaks coming from the pump area
• Unusual noises during the wash cycle
• Decreased washing performance
• Visible cracks or wear on the cover

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Supplies water to the spray arm.

The Sump Cover and Filter is an OEM part for Frigidaire dishwashers. Located inside the bottom of the tub, it seals off and protects the drainage sump where debris collects after each wash cycle. The attached mesh filter screens out particles that could otherwise clog drain lines.

Causes can involve mineral buildup that blocks the filter mesh over time, cracks in the plastic housing exposing the sump, or a missing or damaged filter that fails to trap solids.

Symptoms of a bad sump cover and filter include:

• Standing water inside the bottom of the dishwasher tub
• Reduced drainage or water removal after cycles complete
• Floating debris trapped near the drain pump area

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.
 

Color: Grey. 4oz bottle with brush used for touching up damage to your dishracks. For blue use W10840471. For white use WP676453. For tips use 676458.

This dishwasher water deflector redirects spray back into the tub at the front edge, helping prevent splash-over and leaks during cycles. Replace a cracked, warped, or missing deflector to keep floors dry and wash performance consistent.

• Directs wash water away from the door opening and front corners
• Helps reduce leaks and puddles at the bottom front of the dishwasher
• Restores proper containment when the original deflector is deformed, loose, or missing
• Common symptoms include water on the floor at the front, drips during cycles, or visible damage to the deflector

• Disconnect power and turn off the water supply before servicing
• Open the door to access the front/tub area; remove the old deflector
• Clean the mating area and seat the new deflector fully and evenly
• Run a short test cycle and check for leaks

This float controls your dishwasher's water level. As the tub fills, it rises to signal the float switch to shut off incoming water, helping prevent overfilling and leaks.

• Lifts with the water to actuate the float switch and stop filling
• Helps protect against overfilling and door leaks
• Replace if the float is cracked, deformed, waterlogged, or sticks in its well
• Symptoms can include: won't fill or stops filling early; overfilling or leaks at the door

• Disconnect power and shut off the water supply before servicing
• Remove the lower rack and locate the float in the tub floor
• Lift the old float straight up; clear any debris; seat the new float and free up-and-down movement
• Restore power and run a fill test to proper operation and check for leaks

This heater warms the wash water inside the tub during selected cycles. Replacing a failed element restores proper water temperatures, supporting cleaning performance and preventing extended run times or incomplete cycles. What it does:

• Heats water in the washer tub during hot/sanitize/temperature-controlled cycles
• Helps maintain target temperature for effective cleaning and stain removal
• Common symptoms include water not heating, cycles taking unusually long, or cycles stopping early
• Accompany control errors related to water temperature or the heater circuit

• 1 heater

• Disconnect power and shut off water supplies before servicing
• Access is typically from the rear or bottom; be prepared for residual water when removing the old element
• Clean sealing surfaces and seat the element fully; tighten fasteners evenly to prevent leaks
• After installation, run a hot cycle to check for leaks and heating

The Pressure Switch is an OEM part for Frigidaire dishwashers. It plays a crucial role in monitoring water pressure inside the dishwasher, signaling the control module when to activate various components during the wash and rinse cycles. Overl or under pressure conditions could damage the dishwasher or prevent it from cleaning properly.

Symptoms of a bad pressure switch include: 

• Dishes not getting fully clean 
• Cycles not completing or getting stuck
• Error codes displaying
• Strange noises or leaks coming from the dishwasher

Causes of a bad pressure switch can be wear and tear over time, mineral buildup interfering with the switch's function or accidental damage from household chemicals or objects left in the dishwasher. 

This OEM Frigidaire replacement part is designed to function like the original part for reliable performance. It is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. 
 

This cap secures the dishwasher wash arm to its support, helping keep the arm properly positioned so water jets can spin and spray effectively for consistent cleaning performance.

• Holds the wash arm in place on its hub/support
• Can help address a loose, wobbly, or detached wash arm
• Replacing a damaged or missing cap can restore stable arm rotation

• Disconnect power and turn off water before service
• Remove the lower rack for access; lift off the wash arm
• Unscrew/press off the old cap; seat and secure the new cap
• Ensure the wash arm spins freely by hand before reassembly