Crosley Dishwasher Parts

This is a circulation pump motor for dishwashers. It controls the main pump of the appliance.The pump is directly responsible for removing extra water from the dishwasher after use. When a dishwasher's circulation pump motor goes bad, the main indicator is usually leaking from the appliance. There will be a noticeable amount of water emerging from the bottom of the machine whenever the cycle is engaged. Unplug the dishwasher from its main power source and water hookup. Remove the dishwasher from its space in the counter. Remove all necessary entry plates to access the interior of the dishwasher. There is a metal bracket holding the current motor in. Unscrew the two screws that secure the bracket and remove this component. Remember which way the motor is oriented before removing it. Unplug the power cable connecting the motor to the dishwasher. Put the two new sealing rings on the new pump motor. Repeat these instructions in reverse to install the new part.This Frigidaire dishwasher circulation pump motor is a genuine OEM replacement part sourced directly from Frigidaire. The pump motor is sold individually. This part is compatible with Frigidaire, Kenmore, Westinghouse, and Gibson appliances.

The Dishrack Roller is an OEM part for Frigidaire dishwashers. This part ensures smooth and effortless movement of the dishrack in and out of the dishwasher. These rollers are attached to the sides of the dishrack, ensuring that it can glide easily without sticking or jamming, thus preventing damage to the dishes or the dishwasher itself.  

Causes of a bad Dishrack Roller can include wear and tear from regular use, damage from overloading the dishrack, or degradation of the roller material over time.  

Symptoms of a bad Dishrack Roller include:

• The dishrack sticking or struggling to move in and out
• A noisy operation when pulling the dishrack
• The dishrack tilting or becoming unaligned due to a missing or broken roller

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Wash Arm Bearing is an OEM replacement part for Frigidaire dishwashers. It is a crucial component that supports and facilitates the smooth rotation of the wash arm during the dishwashing cycle. The wash arm is responsible for spraying water and distributing detergent solution evenly throughout the dishwasher tub, ensuring thorough cleaning of dishes.

Causes of a bad wash arm bearing include wear and tear over time, exposure to debris or hard water buildup, or physical damage due to impact or mishandling. A faulty bearing can lead to issues with the wash arm's rotation and water distribution.

Symptoms of a bad wash arm bearing include:

• Excessive noise or grinding sounds during the wash cycle
• The wash arm not rotating or spinning properly
• Uneven or incomplete cleaning of dishes
• Water not being distributed evenly within the dishwasher tub

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore dishwasher models.

Color: White. 4oz bottle with brush used for touching up damage to your dishracks. For blue use W10840471. For grey use WP676455. For tips use 675679

Includes one sprayarm.

Seal included. This sump housing assembly includes a 32.17 millimeter hole for the thermistor. If the hole for the thermistor is 31-31.5 millimeters you will need to order WP8534882.

This wax motor is the actuator for the dishwasher's rinse aid dispenser, releasing rinse agent at the correct time in the cycle. Replacing a weak or failed unit restores consistent rinse aid dispensing and helps minimize spotting.

• Actuates the rinse aid dispenser by extending a plunger when energized
• Works with the control to meter rinse aid during the final rinse
• Failure symptoms can include rinse aid not dispensing, the level never dropping, and increased spotting/filming on dishes
• Dispenser may remain closed with no audible actuation during the cycle

• Disconnect power at the breaker and shut off water before servicing
• Remove the door panel to access the dispenser; label and disconnect wires
• Release the old motor and install the new one in the same orientation, ensuring it seats fully
• Run a test cycle to ensure the dispenser releases rinse aid

This coupler and hose assembly connects your portable dishwasher to the sink faucet during operation. It supplies fresh water and returns drain water to the sink, helping stop leaks and restore reliable filling and draining.

• Provides a quick-connect link to a compatible faucet adapter for temporary hookup
• Carries incoming water to the dishwasher and routes drain water back to the sink
• Maintains a secure, leak-resistant seal during wash and drain cycles
• Replace if the coupler won't attach or stay on the faucet, hoses are cracked/kinked, or you see leaks and poor fill/drain performance

• Unplug the appliance and turn off water before service
• Verify the faucet adapter and O-rings are in good condition; hand-tighten only—do not overtighten with tools
• Route hoses to avoid kinks and sharp bends
• Open the faucet slowly and run a short test cycle; check all connections for leaks

This drain hose extension kit increases the reach of your appliance's drain line so it can connect to a farther standpipe or sink, supporting proper drainage and reducing stress on fittings that can lead to leaks. What it does:

• Extends the existing drain hose to accommodate installations where the drain connection is farther away
• Helps maintain a secure, leak-resistant connection when routed correctly
• Useful when relocating the appliance, changing cabinetry, or updating plumbing
• Common signs you may need it: hose won't reach, kinks when stretched, or occasional water near the drain line

• One drain hose extension kit

• Disconnect power and shut off the water supply; have a towel or pan ready for residual water
• Join the extension to the existing drain hose with the proper coupling/clamps; tighten securely and avoid kinks or sharp bends
• Route and support the drain line per your model's installation guide and observe any maximum total hose length
• Run a short test cycle and check all joints for leaks

Bushing, Door spring

This miniature door switch is the snap-action interlock that tells the appliance when the door is closed. Replacing a worn or sticking switch restores reliable start/stop and proper door-status sensing for safe, consistent operation. What it does:

• Acts as the latch/interlock sensor for door open/closed status
• Signals the control to allow or prevent operation based on door position
• Typical symptoms include: won't start or shows a door message, stops when the door is bumped, or light/fan behavior doesn't match door position

• 1 miniature door switch

• Disconnect power before servicing. If working on a microwave, high voltage may be present even when unplugged—properly discharge the capacitor.
• Access the latch/interlock area; note wire positions and transfer one lead at a time to the new switch.
• Use a multimeter to confirm the switch changes continuity when pressed before reassembly.

This replacement upper spray arm restores strong spray coverage to the upper wash level of your dishwasher. It channels water through its jets and spins under pressure to help deliver consistently clean dishes on the top rack.

• Directs pressurized wash water to the upper wash level for thorough cleaning
• Rotates under water pressure for even spray coverage
• Helps clear food soils and detergent residue from dishes and glasses
• Common symptoms: poor cleaning on the upper rack, spray arm not spinning, clogged or cracked arm

• Disconnect power and shut off the water supply before servicing
• Open the dishwasher; remove the upper rack if needed for access
• Release or unthread the retainer and pull the old arm straight off; clear debris from the hub/feed port
• Seat the new arm and secure the retainer hand-tight; ensure the arm spins freely and run a test cycle

Note: Check Serial Number for correct part

This replacement door handle restores a secure grip and normal door operation on compatible Whirlpool appliances. It provides a like-for-like fit and finish to replace a damaged, loose, or worn handle so doors open and close reliably. What it does:

• Replaces a broken, cracked, or missing door handle to restore normal use
• Provides a solid grip so the door opens and closes smoothly
• Matches the original mounting points for straightforward fit
• Helps eliminate rattling or loose-handle symptoms

• One replacement handle

• Intended to be installed with the original mounting screws and hardware; only included items ship
• Turn off and unplug the appliance or shut off power at the breaker before servicing electrical appliances
• Use moderate force when aligning the handle to avoid damaging trim or fasteners

This coupler gasket creates a tight, leak-resistant seal at a coupler connection point, helping maintain proper operation of the assembly. Replace when the original gasket is worn, cracked, or flattened to prevent drips and seepage.

• Forms the seal between a coupler and its mating component
• Helps prevent water seepage and air intrusion at the joint
• Supports correct flow/pressure through the connection
• Common symptoms: drips at the fitting, moisture around the coupler, or needing to over-tighten to stop leaks

• Disconnect power and shut off water supply before servicing
• Relieve line pressure and place a towel to catch residual water
• Clean mating surfaces; seat the gasket squarely in the coupler recess
• Tighten fittings evenly; restore service and check for leaks

This switch assembly is used in select dishwashers to provide a precise open/closed electrical signal to the control. Replacing a worn or sticking switch helps restore consistent cycle operation and reliable responses from the affected function. What it does:

• Sends an on/off (open/closed) signal to the control for the related mechanism in your model
• Helps ensure the connected function engages only at the correct time
• Common symptoms of a failed switch can include: cycle won't start, intermittent stopping, or improper filling/draining behavior
• A sticking or heat-damaged switch may cause erratic operation or error alerts

• One switch assembly

• Disconnect power (and water supply if required by access) before servicing
• Access location is model-specific; photograph wiring and note terminal positions before removal
• Transfer or reuse existing mounting hardware as applicable; ensure firm terminal connections
• After install, check switch actuation and run a test cycle to normal operation