Need Help?
Call
Front bulkhead for your dryer drum assembly. Replace this structural component if it's cracked, damaged, or worn to restore proper drum support.
Replaces the belt tension pulley that maintains proper belt alignment in your dryer. Needed when pulley is squealing, cracked, or worn out.
I replaced the belt, belt tension pulley, both dryer drum roller axles and both drum support rollers. Although I bought 2 tumbler bearing kits, because those still look good I am saving them for when they go bad. The videos were fantastic! I also took pictures as I went of wiring so there would be no question where things went when reassembling. It should be noted some models have extra terminals near the sensor terminals... just be aware and look closely/take pics as you are taking things... Read more
Usually ships within 4 - 14 days
Felt pad installs under the drum glide to prevent metal-on-metal contact and reduce friction. Replace if worn, causing grinding noise or squealing.
I went on line and purchased all of the possible parts that could be worn out. I spent less than the service guy wanted to show up...The online videos were spot on. Two hours and it works like new! One of the best values on the Internet! Read more
The Door Handle is an OEM component for Whirlpool dryers. It provides convenient access to load and unload clothes through the dryer door opening.
Causes of a bad door handle can include normal wear and tear over extended use. Repeated clutching and releasing of the handle leads to fatigue of rubberized grip areas and loosening of mechanical connections. Accidental falls or impacts when transporting dry loads of clothes could also damage the handle structure or mounting.
Symptoms of a bad dryer door handle include:
Compatible models also include Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore dryers.
Separated oven door by removing screws. Inserted handle and secured with clips, and reassembledo door with screws provided. In served broiler handle and snappedal into place. Read more
Converting dryer from propane to natural gas? This orifice regulates gas flow in the burner assembly. Easy DIY fix, typically done in under 1 hour.
Confirmed parts needed through online chat with tech and followed video instructions for dryer conversion. Found a video online for range conversion. Replaced orifices for stove top and adjusted oven burner orifices and air shutters and inverted pin in pressure regulator to natural gas position. All went well with no problems, about an hour and a half to gather tools and complete both jobs. Probably could be done faster but I was taking my time. Read more
Low-friction bearing ring for smooth drum rotation. Replace when you hear squealing or scraping during cycles. Confirm fit with your model number.
Looked up the part on AppliancesPartsPros.com. Ordered the part. Installed now it works like new. Read more
Supports the dryer drum and prevents friction. Replace when you hear scraping noises or clothes catch between the drum and door. Confirm fit with model.
The root cause was the front glides. They were virtually gone, and the drum was on metal to metal. So I replaced them with a front glide kit. I also replaced the belt, rear rollers, and lint screen. I am happy to say all the parts fit perfectly, and I couldn't find a better price anywhere else. I will definitely keep you on file for the next time I need appliance parts! Thank you! Sincerely, pw Read more
Dryer lint screen door provides access to the lint filter. Replace if cracked, broken, or won't close properly. Verify fit with your model number.
Changed the old parts with the new ones. Unscrewed one side. The other side was broken Put the new parts together and screwed back into place Done. Everything works Read more
Plastic door cover
Removed from dryer with screwdriver and opened door to access outer glass panel. Replaced with new one and reassambled. Read more
Replace a damaged collector duct to restore proper ventilation airflow. This kit channels air from the appliance's intake to the exhaust path, helping reduce leaks, noise, and recirculation for consistent capture performance.
Took a screw driver lifted the top, Unscrewed two screws holding the front on the inside of the dryer one to left and one to the right. Laid the front on the floor and removed to other screws holding the collector in place, popped out old one cleaned all the lint and dust and popped the new one in put the new seal in place and done ! Read more
Stationary rack installs inside dryer drum to hold shoes, sweaters, and delicates flat without tumbling. Replace if cracked, broken, or missing.
Ordered a replacement...actually ordered 4 replacements because they arrived broken since they had no bubble pack inside the shipping box to protect the rack from UPS "gorillas". Finally got one that arrived without being broken. Hooray! (But it still didn't have bubble pack protection.) Read more
Dryer won't heat or overheats? This high limit thermostat cuts power when temperatures get too high. Common fix for no-heat issues. Easy install.
When I pulled out the dryer from the wall, I could see dust/lint had accumulated everywhere and the vent system was compromised. I vacuumed up the dust/lint accumulation outside and then inside the vent system. I then opened the lower cabinet to clean and check its condition. I removed the water steamer bottle and its sub-assembly and then the drum. After cleaning and inspecting components — both visually and with a multi-meter I determined the problem was the appliance doing what it was... Read more
Supports the front of your dryer drum for smooth rotation. Replace when you hear scraping noises or the drum wobbles. Confirm fit with your model number.
First time DIY dryer repair. Videos very helpful! Remove front. Found glides worn thin, paint on drum removed where glides located. Drum, cage and motor turned easily - must be OK. Thirteen year old dryer. Order glides & felt, might as well replace belt and rollers while there. First time order - could not have been easier! Received 2nd day. Replaced parts, reassembled & connected power. Ran for 3 minutes with scraping noise then stopped with burning odor. Disassembled dryer, smelled odor from... Read more
This rear support assembly stabilizes the appliance's rear housing and helps keep internal components aligned for smooth operation and reduced vibration. It restores proper rear-end support to prevent rubbing, noise, and uneven motion. What it does:
Replaced the roller and shaft. The roller had worn 1/4 of the way through the support shaft. Read more
Stacking kit bracket module that secures your dryer on top of a washer. Replaces cracked, broken, or missing brackets to restore safe stacking.
Just installed the kit with clear instructions. Read more
This power cord supplies electrical power to the appliance and replaces a damaged or worn cord to restore safe, consistent power delivery. The "as wrapped" packaging means the cord ships neatly coiled for protection in transit. What it does:
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.