Dishrack

This adjuster is a replacement door/hinge adjustment component that restores proper door alignment and closing action for compatible appliances. It helps re-establish correct clearance and reduces rubbing, binding, or uneven gaps. What it does:

• Provides the adjustment point for proper door alignment and smooth operation
• Helps correct doors that sit unevenly, rub, or don't seal consistently
• Restores the ability to fine-tune door position after hinge or cabinet repairs
• Reduces noise and wear caused by misaligned doors or panels

• One adjuster as shown

• Turn power off and disconnect the appliance before starting any repair
• Some disassembly of the door, hinge, or trim may be required
• Keep fasteners and small parts organized; verify orientation before final tightening

This holder secures a small appliance component in place to prevent movement and reduce noise and wear. It restores proper fit and helps keep connected lines and parts aligned for reliable operation. What it does

• Secures a hose, wire, or small assembly to the appliance frame to prevent rubbing or sagging
• Keeps components aligned to reduce vibration and rattling noises
• Helps maintain proper routing to avoid strain on connections
• Commonly replaced when loose, broken, or missing and causing movement or noise

• One holder

• Turn off power and, if applicable, water supply before starting work
• Inspect surrounding clips and fasteners; replace if damaged
• Install in the same orientation as the original; use proper fasteners if required

Color: gray. Measures about 1 inch high by 4 inches deep.

This small retaining clip secures trim, panels, or components in place to prevent rattling or detachment during normal operation. It's a simple, low-profile fastener that restores fit and function where the original clip has broken or gone missing. What it does:

• Holds panels, bezels, or wiring harnesses in position to stop vibration and movement
• Replaces worn, broken or missing clips that cause loose trim or gaps
• Helps maintain proper alignment of adjacent parts for reliable operation
• Works as a direct-fit fastening solution where the original clip is used

• One retaining clip

• Disconnect power to the appliance before attempting any repair
• Access may require removing panels or trim; use appropriate screwdrivers or trim tools
• Install by aligning the clip with the mating slot or hole and pressing firmly until it snaps into place

This tiered upper rack kit replaces a damaged or missing upper rack to restore secure placement and organized spacing for cups, small plates and dishwasher-safe items. It helps improve loading capacity and prevents small items from tipping during cycles. What it does:

• Provides a tiered shelf for cups, mugs and small dishware to keep items secure
• Restores proper rack alignment and rolling action for smooth in-and-out movement
• Reduces shifting or tipping of small items that can block spray arms or cause poor cleaning
• Replaces worn or broken rack components so dishes load and drain correctly

• Disconnect power to the dishwasher and turn off water supply before starting
• Slide out the old upper rack and remove any retained clips or stops before installing the new rack
• Check rollers, rails and clips for wear and replace if needed to ensure proper operation
• Handle edges carefully and reassemble all stops and fasteners; test rack travel before running a cycle

The Lower Dishrack is an OEM part for GE dishwashers. It provides a sturdy shelf for placing pots, pans, plates, and other dishware on the bottom level of the dishwasher interior. The lower dishrack supports dish loads, holding them securely in place during the wash cycles. 

Causes of a failing lower dishrack include long-term wear and tear, corrosion from exposure to water and detergents, damage from improper loading, and loose or broken components.

Symptoms of a bad lower dishrack:

• Difficulty sliding the rack in and out
• The rack getting stuck mid-cycle
• Broken or missing wheels/rollers
• Rust formation
• Bent or misshapen wires

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This replacement lower dishrack restores smooth rolling and secure loading on the bottom level of your dishwasher, helping plates, bowls, and pots stay in place for consistent spray coverage and reliable cleaning results. What it does

• Organizes and supports dishes, cookware, and utensils on the lower level during wash and dry cycles
• Rolls in and out on the tub rails for easy loading and unloading
• Positions items for effective spray coverage and drainage
• Replace if tines are broken, coating is peeling/rusting, the rack derails or won't roll smoothly, or items tip over

• One lower dishrack

• Turn off power to the dishwasher before servicing
• Pull the old lower rack straight out; release/remove any rack stops if present
• Transfer any removable accessories from the old rack (such as utensil basket or clips), if needed
• Slide the new rack onto the rails and verify smooth operation

This durable silverware basket holds forks, knives and other utensils securely during dishwasher cycles so small items stay corralled and clean. Fits into the dishwasher rack to keep cutlery organized and prevent items from falling through. What it does:

• Holds and organizes silverware and small kitchen utensils during wash cycles
• Keeps utensils upright and separated for better cleaning and drying
• Prevents small items from slipping into the dishwasher spray area or drain
• Replaces cracked, broken or missing baskets that allow cutlery to scatter

• No tools required; remove the lower rack and set the basket into the designated rack slots
• Ensure basket snaps or rests securely and does not interfere with rack movement or spray arms
• Inspect basket for cracks or sharp edges before use; discontinue use if damaged
• Always follow the appliance manufacturer's safety and installation instructions

The Lower rack roller and stud assembly is an OEM part for GE dishwashers. It supports smooth movement of the lower dish rack in and out of the tub.

Causes of a bad roller and stud assembly can include wear from repeated extension/retraction of the rack. Mineral buildup may also impede smooth operation over time.

Symptoms of a bad roller and stud assembly include:

• Difficulty fully extending or retracting the lower dish rack  
• Noisy squeaking or grinding noises when moving the rack
• Rack that does not glide easily or gets stuck partially out

Replacing the roller and stud assembly with this genuine GE part restores convenient access to dishes on the lower rack. Its quality ball bearings and durable construction enhance usability cycle after cycle.

This GE OEM replacement part is also compatible with Hotpoint, RCA, and some Kenmore dishwasher models.
 

The Dishrack Stop Clip is an OEM component specifically designed for Whirlpool brand dishwashers. This clip functions to hold the upper dish rack in place during washing cycles.

Symptoms of a bad dishrack stop clip can include:

• Movement or vibration of the upper dish rack during washing
• Visible damage, bending or broken tabs on the mounting clip itself  
• Inability to smoothly slide or remove the upper dish rack

Causes of a bad dishrack stop clip usually stem from normal wear and tear over extended use. Overtight loading of dishes could also put excessive stress on the clip.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

This is a replacement dishwasher rack assembly with factory-installed wheels. It restores smooth sliding and safe loading when the original rack is bent, rusted, or missing rollers—helping the rack glide properly and keep items positioned during the wash.

• Holds and organizes dishes, glasses, and cookware during cycles
• Integrated wheels ride on the tracks for easy loading and unloading
• Replace if tines are rusted/broken, wheels are cracked or missing, or the rack derails
• Helps prevent items from tipping and maintains consistent spray coverage

• Disconnect power to the dishwasher before servicing
• Open the door, extend the rack, release any rail end-stops, and remove the old rack
• Transfer any removable accessories from the old rack to the new one, if needed
• Slide the new rack onto the rails and reinstall end-stops; verify smooth operation