Dryer Bracket & Flange

This bracket strike secures the door latch strike to the appliance frame, restoring reliable door closing and sealing. Replacing a damaged or bent bracket helps prevent doors from popping open or failing to latch properly. What it does:

• Secures the door strike so the latch can engage and hold the door closed.
• Restores correct door alignment when a worn or broken bracket causes improper latching.
• Addresses symptoms such as a door that won't latch, pops open, or sits unevenly.
• Provides a direct-fit structural replacement for the original mounting point.

• Disconnect power (and water, if applicable) before beginning any service.
• Access the bracket by removing the door trim or inner panel as required; keep original fasteners.
• Align the strike with the latch, secure with appropriate screws, and test door operation before reassembly.

This leg support secures the adjustable leveling foot to the appliance's base. Replacing a damaged or stripped support restores a solid mounting point so you can properly level the unit and reduce rocking and vibration. What it does

• Provides the mounting point for the leveling leg; anchors to the base/frame
• Helps keep the appliance level and stable during operation
• Replace if cracked, bent, or the threads are stripped
• Common symptoms: rocking or unstable unit, excessive vibration/rattling, doors out of alignment, leveling foot won't hold adjustment

• 1 leg support

• Disconnect power; shut off water or gas supply if applicable
• With a helper, carefully tip and support the unit to access the base safely
• Remove fasteners, transfer or thread the existing leveling leg into the new support, and reinstall
• Set the appliance down and level it on all corners; verify stability

This Heater Box Bracket secures the dryer's heater housing to the cabinet, keeping the heating assembly firmly mounted and aligned. Replace a bent, cracked, or missing bracket to restore stable support and reduce vibration around the heater area.

• Anchors the heater housing/box to the cabinet frame
• Maintains proper alignment and clearance for the heating element assembly
• Helps prevent rattling or rubbing noises from a loose heater housing
• A damaged bracket may leave the heater housing loose, cause vibration, or contribute to intermittent heating issues

• Disconnect power; if gas, shut off gas supply and allow the unit to cool completely
• Access the heater housing; note bracket orientation and reuse existing fasteners
• Support the heater housing and keep wiring clear while removing/installing the bracket
• After installation, verify the housing sits square and clear of the drum and wiring before restoring power

This stacking kit secures a dryer on top of a compatible washer to save floor space and stabilize the stacked units. It helps keep the dryer aligned and reduces shifting or rocking during use. What it does:

• Provides a secure connection between dryer and washer to create a stable stacked laundry configuration.
• Helps prevent the dryer from sliding, tilting, or shifting during spin cycles — common signs a stack kit is needed.
• Uses brackets and mounting hardware to fasten the dryer to the washer and maintain alignment.

• Disconnect power to both appliances and follow all safety precautions before starting installation.
• Have a second person assist when lifting or positioning the dryer to avoid injury or damage.
• Follow the OEM installation instructions and torque guidance for mounting hardware; ensure both appliances are level and stable after installation.

A replacement bracket glide that secures and guides an appliance drawer or shelf glide so drawers open and close smoothly. Installing a new bracket restores proper alignment and helps prevent sticking, sagging and noisy operation. What it does:

• Supports and guides the drawer/glide assembly for smooth, even movement.
• Keeps the drawer aligned so it does not bind, tip or come off the track.
• Reduces scraping, grinding or rattling noises caused by a damaged bracket.
• Common symptom: drawers that stick, sag, pull to one side, or feel loose.

• Disconnect power (or unplug) and empty the drawer before you start.
• Remove the drawer or access panel to reach the bracket; basic hand tools are usually required.
• Retain original fasteners unless the replacement explicitly includes new hardware.

This 38-inch stacking kit lets you securely mount a dryer on top of a matching washer to save floor space and stabilize the stacked units. It provides a tidy, secure connection for paired laundry appliances. What it does:

• Secures the dryer to the washer to reduce the risk of tipping or shifting during operation
• Keeps stacked appliances aligned for safer, more stable operation
• Helps minimize vibration transfer between machines for quieter performance
• Enables space-saving stacked installation in closets or compact laundry areas

• Follow the washer and dryer installation manuals and the kit instructions exactly for proper fit and safety
• Disconnect power and gas (if applicable) and empty both appliances before installing
• Installation may require two people and basic hand tools for safe handling of appliances

The Installation Kit is an OEM part for Frigidaire washing machines. It is a kit that provides all the necessary installation hardware to securely mount a washing machine on a pedestal. Having a properly installed and level pedestal is important to ensure stability during the wash cycle and reduce vibration and noise.

Causes may include missing hardware, damaged or worn parts in the existing pedestal, or inadequate installation. This replacement kit from Frigidaire includes mounts, brackets, screws, and leveling components to facilitate a straightforward and proper installation.

Symptoms of a bad or improperly installed pedestal can include:

• Excessive shaking and movement of the washer during operation
• Drain leakage or hose connections coming loose over time
• The washer developing alignment or leveling issues
• Noise and sounds that worsen over repeated use

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This dryer bearing bracket secures the drum's rear bearing to keep the drum aligned and rotating smoothly. Replacing a worn bracket can help reduce drum wobble, scraping noises, and uneven drum rotation. What it does:

• Supports and locates the rear drum bearing to maintain proper drum alignment.
• Helps prevent the drum from wobbling, rubbing, or scraping against the cabinet.
• Can reduce or eliminate grinding, squealing, or thumping noises caused by a loose or damaged rear support.
• Works with the dryer's rear bearing assembly to enable consistent drum rotation.

• Disconnect electrical power (and gas, if applicable) before beginning any repair.
• Access typically requires removing the dryer drum and rear bulkhead.
• Inspect the bearing, shaft, and surrounding glides; replace any worn components to prevent repeat failure.

This dryer stacking kit lets you securely mount a dryer on top of a compatible front-load washer to save floor space and create a stable stacked laundry pair. Designed to match factory mounting points for reliable fit and function. What it does:

• Provides a rigid bracket system that positions and secures the dryer on top of the washer
• Helps prevent shifting, tipping, and excessive vibration when properly installed
• Enables safe stacked installation where the washer and dryer are compatible
• Useful when replacing a lost or damaged factory stacking bracket or mounting hardware

• Follow the OEM installation instructions exactly and confirm compatibility before installing
• Install with two people to safely lift and align the dryer onto the washer
• Disconnect electrical power (and gas, if applicable) to appliances before starting work
• Use only the provided hardware and mounting locations; improper installation can cause instability

This stacking kit secures a compatible dryer to a matching washer to create a safe, space-saving stacked laundry configuration. It helps stabilize the dryer and reduces movement during use for a more reliable setup. What it does:

• Provides brackets and mounting hardware to fasten the dryer to the washer
• Helps prevent the dryer from shifting or tipping when the washer is running
• Improves overall stability of stacked laundry appliances during normal operation
• Reduces vibration-related movement that can cause noise or misalignment

• Disconnect power to both appliances before installing and follow all manufacturer instructions
• Use only on compatible washer/dryer pairs
• Tighten hardware securely but avoid overtightening; follow torque guidance in OEM instructions

This rear level leg bracket replaces the rear mounting bracket that secures a leveling leg to the appliance frame, restoring proper support and helping keep the appliance stable and level for safe, quiet operation. What it does:

• Secures the rear leveling leg to the appliance frame so the cabinet sits evenly
• Restores proper height and prevents the appliance from tilting backward
• Reduces rocking, wobbling, and vibration caused by a damaged or loose bracket
• Helps maintain safe, stable operation under normal load conditions

• Disconnect power (and gas supply if applicable) and move the appliance to a safe, accessible area before starting.
• Support the appliance cabinet so it cannot tip when the rear leg or bracket is removed.
• Use basic hand tools to remove and install the bracket; follow the appliance manufacturer's instructions.
• Inspect the leveling leg and front mounts while servicing; replace any worn or damaged hardware.

This is a mounting bracket that secures and supports appliance components, helping keep panels and assemblies aligned for stable operation. It's a simple replacement part that restores proper fit and reduces movement or rattling. What it does:

• Secures and supports a panel or internal assembly to the appliance frame
• Keeps components aligned to prevent binding or misalignment
• Reduces vibration and rattling caused by loose fittings
• Restores proper mechanical support after breakage or wear

• Disconnect power and/or water to the appliance before beginning any repair
• Use appropriate hand tools; keep track of fasteners and any shims or clips
• Beware of sharp sheet-metal edges; wear gloves and eye protection

This hinge bracket secures the refrigerator door hinge assembly so the door opens and closes smoothly and stays aligned. Replaces a worn or damaged bracket to restore proper door fit and reduce binding or sagging. What it does:

• Provides a stable mounting point for the door hinge shaft to keep the door aligned
• Restores correct door swing and sealing when original bracket is cracked or bent
• Helps stop door sag, rubbing, or uneven gaps that can cause cooling issues
• Durable molded metal/plastic construction resists wear from normal use

• One hinge bracket

• Recommended for technicians or experienced DIYers; disconnect power and empty door before starting
• Use correct screws and torque; reuse existing fasteners only if undamaged
• Inspect adjacent hinge parts and seals; replace any damaged components to ensure proper alignment
• Handle carefully to avoid damaging door finish and to maintain proper hinge geometry

This bracket belt switch assembly secures the dryer belt switch and helps stop the motor if the belt slips or breaks, protecting the dryer from damage and preventing unsafe operation. It's a direct-fit replacement for the original mounting assembly. What it does

• Holds the belt switch in the correct position so it can sense belt tension.
• Opens the circuit when the belt is loose or broken to stop motor operation.
• Can resolve symptoms like a dryer that stops mid-cycle, fails to start, or runs but won't tumble.
• Restores the original mounting and switch alignment for reliable belt sensing.

• One bracket belt switch assembly

• Disconnect power before beginning—this part is used on electric and gas dryers.
• Basic hand tools (screwdriver/socket) are typically required; keep track of mounting hardware.
• Inspect the belt and pulleys while replacing the bracket; replace any worn parts.

This support bracket secures and stabilizes internal components to keep your appliance operating reliably. It provides a simple, durable mounting point to restore proper alignment and reduce movement or rattling. What it does:

• Provides a secure mounting point for internal panels or assemblies
• Helps prevent component shift that can cause noise or misalignment
• Restores part-to-part spacing for proper operation
• Replaces damaged, bent, or broken brackets that no longer hold components

• Disconnect power before accessing internal panels or mounting points
• Installation may require removal of the appliance access panel and basic hand tools
• Retain and reuse original fasteners if undamaged; use OEM-specified hardware when required