Dryer Knob, Dial & Button

This timer knob mounts on the appliance's mechanical timer shaft and lets you select cycles and settings. Replace a cracked or stripped knob to restore smooth, positive control of the timer and accurate cycle selection.

• Attaches to the timer shaft so you can set cycle and time
• Provides a secure grip for selecting and adjusting settings
• Common symptoms: knob spins without moving the timer, feels loose, cracked, or missing
• Helps restore proper engagement when the hub is worn or stripped

• Disconnect power before servicing
• Pull the old knob straight off the timer shaft
• Align the flat/splines of the new knob with the shaft and press on firmly
• Rotate through a full turn to confirm proper engagement

This control knob replaces a worn or broken knob so you can reliably set and adjust your appliance's settings again. It restores a smooth, positive feel and clear pointer alignment for everyday use.

• Selects and adjusts the matching control (such as burner, temperature, or function) on the appliance
• Worn, cracked, or missing knob can make settings hard to change or read
• Loose or slipping knob may prevent the control shaft from turning properly
• Cosmetic damage can detract from the appliance's appearance

• Disconnect power and allow hot surfaces to cool before servicing
• Pull the old knob straight off the control shaft; do not twist against stops
• Align the flat or D-shaped opening with the shaft and press firmly until seated
• If the knob won't seat, inspect the shaft for damage or debris before reinstalling

Replace a worn or missing control button with this push button cap. It fits over the control panel's switch actuator to restore a clean look and reliable button feel when selecting settings.

• Provides the surface you press to actuate the underlying control switch
• Helps align and protect the switch from dust and everyday wear
• Restores proper button travel and tactile feedback
• Common symptoms: missing or cracked cap, button feels loose or wobbly, sticks or doesn't respond consistently

• Disconnect power to the appliance before servicing
• Gently pry off the old cap from the front without marring the panel
• Align the new cap with the switch stem/actuator and press until fully seated
• Test button movement and operation before completing reassembly

Color: White. Measures about 3 inches in diameter.

Restore smooth, accurate control with this replacement control knob. It fits onto the selector or timer shaft so you can choose cycles, temperatures, or time and replace a cracked, stripped, loose, or missing knob.

• Attaches to the control shaft to operate a switch, timer, or thermostat
• Provides a secure grip for selecting cycle, temperature, speed, or time
• Resolves issues like free-spinning, slipping, or knobs that won't stay on
• Helps when settings can't be adjusted due to a damaged or missing knob

• Disconnect power before servicing to prevent accidental start
• Pull the old knob straight off; avoid twisting the control shaft
• Align the new knob with the shaft and press firmly until fully seated
• If your original knob had a removable insert/retainer, transfer it to the new knob

The Dryer Timer Dial Skirt is an OEM part designed specifically for Whirlpool dryers. It acts as a protective and decorative cover around the timer dial, providing clear labeling for various dryer settings. 

Color: Bisque

Over time, the dial skirt may degrade due to frequent use, exposure to heat, and potential impact, leading to cracks, discoloration, or broken markings. These issues can make selecting the appropriate cycle difficult or confusing.

Signs that the Dryer Timer Dial Skirt may need replacing include:

• Faded or illegible cycle markings
• Cracks or broken sections on the skirt
• The dial skirt no longer fitting snugly

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Replacement control knob (dial) for appliance control panels. Restores a secure grip for selecting settings when the original knob is cracked, worn, loose, or missing. What it does:

• Replaces a damaged or worn control knob to restore tactile feedback and accurate selection.
• Makes it easy to turn and set controls that were slipping or stripped.
• Helps prevent accidental changes by providing a firm, centered grip.
• Works with compatible push-on control shafts to align selection markings.

• Disconnect power to the appliance before removing or installing parts.
• Pull the old knob straight off the control shaft; align the new knob to the shaft and push on until it seats.
• Do not force if the knob does not fit—verify shaft style and orientation first.

This cycle selector knob is used on some Maytag washers and dryers. This is not the timer knob. Color: stainless steel. Measures about 2 inches in diameter where the handle extends.

This plated control knob replaces a worn or missing knob on your range or cooktop, restoring smooth burner adjustment and a matching look. It pushes onto the existing control stem and operates like the original. What it does:

• Mounts on the burner control stem to set and adjust heat levels
• Replaces cracked, stripped, loose, or missing knobs to restore proper control
• Provides clear pointer orientation for consistent settings
• Symptoms it can help with: knob falls off, wobbly/loose feel, hard to turn, won't engage

• One plated control knob assembly

• Disconnect power and let the cooking surface cool; if applicable, turn off gas supply.
• Pull the old knob straight off the stem—avoid prying or side pressure that can damage the shaft.
• Align the new knob with the stem and press straight on until fully seated.
• Test the control for smooth operation before regular use.

This parts assembly is a model-specific collection of small components used to complete or restore proper installation and fit. It replaces missing or worn pieces so affected areas mount securely and operate as designed. What it does:

• Provides the factory-specified hardware/trim for your model
• Restores secure mounting and proper alignment of affected components
• Helps eliminate rattles, gaps, or looseness caused by missing hardware
• Useful after service or moves when original pieces are lost

• One parts assembly

• Disconnect power; shut off water or gas before service
• Wear gloves; watch for sharp edges and small parts
• Reference your model's service/installation manual to match and place each piece
• Install hardware snugly; avoid overtightening plastic components

The Knob is an OEM component for Whirlpool dryers. As the user interface, it allows selections of temperature, settings, and time options with the twist of a finger.

Designed for comfort during extended cycles, the durable knob utilizes non-slip textured surfaces around robust internal gears. Integrated fasteners mount securely to shafts coupling knobs to their respective switches. 

Causes of faulty knobs can include stripped internal teeth from mineral deposits binding moving parts or broken mounting tabs weakened through normal wear over many years.

Symptoms of a damaged knob include:

• Failure to engage settings or spin freely  
• Dials loose on shaft allowing accidental shifts   
• Missing labels from normal cleaning/wear reducing visibility
• Cracks or breaks compromising seal against moisture

Replace yours today with this genuine Whirlpool knob to restore easy navigation of cycles. Compatible with Kenmore and some Maytag dryers.

White

This replacement control knob restores reliable, easy adjustment of your appliance's settings. Use it when the original knob is cracked, stripped, loose, or missing to regain precise control and a secure grip. What it does:

• Re-establishes firm manual control for setting temperatures, cycles, or power levels.
• Replaces cracked, worn, or stripped knobs that slip or won't turn properly.
• Restores alignment of the selection indicator for accurate setting reference.
• Provides a direct fit onto the appliance's control shaft splines for secure operation.

• Always disconnect power to the appliance (and shut off gas for ranges) before servicing.
• Remove the old knob by pulling it straight off the control shaft; align splines and push the new knob on until fully seated.
• If the knob won't seat easily or slips after installation, do not force it — inspect the control shaft splines for damage.

Color: chrome. The main part of the knob is about 1 inch in diameter. The handle is about 2 inches.

This replacement timer knob lets you set and turn the dryer's cycle timer smoothly and reliably, restoring easy selection of drying times and cycle settings. Designed as the correct white knob assembly for compatible Whirlpool dryers. What it does:

• Fits onto the dryer timer shaft so you can rotate and select drying cycles and times.
• Replaces a cracked, stripped, loose or missing timer knob that prevents proper control.
• Provides a secure, tactile grip for accurate setting changes.
• Matches the original White finish for a clean, factory look.

• Disconnect the dryer from power before servicing.
• Most knobs pull straight off the timer shaft; align splines and press the replacement fully into place.
• Inspect the shaft and any retained plastic insert; transfer insert if the replacement does not include it.
• If knob is difficult to remove, use steady, even force or a soft-padded puller to avoid damaging the control panel.

This selector knob attaches to the control shaft so you can choose cycles and options on your appliance. Replace a cracked or stripped knob to restore smooth, accurate settings without forcing or damaging the control stem.

• Attaches to the control shaft to operate the cycle/timer or option switch
• Common symptoms: knob is cracked, stripped, loose, spins freely, falls off, or is missing
• Restores positive, accurate control feel when selecting settings

• Disconnect power before servicing
• Pull the old knob straight off the shaft; avoid prying against the control panel
• Align the keyed/flat side and press the new knob on until fully seated
• If your original knob used a spring clip or insert, transfer it to the new knob before installation