Dryer Leg Or Foot

Adjustable leveling leg with foot pad for dryers, washers, and pedestals. Replace cracked, broken, or missing legs to stabilize your appliance.

Adjustable leveling leg threads into the dryer base for stable footing. Replace missing, worn, or broken legs to level your unit on uneven floors.

Adjustable leveling leg stabilizes your dryer on uneven floors. Replace if cracked, broken, or worn from vibration and repeated adjustments.

This leveling leg assembly supports and stabilizes your washer by allowing you to adjust its height for a level installation. Keeping the appliance level helps reduce vibration, noise, and movement during operation.

• Adjusts the washer's stance to ensure it sits level on the floor
• Helps prevent excessive vibration, walking, and rattling noises
• Supports proper spin performance by improving machine stability
• Common fix when a foot is worn, damaged, or will not hold adjustment

• Unplug the washer and turn off water supply before servicing
• Tip the appliance carefully to access the leveling point
• Thread the new leg into the base and adjust until level; lock if applicable
• Verify all legs contact the floor firmly and recheck level after test run

Adjustable leveling feet that restore stability and balance to your appliance by letting you fine-tune height at each corner for a flat, wobble-free install—helps reduce vibration and improve door fit and operation. What it does:

• Provides adjustable height to level an appliance on uneven floors.
• Eliminates rocking or wobbling that can cause vibration, noise or movement during operation.
• Helps ensure doors and panels sit flush and seal properly.
• Durable replacement designed for direct fit where the OEM leveling foot is specified.

• Disconnect power and water before performing any work.
• Support the appliance so it cannot tip—use a jack or have a helper hold it while you adjust feet.
• Turn the foot to raise or lower the corner; use hand tools as needed and avoid excessive force.
• After adjusting, check stability and run a short cycle to ensure vibration and alignment are resolved.

This leveling foot assembly restores a stable, level base so your machine runs smoothly and stays in place. It replaces a worn or stripped foot with a new bolt, pad, and nut to secure the adjustment.

• Levels and supports the appliance by adjusting the foot height
• Helps reduce vibration, rocking, and walking during operation
• Replaces stripped, bent, or rusted foot bolts and worn or missing pads
• Holds the set height with the included nut to maintain alignment

• Disconnect power; for washers, turn off water supply before servicing
• Carefully tip and support the appliance to access the feet
• Thread the new foot into the base, seat the pad, and tighten the nut
• Level front-to-back and side-to-side; ensure all feet are firmly on the floor

I want to write the highest-accuracy, conversion-ready title and description, but I need to verify the OEM part's official name and function first to prevent incorrect guidance and returns. Please share either:

• An image of the part on the APP PDP, or
• The OEM/Alliance description for part 40016001 (replacement for 34318), or
• The appliance area/function this part serves (for example: hinge bushing, valve, knob, clip, seal, etc.)

Adjustable leveling foot for dryers. Replaces worn, broken, or missing legs to stabilize your dryer and stop rocking on uneven floors.

This replacement rubber foot cushions the machine's contact point with the floor to improve stability, reduce vibration, and protect surfaces. Replace a worn or missing foot to restore steadier, quieter operation and easier leveling.

• Provides a cushioned, non-slip contact point between the appliance and floor
• Helps absorb vibration and reduce rattling or movement during cycles
• Aids in proper leveling and overall stability
• Replace when cracked, flattened, or missing, or if the unit rocks or "walks"

• Disconnect power; for washers, also turn off water. If applicable, shut off gas supply
• Carefully tilt or raise the appliance with assistance and proper lifting support
• Remove the worn foot and install the new foot on the leveling leg or base as designed, ensuring it seats fully
• Re-level the appliance and tighten any locknuts; verify stable operation

Adjustable leveling leg for dryers. Installs at the base to stabilize and level your appliance. Replace if broken, cracked, or missing threads.

Replace a broken or worn caster wheel on your dryer. This kit includes one rolling caster and washers for stable support and easy movement across floors.

Leveling leg for dryers and laundry centers. Installs at the base to stabilize and level your appliance. Replace if broken, worn, or missing.

Adjustable leveling leg and bracket assembly for dryers. Installs at the base to stabilize and level your unit. Replace missing, broken, or worn feet.

This Leveling Leg is an OEM replacement part for GE washing machines and dryers. It plays an essential role in maintaining the stability and balance of the appliance. This leveling leg is designed to withstand the weight and vibrations of the machine, ensuring it remains level and operates smoothly.

Over time, leveling legs can wear down, become damaged, or lose their ability to adjust properly due to constant vibrations, uneven flooring, or shifting of the appliance. An unbalanced appliance can lead to inefficient operation, increased wear and tear, and potential safety hazards.

Symptoms of a bad Leveling Leg include:

• The appliance is unstable or wobbles during operation.
• Excessive noise or vibration more than usual.
• Difficulty in aligning the appliance level on the floor.
• Visible wear or damage to the leveling leg.
• The appliance tilts or leans to one side.

This GE OEM replacement part is compatible with Hotpoint, RCA, and Kenmore models.

Adjustable leveling leg installs at the rear of your dryer to lift and balance the unit. Replace if broken, cracked, or missing for proper stability.